Easy-JTAG HOT Update. v1.9.1.0. Repair dead EMMC KMVYL000LM-B503!! First in World - Page 4 - GSM-Forum

joel_3mo · 04-28-2015, 06:35

I know it is not the place to post/ask this, but i would to know what is "Easy-JTAG NOKIA Update 2.0.0.0" shown in easy-jtag page of updates.
Is it an error or what?
Please check this.

**blang** · 04-28-2015, 08:16

Quote:

Originally Posted by joel_3mo

I know it is not the place to post/ask this, but i would to know what is "Easy-JTAG NOKIA Update 2.0.0.0" shown in easy-jtag page of updates.
Is it an error or what?
Please check this.

this is ADVANCED NOKIA FLASHER (ANF)

joel_3mo · 04-30-2015, 16:59

Quote:

Originally Posted by blang

this is ADVANCED NOKIA FLASHER (ANF)

Thanks for reply, but is this a function we can use with our jtag box? How?

mojahed.br · 05-04-2015, 12:04

need emmc update framware for MAG2GA

ganjbek · 08-06-2015, 11:59

sm-t211 emmc dead repair done

Z3X EasyJtag Box JTAG Софт версия. 2.0.3.0
Loading eMMC Addon Firmware... IO: 3300 mV
Box С/Н: 0D0110----------, ,Микропрограмма Вер.: 01.52
Напряжение подтяжки линии CMD :2114 mV
Напряжение активной линии CMD :3093 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
Изготовитель eMMC: ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 197379 MB
EMMC ROM2 (Boot Раздел 1) Емкость: 3072 kB
EMMC ROM2 (Boot Раздел 2) Емкость: 3072 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 3072 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.24 (MMC Unknown)
Boot bus config [177]: 0x18 , width 1bit , Partition config [179]: 0x18.
Backup saved: 000000_ 537986854_20150704_1553.extcsd
Сделано.

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KLM8G1WE4A-A001
Z3X EasyJtag Box JTAG Софт версия. 2.0.3.0
Loading eMMC Addon Firmware... IO: 3300 mV
Box С/Н: 0D0110----------- ,Микропрограмма Вер.: 01.52
Напряжение подтяжки линии CMD :2114 mV
Напряжение активной линии CMD :3093 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Сделано.

Z3X EasyJtag Box JTAG Софт версия. 2.0.3.0
Loading eMMC Addon Firmware... IO: 3300 mV
Box С/Н: 0D01101---------- ,Микропрограмма Вер.: 01.52
Напряжение подтяжки линии CMD :2103 mV
Напряжение активной линии CMD :2670 mV
eMMC Device Information
EMMC CID : 1501004D38473157300020127A4E31F0
EMMC CSD : D02701320F5903FFF6DBFFE18E404028
Изготовитель eMMC: ID: 0015 , OEM ID: 0100
EMMC Date: 03/2014 Rev.0x0
EMMC NAME: M8G1W0 , S/N: 538081870
EMMC NAME (HEX): 4D384731573000
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Раздел 1) Емкость: 2048 kB
EMMC ROM2 (Boot Раздел 2) Емкость: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: M8G1W0_ 538081870_20150704_1554.extcsd
Сделано.

ganjbek · 08-06-2015, 13:44

pls add new update image tp emmc KLM8G1WE4A-A001 'M8G1WA " link

anombase · 09-16-2015, 18:06

Quote:

Originally Posted by BABAK NURI

if you have this error in last step and not detect anymore,,You must use TP and Repair again

is it possible to connect TP on board?

elbasri73 · 01-25-2016, 16:55

Z3X EasyJtag Software ver. 1.0.109.0
Loading eMMC Addon Firmware...
CMD Pullup Level:1742 mV
CMD Active Level:20299 mV
eMMC ACK Error ( Check Connection )
eMMC Card initialisation error!

mifluvcute · 01-25-2016, 17:29

Quote:

Originally Posted by elbasri73

Z3X EasyJtag Software ver. 1.0.109.0
Loading eMMC Addon Firmware...
CMD Pullup Level:1742 mV
CMD Active Level:20299 mV
eMMC ACK Error ( Check Connection )
eMMC Card initialisation error!

check your soldering brother, make sure the connection is good, and try to set the voltage from 1.8v-3.3v

topline · 03-08-2016, 22:18

because you have to do and where test point to ground?
vorri understand if it is possible to test point without removing the EEMC ...
thank you

Reliable Shop · 12-04-2016, 09:50

Quote:

Originally Posted by BABAK NURI

if you have this error in last step and not detect anymore,,You must use TP and again

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0200501655800F2C, ,FW Ver.: 01.55
CMD Pullup Level:1350 mV
CMD Active Level:2423 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower mode is ON!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

how to solve this problem.....

Munir · 12-05-2016, 13:58

Quote:

Originally Posted by Reliable Shop

Z3X EasyJtag Software ver. 2.4.1.1

Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0200501655800F2C, ,FW Ver.: 01.55
CMD Pullup Level:1350 mV
CMD Active Level:2423 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower mode is ON!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

how to solve this problem.....

your emmc is dead. its need emmc reset on tp of emmc after removing.
And you had not indicate emmc full name (VTU00M ...etc) your model

chmsc_ELX · 09-05-2018, 12:28

N7105 dead boot...

z3x easy Jtag read this on detect emmc.... tried repeating removing all the lines and detect the esult is the same.

Quote:

Compression is ON
Z3X EasyJtag Software ver. 3.1.0.0
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0EXXXXXXXX, ,FW Ver.: 01.63
CMD Pullup Level:1320 mV
CMD Active Level:2310 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

layder · 09-06-2018, 16:00

Quote:

Originally Posted by chmsc_ELX

N7105 dead boot...

z3x easy Jtag read this on detect emmc.... tried repeating removing all the lines and detect the esult is the same.

Try to repair eMMC firmware via use Test Point, and post log of operation

**chand_gee** · 09-06-2018, 19:46

Quote:

Originally Posted by chmsc_ELX

N7105 dead boot...

z3x easy Jtag read this on detect emmc.... tried repeating removing all the lines and detect the esult is the same.

i m facing same error with many emmc theise days can you post emmc number
http://forum.gsmhosting.com/vbb/f672...orted-2465981/

04-28-2015, 06:35	#46 (permalink)
joel_3mo No Life Poster Join Date: Nov 2013 Location: Third World ;) Posts: 498 Member: 2061381 Status: Offline Sonork: 100.1673769 Thanks Meter: 129	I know it is not the place to post/ask this, but i would to know what is "Easy-JTAG NOKIA Update 2.0.0.0" shown in easy-jtag page of updates. Is it an error or what? Please check this.

05-04-2015, 12:04	#49 (permalink)
mojahed.br No Life Poster Join Date: Dec 2014 Location: u.a.e Posts: 509 Member: 2320256 Status: Offline Sonork: 100.1661545 Thanks Meter: 50	need emmc update framware for MAG2GA

08-06-2015, 11:59	#50 (permalink)
ganjbek No Life Poster Join Date: Feb 2010 Location: 90-region Age: 39 Posts: 938 Member: 1246378 Status: Offline Thanks Meter: 123	sm-t211 emmc dead repair done Z3X EasyJtag Box JTAG Софт версия. 2.0.3.0 Loading eMMC Addon Firmware... IO: 3300 mV Box С/Н: 0D0110----------, ,Микропрограмма Вер.: 01.52 Напряжение подтяжки линии CMD :2114 mV Напряжение активной линии CMD :3093 mV eMMC Device Information EMMC CID : 1501003030303030305620110726589C EMMC CSD : 902701320F5903FFF6DBFFEF8A404022 Изготовитель eMMC: ID: 0015 , OEM ID: 0100 EMMC Date: 05/2005 Rev.0x56 EMMC NAME: 000000 , S/N: 537986854 EMMC NAME (HEX): 30303030303000 EMMC ROM1 (Main User Data) Capacity: 197379 MB EMMC ROM2 (Boot Раздел 1) Емкость: 3072 kB EMMC ROM2 (Boot Раздел 2) Емкость: 3072 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 3072 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.24 (MMC Unknown) Boot bus config [177]: 0x18 , width 1bit , Partition config [179]: 0x18. Backup saved: 000000_ 537986854_20150704_1553.extcsd Сделано. Running:SAMSUNG: eMMC firmware update... Confirmed eMMC Part Number: KLM8G1WE4A-A001 Z3X EasyJtag Box JTAG Софт версия. 2.0.3.0 Loading eMMC Addon Firmware... IO: 3300 mV Box С/Н: 0D0110----------- ,Микропрограмма Вер.: 01.52 Напряжение подтяжки линии CMD :2114 mV Напряжение активной линии CMD :3093 mV Setup firmware update mode, wait 2..30 sec... Success! Sending eMMC firmware... Success! Verifying eMMC firmware... Success! Flashing eMMC firmware... Success! Repairing eMMC CID... Success! eMMC firmware is updated now! Please reconnect all eMMC lines before next operation! Please don't forget to repair extCSD from backup! Please don't forget to configure BOOT sizes! Сделано. Z3X EasyJtag Box JTAG Софт версия. 2.0.3.0 Loading eMMC Addon Firmware... IO: 3300 mV Box С/Н: 0D01101---------- ,Микропрограмма Вер.: 01.52 Напряжение подтяжки линии CMD :2103 mV Напряжение активной линии CMD :2670 mV eMMC Device Information EMMC CID : 1501004D38473157300020127A4E31F0 EMMC CSD : D02701320F5903FFF6DBFFE18E404028 Изготовитель eMMC: ID: 0015 , OEM ID: 0100 EMMC Date: 03/2014 Rev.0x0 EMMC NAME: M8G1W0 , S/N: 538081870 EMMC NAME (HEX): 4D384731573000 EMMC ROM1 (Main User Data) Capacity: 7456 MB EMMC ROM2 (Boot Раздел 1) Емкость: 2048 kB EMMC ROM2 (Boot Раздел 2) Емкость: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: M8G1W0_ 538081870_20150704_1554.extcsd Сделано.

08-06-2015, 13:44	#51 (permalink)
ganjbek No Life Poster Join Date: Feb 2010 Location: 90-region Age: 39 Posts: 938 Member: 1246378 Status: Offline Thanks Meter: 123	pls add new update image tp emmc KLM8G1WE4A-A001 'M8G1WA " link

01-25-2016, 16:55	#53 (permalink)
elbasri73 Freak Poster Join Date: Sep 2006 Location: morrocco Posts: 149 Member: 345974 Status: Offline Thanks Meter: 23	Z3X EasyJtag Software ver. 1.0.109.0 Loading eMMC Addon Firmware... CMD Pullup Level:1742 mV CMD Active Level:20299 mV eMMC ACK Error ( Check Connection ) eMMC Card initialisation error!

03-08-2016, 22:18	#55 (permalink)
topline No Life Poster Join Date: Oct 2004 Location: italy Posts: 501 Member: 85139 Status: Offline Thanks Meter: 68	because you have to do and where test point to ground? vorri understand if it is possible to test point without removing the EEMC ... thank you