how full earse emmc - GSM-Forum

morteza-matin · 08-07-2016, 12:27

i have i9082 that change emmc but before me work in phone
how full erase emmc ?and after full erase which file respectivetly write in the phone
after repair direct emmc, phone go to download mode or after repair emmc repeat repair via j-tag tool?

thanks

Jani-Jan · 08-07-2016, 12:32

I think no need to erase emmc.just write boot partitions and rom1.after that flash with odin.

morteza-matin · 08-07-2016, 12:50

please upload file that tested

morteza-matin · 08-07-2016, 13:06

any body help ,how full erase emmc ?

Jani-Jan · 08-07-2016, 13:17

Why you need to erase?

morteza-matin · 08-07-2016, 15:55

Z3X EasyJtag Software ver. 2.3.0.0
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: 06FF801264EDB6C0, ,FW Ver.: 01.55CMD Pullup Level:1680 mV
CMD Active Level:1753 mV
Box IO Level:1800 mV
CLK Rate:14000 khz
HiPower mode is ON!
---------- eMMC Device Information ----------EMMC CID : 1501004D38473157410A9357618021DA
EMMC CSD : D02701320F5903FFF6DBFFE18E404028
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 02/2014 Rev.0xA
EMMC NAME: M8G1WA , S/N: 2471977344
EMMC NAME (HEX): 4D384731574100
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: M8G1WA_2471977344_20160807_1923.extcsd
Done.

here is log emmc ,please help me

morteza-matin · 08-07-2016, 19:25

Data partitions (firmware parts) count is 128 (dec)
mmc_read_blocks(D1FFFE00 > D2000000 ), Read address is invalid
mmc_read_blocks(D1FFBE00 > D2000000 ), Read address is invalid
Meta partitions (partitions storing partition table) count is 1 (dec)
Partitions are not found!

Jani-Jan · 08-08-2016, 12:38

Update emmc firmware.

08-07-2016, 12:27	#1 (permalink)
morteza-matin No Life Poster Join Date: Apr 2008 Location: iran-tehran Age: 41 Posts: 503 Member: 742476 Status: Offline Thanks Meter: 40	how full earse emmc i have i9082 that change emmc but before me work in phone how full erase emmc ?and after full erase which file respectivetly write in the phone after repair direct emmc, phone go to download mode or after repair emmc repeat repair via j-tag tool? thanks

08-07-2016, 12:32	#2 (permalink)
Jani-Jan No Life Poster Join Date: Jan 2003 Location: GMT +5 Age: 49 Posts: 1,230 Member: 19737 Status: Offline Thanks Meter: 133	I think no need to erase emmc.just write boot partitions and rom1.after that flash with odin.

08-07-2016, 12:50	#3 (permalink)
morteza-matin No Life Poster Join Date: Apr 2008 Location: iran-tehran Age: 41 Posts: 503 Member: 742476 Status: Offline Thanks Meter: 40	please upload file that tested

08-07-2016, 13:06	#4 (permalink)
morteza-matin No Life Poster Join Date: Apr 2008 Location: iran-tehran Age: 41 Posts: 503 Member: 742476 Status: Offline Thanks Meter: 40	any body help ,how full erase emmc ?

08-07-2016, 13:17	#5 (permalink)
Jani-Jan No Life Poster Join Date: Jan 2003 Location: GMT +5 Age: 49 Posts: 1,230 Member: 19737 Status: Offline Thanks Meter: 133	Why you need to erase?

08-07-2016, 15:55	#6 (permalink)
morteza-matin No Life Poster Join Date: Apr 2008 Location: iran-tehran Age: 41 Posts: 503 Member: 742476 Status: Offline Thanks Meter: 40	Z3X EasyJtag Software ver. 2.3.0.0 Loading eMMC Addon Firmware... IO: 1800 mV Box S/N: 06FF801264EDB6C0, ,FW Ver.: 01.55CMD Pullup Level:1680 mV CMD Active Level:1753 mV Box IO Level:1800 mV CLK Rate:14000 khz HiPower mode is ON! ---------- eMMC Device Information ----------EMMC CID : 1501004D38473157410A9357618021DA EMMC CSD : D02701320F5903FFF6DBFFE18E404028 EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 02/2014 Rev.0xA EMMC NAME: M8G1WA , S/N: 2471977344 EMMC NAME (HEX): 4D384731574100 EMMC ROM1 (Main User Data) Capacity: 7456 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 0 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: No Extended CSD rev 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x00. H/W reset function [RST_N_FUNCTION]: 0x01 High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000] Partitioning Support [PARTITIONING_SUPPORT]: 0x03 Device support partitioning feature Device can have enhanced tech. Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00 --------------------------------------------- Backup saved: M8G1WA_2471977344_20160807_1923.extcsd Done. here is log emmc ,please help me

08-07-2016, 19:25	#7 (permalink)
morteza-matin No Life Poster Join Date: Apr 2008 Location: iran-tehran Age: 41 Posts: 503 Member: 742476 Status: Offline Thanks Meter: 40	Data partitions (firmware parts) count is 128 (dec) mmc_read_blocks(D1FFFE00 > D2000000 ), Read address is invalid mmc_read_blocks(D1FFBE00 > D2000000 ), Read address is invalid Meta partitions (partitions storing partition table) count is 1 (dec) Partitions are not found!

08-08-2016, 12:38	#8 (permalink)
Jani-Jan No Life Poster Join Date: Jan 2003 Location: GMT +5 Age: 49 Posts: 1,230 Member: 19737 Status: Offline Thanks Meter: 133	Update emmc firmware.