HTC Desire 516 Connection Problem!

[MiRoOo]

Hello guys,

Just got one HTC Desire 516 which has dead bootloader (9008),
I've downloaded 1GB dump from shell, And got the pinout from another thread (Here),
I did exactly as the pinout, but there is a connection problem,
Check the log:

Z3X EasyJtag Software ver. 2.1.0.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: ------------------, ,FW Ver.: 01.54
CMD Pullup Level:2062 mV
CMD Active Level:2361 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 90014A4834473164040502A1AEF3812C
EMMC CSD : D02701320F5903FFFFFFFFEF8A4040D2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 08/2014 Rev.0x5
EMMC NAME: H4G1d , S/N: 44150515
EMMC NAME (HEX): 48344731642000
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.

I've checked the D0 line, and it's soldered just fine,
So, what is the problem!?,

Thanks in advance

[omi17]

Originally Posted by MiRoOo

Hello guys,

Just got one HTC Desire 516 which has dead bootloader (9008),
I've downloaded 1GB dump from shell, And got the pinout from another thread (Here),
I did exactly as the pinout, but there is a connection problem,
Check the log:



I've checked the D0 line, and it's soldered just fine,
So, what is the problem!?,

Thanks in advance

Same problem any suggestions

[MiRoOo]

Originally Posted by omi17

Same problem any suggestions

No, but i'm working on a solution for boot repair with USB only right now,
Once i finished i'm going to make a full guide for how to do it,

Best Regards


Sent from my iPhone 6 using Tapatalk.

[umarmsn]

Originally Posted by omi17

its good then
waiting for you

i have also same problem if done pls guide me

[shamsulhaq]

connect only atf box

[ALI_MAFIA]

use puul up volt problem will be solv

[ALI_MAFIA]

use puul up volt problem will be solv

[ISolutions]

same problem mine also after pull up resister also problem

[umarmsn]

Originally Posted by ISolutions

same problem mine also after pull up resister also problem

yes i accept

same problem after pull up resister

[alexjuve42]

the data0 under cpu

[rohit.sharma73]

Plzz give desire 516 dumb file link plzzzzzzzzzzzz

[laxmi kamlesh]

Originally Posted by rohit.sharma73

Plzz give desire 516 dumb file link plzzzzzzzzzzzz

Why you need ?

have you connected ?

HTC 516h dual Don't have data 0 point on Board.

so you can't repair it via ISP.

you can repair it via remove emmc and program.

Device Brand : htc
Device Manufact.: HTC
Device Model : htc_v2_dug
Device CPU : MSM8610
Device IntName : htc_asia_india
Device Version : 4.3
CU_SWVer : HTC
Device Compile : 14/08/2014 4:12:59 PM
Device ExtInfo : HTC Desire 516 dual sim

[TUN10]

Originally Posted by MiRoOo

No, but i'm working on a solution for boot repair with USB only right now,
Once i finished i'm going to make a full guide for how to do it,

Best Regards


Sent from my iPhone 6 using Tapatalk.

Hello is there any news about repaiar boot by usb.

I fined solution here but cant enter phone in Qualcomm HS-USB QDLoader 9006 mode

do Youi know any solution

THANKS

[sujay dutta]

[yuvraj9x2]

Originally Posted by MiRoOo

Hello guys,

Just got one HTC Desire 516 which has dead bootloader (9008),
I've downloaded 1GB dump from shell, And got the pinout from another thread (Here),
I did exactly as the pinout, but there is a connection problem,
Check the log:



I've checked the D0 line, and it's soldered just fine,
So, what is the problem!?,

Thanks in advance

LinkShrink.net - Earn money sharing shrinked links!

WORKING pinout