emmc n7100 i9300

[johntba]

hi everybody
my gueastion is for emmc n7100 or i9300 partitioning with z3x.

I have connected with pinouts the phone and with detect emmc everything is fine.This means that my connections and voltage is good.The problem is that i format button return unsupported nand emmc and also i can not find any partition button.Somewhere i saw about emmc tool pro version with more options for october of 2013 users and before.
Any help is welcome
Thank you in advance

[blang]

Originally Posted by johntba

hi everybody
my gueastion is for emmc n7100 or i9300 partitioning with z3x.

I have connected with pinouts the phone and with detect emmc everything is fine.This means that my connections and voltage is good.The problem is that i format button return unsupported nand emmc and also i can not find any partition button.Somewhere i saw about emmc tool pro version with more options for october of 2013 users and before.
Any help is welcome
Thank you in advance

Try read/write. Only then you will sure voltage is ok.
About formatting and partition - under beta at this moment.Wait for public release.

[mobilegsm30]

Hello blang
N7100 Emmc Read ok but write not possible its Emmc damage or other? phone is dead, see log

file...E:\EasyJtag\N7100\N7100_Rom2_Alive_Boot_BN\ N7100_Rom2_Alive_Boot_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9XXXX, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2361 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 00100000 bytes to 00000000 ...ROM1
eMMC ACK Error at addr:0x0
Reading dump to file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ EMMC_00000000_00100000.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9XXXX, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1608 mV
CMD Active Level:2361 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Switching EMMC partition...
Reading 00100000 bytes from 00000000 ...ROM2
Read Speed: 208 kB/s
Done !!!

[mobilegsm30]

Hello Blang

After lots of try now write both files in n7100 but still not power on. only red light blink on top.


Resources ver. : MainRC ver.OCD040Z001 (C)2012 z3x-team.com
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2340 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
=============================================
Extended CSD rev 1.6 (MMC 4.5)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x01]:
implementation based on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Max Packet Read Cmd [MAX_PACKED_READS: 0x3f]
Max Packet Write Cmd [MAX_PACKED_WRITES: 0x3f]
Data TAG support [DATA_TAG_SUPPORT: 0x01]
Data TAG Unit Size [TAG_UNIT_SIZE: 0x04]
Tag Resources Size [TAG_RES_SIZE: 0x00]
Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]
Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]
Extended partition attribute support [EXT_SUPPORT: 0x03]
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x02]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x10]
Access size [ACC_SIZE: 0x07]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x50]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x01d5a000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x02]
I/O Driver Strength [DRIVER_STRENGTH: 0x00]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x48]
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x01]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0000bb
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Periodic Wake-up [PERIODIC_WAKEUP]: 0x00
Program CID/CSD in DDR mode support [PROGRAM_CID_CSD_DDR_SUPPORT]: 0x01
Native sector size [NATIVE_SECTOR_SIZE]: 0x00
Sector size emulation [USE_NATIVE_SECTOR]: 0x00
Sector size [DATA_SECTOR_SIZE]: 0x00
1st initialization after disabling sector size emulation [INI_TIMEOUT_EMU]: 0x00
Class 6 commands control [CLASS_6_CTRL]: 0x00
Number of addressed group to be Released[DYNCAP_NEEDED]: 0x00
Exception events control [EXCEPTION_EVENTS_CTRL]: 0x0000
Exception events status[EXCEPTION_EVENTS_STATUS]: 0x0000
Extended Partitions Attribute [EXT_PARTITIONS_ATTRIBUTE]: 0x0000
Packed command status [PACKED_COMMAND_STATUS]: 0x00
Packed command failure index [PACKED_FAILURE_INDEX]: 0x00
Power Off Notification [POWER_OFF_NOTIFICATION]: 0x00
Control to turn the Cache ON/OFF [CACHE_CTRL]: 0x00
Writing file...E:\EasyJtag\N7100\N7100_Rom2_Alive_Boot_BN\ N7100_Rom2_Alive_Boot_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2320 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 00100000 bytes to 00000000 ...ROM1
Write Speed: 189 kB/s
Done !!!
Writing file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ N7100_Rom1_Alive_Dump_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1608 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
eMMC CRC Error at addr:0x62c0
Writing file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ N7100_Rom1_Alive_Dump_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1629 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
eMMC CRC Error at addr:0x62c0
Writing file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ N7100_Rom1_Alive_Dump_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
Write Speed: 188 kB/s
Done !!!

[johntba]

hi again
when i am trying to write boot bin file i get the next error "eMMC ACK Error at addr:0x0"

Loading eMMC Addon Firmware...
CMD Pullup Level:1557 mV
CMD Active Level:2310 mV
EMMC CID 15010056545530304D009C0A6ABB8F2D
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 2617928379
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 00200000 bytes to 00000000 ...ROM2
eMMC ACK Error at addr:0x0

emmc card is readed and recognised.Why i can not write it?
I must give little more voltage when i write?
Any idea guys?

[johntba]

Dear Blang
i forgot to mention you that with reading emmc i have no problem or errors.everything is fine.Only when try to write is the problem.
Thank you

[mobilegsm30]

Originally Posted by johntba

Dear Blang
i forgot to mention you that with reading emmc i have no problem or errors.everything is fine.Only when try to write is the problem.
Thank you

Hello johntba i also face same problem. now is ok you have check GND need stronger.

[johntba]

thank you friend i will try a better ground on board

[blang]

Originally Posted by mobilegsm30

Hello Blang

After lots of try now write both files in n7100 but still not power on. only red light blink on top.


Resources ver. : MainRC ver.OCD040Z001 (C)2012 z3x-team.com
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2340 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
=============================================
Extended CSD rev 1.6 (MMC 4.5)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x01]:
implementation based on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Max Packet Read Cmd [MAX_PACKED_READS: 0x3f]
Max Packet Write Cmd [MAX_PACKED_WRITES: 0x3f]
Data TAG support [DATA_TAG_SUPPORT: 0x01]
Data TAG Unit Size [TAG_UNIT_SIZE: 0x04]
Tag Resources Size [TAG_RES_SIZE: 0x00]
Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]
Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]
Extended partition attribute support [EXT_SUPPORT: 0x03]
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x02]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x10]
Access size [ACC_SIZE: 0x07]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x50]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x01d5a000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x02]
I/O Driver Strength [DRIVER_STRENGTH: 0x00]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x48]
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x01]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0000bb
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Periodic Wake-up [PERIODIC_WAKEUP]: 0x00
Program CID/CSD in DDR mode support [PROGRAM_CID_CSD_DDR_SUPPORT]: 0x01
Native sector size [NATIVE_SECTOR_SIZE]: 0x00
Sector size emulation [USE_NATIVE_SECTOR]: 0x00
Sector size [DATA_SECTOR_SIZE]: 0x00
1st initialization after disabling sector size emulation [INI_TIMEOUT_EMU]: 0x00
Class 6 commands control [CLASS_6_CTRL]: 0x00
Number of addressed group to be Released[DYNCAP_NEEDED]: 0x00
Exception events control [EXCEPTION_EVENTS_CTRL]: 0x0000
Exception events status[EXCEPTION_EVENTS_STATUS]: 0x0000
Extended Partitions Attribute [EXT_PARTITIONS_ATTRIBUTE]: 0x0000
Packed command status [PACKED_COMMAND_STATUS]: 0x00
Packed command failure index [PACKED_FAILURE_INDEX]: 0x00
Power Off Notification [POWER_OFF_NOTIFICATION]: 0x00
Control to turn the Cache ON/OFF [CACHE_CTRL]: 0x00
Writing file...E:\EasyJtag\N7100\N7100_Rom2_Alive_Boot_BN\ N7100_Rom2_Alive_Boot_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2320 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 00100000 bytes to 00000000 ...ROM1
Write Speed: 189 kB/s
Done !!!
Writing file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ N7100_Rom1_Alive_Dump_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1608 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
eMMC CRC Error at addr:0x62c0
Writing file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ N7100_Rom1_Alive_Dump_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1629 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
eMMC CRC Error at addr:0x62c0
Writing file...E:\EasyJtag\N7100\N7100_Rom1_Alive_Dump_BN\ N7100_Rom1_Alive_Dump_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1619 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
Write Speed: 188 kB/s
Done !!!

But BOOT located in ROM2. you need flash rom2. only after this you can switch phone to download mode and flash. try this

[mobilegsm30]

Originally Posted by blang

But BOOT located in ROM2. you need flash rom2. only after this you can switch phone to download mode and flash. try this

Hello thanks for reply my phone now in download mode but small problem. phone shows product code GT-I9300 please check?


Z3X Card Version : 22
Z3X Card Activation [JTAG] : 1
Resources ver. : MainRC ver.OCD040Z001 (C)2012 z3x-team.com
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1629 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
=============================================
Extended CSD rev 1.6 (MMC 4.5)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x01]:
implementation based on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Max Packet Read Cmd [MAX_PACKED_READS: 0x3f]
Max Packet Write Cmd [MAX_PACKED_WRITES: 0x3f]
Data TAG support [DATA_TAG_SUPPORT: 0x01]
Data TAG Unit Size [TAG_UNIT_SIZE: 0x04]
Tag Resources Size [TAG_RES_SIZE: 0x00]
Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]
Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]
Extended partition attribute support [EXT_SUPPORT: 0x03]
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x02]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x10]
Access size [ACC_SIZE: 0x07]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x50]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x01d5a000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x02]
I/O Driver Strength [DRIVER_STRENGTH: 0x00]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x48]
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x01]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0000bb
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Periodic Wake-up [PERIODIC_WAKEUP]: 0x00
Program CID/CSD in DDR mode support [PROGRAM_CID_CSD_DDR_SUPPORT]: 0x01
Native sector size [NATIVE_SECTOR_SIZE]: 0x00
Sector size emulation [USE_NATIVE_SECTOR]: 0x00
Sector size [DATA_SECTOR_SIZE]: 0x00
1st initialization after disabling sector size emulation [INI_TIMEOUT_EMU]: 0x00
Class 6 commands control [CLASS_6_CTRL]: 0x00
Number of addressed group to be Released[DYNCAP_NEEDED]: 0x00
Exception events control [EXCEPTION_EVENTS_CTRL]: 0x0000
Exception events status[EXCEPTION_EVENTS_STATUS]: 0x0000
Extended Partitions Attribute [EXT_PARTITIONS_ATTRIBUTE]: 0x0000
Packed command status [PACKED_COMMAND_STATUS]: 0x00
Packed command failure index [PACKED_FAILURE_INDEX]: 0x00
Power Off Notification [POWER_OFF_NOTIFICATION]: 0x00
Control to turn the Cache ON/OFF [CACHE_CTRL]: 0x00
Writing file...E:\EasyJtag\N7100\N7100_Rom2_Alive_Boot_BN\ N7100_Rom2_Alive_Boot_BN.bin
Successefuly connected to box on COM144
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1608 mV
CMD Active Level:2330 mV
EMMC CID 15010056545530304D00433442B88F63
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 1127498424
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 00100000 bytes to 00000000 ...ROM2
Write Speed: 148 kB/s
Done !!!

[johntba]

hi guys.Now my ground is very good but still eMMC ACK Error at addr:0x0

Any idea someone?

[johntba]

hi again guys.Now my ground is super good but still the same

Loading eMMC Addon Firmware...
CMD Pullup Level:1536 mV
CMD Active Level:2258 mV
EMMC CID 15010056545530304D009C0A6ABB8F2D
EMMC CSD D02701320F5903FFF6DBFFFF8E40406D
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 08/2012 FW rev.0x0 HW rev.0x0
EMMC Serial #: 2617928379
EMMC NAME: VTU00M
EMMC Capacity: 15028 MB (High Density Card)
Writing 20000000 bytes to 00000000 ...ROM1
eMMC ACK Error at addr:0x0

Any idea someone?

[mobilegsm30]

Hello Blang

my phone N7100 repaired ok flashed ok imei repaired now phone working but only problem is product name I9300 on download mode.

[johntba]

hi mobilegsm
With bad ground you could read but now write?
Because mine can read but can not write.
Bland any idea?

[mobilegsm30]

Originally Posted by johntba

hi mobilegsm
With bad ground you could read but now write?
Because mine can read but can not write.
Bland any idea?

Hello johntba please wait for Blang reply, i have also I9300 witch have same problem read ok but not write. before phone product name blank now phone is dead i also waiting for that solution.