GSM Shop GSM Shop
GSM-Forum  

Welcome to the GSM-Forum forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
Only registered members may post questions, contact other members or search our database of over 8 million posts.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

If you have any problems with the registration process or your account login, please contact contact us .

Go Back   GSM-Forum > Product Support Sections > Hard/Software Products (official support) > Easy-Jtag / Easy-Jtag Plus

Easy-Jtag / Easy-Jtag Plus The official support section. You can ask here your question and get answer regarding using Easy-Jtag / Easy-Jtag Plus.

Reply
 
LinkBack Thread Tools Display Modes
Old 07-14-2019, 10:35   #1 (permalink)
Insane Poster
 
Join Date: Sep 2012
Location: Manila / Pilipinas
Posts: 72
Member: 1807389
Status: Offline
Thanks Meter: 29
help oppo a3s cph1803 dead


pls help me oppo a3s cph1803 after clear pin/gst/pass & android clear frp phone is dead plss help
  Reply With Quote
The Following User Says Thank You to elusyonado For This Useful Post:
Old 07-14-2019, 11:56   #2 (permalink)
No Life Poster
 
rico_deep's Avatar
 
Join Date: Jul 2005
Location: philippine
Posts: 1,113
Member: 159757
Status: Offline
Thanks Meter: 461
Donate money to this user
check isp components, Especially CLK resistor
  Reply With Quote
The Following User Says Thank You to rico_deep For This Useful Post:
Old 07-14-2019, 11:58   #3 (permalink)
No Life Poster
 
kothamamun's Avatar
 
Join Date: Apr 2016
Location: B A N G L A D E S H
Posts: 3,171
Member: 2556542
Status: Offline
Thanks Meter: 1,776
Quote:
Originally Posted by elusyonado View Post
pls help me oppo a3s cph1803 after clear pin/gst/pass & android clear frp phone is dead plss help
new experience for us oppo is not safe for unlock jtag
  Reply With Quote
The Following User Says Thank You to kothamamun For This Useful Post:
Old 08-16-2019, 03:40   #4 (permalink)
Crazy Poster
 
Join Date: Sep 2010
Location: iran
Posts: 51
Member: 1402783
Status: Offline
Thanks Meter: 5
for oppo 1803 reset oppo only

do not clear pin or frp clean
  Reply With Quote
The Following 3 Users Say Thank You to blancherd For This Useful Post:
Show/Hide list of the thanked
Old 08-31-2019, 03:20   #5 (permalink)
Junior Member
 
Join Date: Jul 2008
Location: philippines
Age: 45
Posts: 27
Member: 810891
Status: Offline
Sonork: 100.1625691
Thanks Meter: 5
did you revive the power ?
same here. after reset factory on UFI makes error and now its dead phone.

oppo A3s cph1803
  Reply With Quote
Old 09-02-2019, 13:28   #6 (permalink)
Freak Poster
 
patel yogesh's Avatar
 
Join Date: Feb 2016
Location: valsad
Posts: 126
Member: 2529129
Status: Offline
Thanks Meter: 56
i have same a3s cph1803
dead in easy jteq ...
  Reply With Quote
Old 10-04-2019, 11:56   #7 (permalink)
Major Poster
 
Join Date: Mar 2014
Location: Philippines
Posts: 40
Member: 2141040
Status: Offline
Thanks Meter: 17
same also , first time to also here is the logs

EasyJtag Suite Classic ver.: 3.6.1.4 / wxWidgets 3.1.2-W-U started.
OS ver.: Windows 10 (build 10586). Admin rights FAIL
Android Explorer ver:1.0.0.13
Autorun Agent ver:1.0.0.0
Crash Reporting ver:1.4.0.3
eMMC Odin ver:1.0.0.6
QUALCOMM Direct ver:1.0.6936.8894
Android ADB API ver:2.0.0.0
FTDI API ver:3.2.4.0
LibUSB API ver:1.2.6.0
Visual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 10.0.10586.306, are OK
Z3X Card Serial : AAA1-C5FB , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED


Found 5 serial devices
COM1 ACPI\VEN_PNP&DEV_0501 Communications Port (COM1)
COM3 Intel(R) Active Management Technology - SOL (COM3)
COM39 root\rimports RIM Virtual Serial Port v2 (COM39)
COM40 root\rimports RIM Virtual Serial Port v2 (COM40)
COM160 USB\VID_0325&PID_0032&REV_0100&MI_00 USB Serial Device (COM160)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.6.1.4
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0200300EC96F8F0A, ,FW Ver.: 01.63
CMD Pullup Level:2010 mV
CMD Active Level:1619 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 150100514536334D4206472A9ACFA578
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 10/2018 Rev.0x6
eMMC NAME: QE63MB , S/N: 1193974479
eMMC NAME (HEX): 514536334D42
IC Name: Samsung , KMQE60013M-B318/16GB @BGA221
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
RPMB Info mmc_init Error, Reason: CMD Timeout Error
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: QE63MB_1193974479_20191004_1523.extcsd
Done.

Z3X EasyJtag Software ver. 3.6.1.4
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0200300EC96F8F0A, ,FW Ver.: 01.63
CMD Pullup Level:2010 mV
CMD Active Level:2526 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 150100514536334D4206472A9ACFA578
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 10/2018 Rev.0x6
eMMC NAME: QE63MB , S/N: 1193974479
eMMC NAME (HEX): 514536334D42
IC Name: Samsung , KMQE60013M-B318/16GB @BGA221
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 27832 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: QE63MB_1193974479_20191004_1524.extcsd
Done.

Z3X EasyJtag Software ver. 3.6.1.4
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0200300EC96F8F0A, ,FW Ver.: 01.63
Warning: CMD Pullup Level (257 mV) too low , check cables etc.!
CMD Active Level:2536 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 150100514536334D4206472A9ACFA578
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 10/2018 Rev.0x6
eMMC NAME: QE63MB , S/N: 1193974479
eMMC NAME (HEX): 514536334D42
IC Name: Samsung , KMQE60013M-B318/16GB @BGA221
EMMC ROM1 (Main User Data) Capacity: 14910 MB , 0x1D1F000 pages , 0x3A3E00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 27832 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Partition table scan:
GPT: present
Found valid GPT with protective MBR; using GPT.
Real (Hardware) Disk/Image size: 1D1F000 sectors 14.6 GiB
Soft (Partitioned) Disk/Image size: 1D1EFBC sectors 14.6 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
First usable sector: 34
Last usable sector: 30535646
Partition info successfully found
------ Android information ------
Detected LINUX(Android) CACHE : 0x001FB00000 (256.0MB)
Erasing...
Done.
Detected LINUX(Android) USERDATA : 0x0158000000 (9.184GB)
Erasing...
Done.
---------------------------------------------
Done.

Running:Format FRP Partition...
Z3X EasyJtag Software ver. 3.6.1.4
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0200300EC96F8F0A, ,FW Ver.: 01.63
CMD Pullup Level:2021 mV
CMD Active Level:2547 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 150100514536334D4206472A9ACFA578
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 10/2018 Rev.0x6
eMMC NAME: QE63MB , S/N: 1193974479
eMMC NAME (HEX): 514536334D42
IC Name: Samsung , KMQE60013M-B318/16GB @BGA221
EMMC ROM1 (Main User Data) Capacity: 14910 MB , 0x1D1F000 pages , 0x3A3E00000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 27832 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Partition table scan:
GPT: present
Found valid GPT with protective MBR; using GPT.
Real (Hardware) Disk/Image size: 1D1F000 sectors 14.6 GiB
Soft (Partitioned) Disk/Image size: 1D1EFBC sectors 14.6 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
First usable sector: 34
Last usable sector: 30535646
Partition info successfully found
Formatting FRP...
Detected LINUX(Android) CACHE : 0x001FB00000 (256.0MB) , formatting...
Done.
Detected LINUX(Android) CONFIG : 0x002FC80000 (32.0KB) formatting...
Done.
Detected LINUX(Android) USERDATA : 0x0158000000 (9.184GB) , formatting...
Done.
Done.
Done.

please help me team
  Reply With Quote
Old 10-04-2019, 12:18   #8 (permalink)
No Life Poster
 
Join Date: Feb 2009
Location: inside apples a15
Posts: 885
Member: 975554
Status: Offline
Sonork: KG state:prenormal
Thanks Meter: 252
Donate money to this user
for this model dont use clear pin pass or frp use only format userdata..it will only send command to phone to factory reset it..done many times without dead..be very carefull also when removing shield mostly while removing the shield you already killed the device
  Reply With Quote
The Following User Says Thank You to simpleprince49 For This Useful Post:
Old 10-08-2019, 08:50   #9 (permalink)
Freak Poster
 
Join Date: Dec 2017
Location: Dar es salaam,Tanzania
Posts: 110
Member: 2790329
Status: Offline
Thanks Meter: 27
If you connect device to computer and show 9008 port,you need to looo click resistor.solved many times

Sent from my Redmi Note 4 using Tapatalk
  Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 



All times are GMT +1. The time now is 14:42.



Powered by Searchlight © 2024 Axivo Inc.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -
Page generated in 0.16507 seconds with 8 queries

SEO by vBSEO