i8730 support PLEASE - GSM-Forum

rikimaer · 05-28-2014, 15:55

Get connected as i9505 but wich file and how i should write on the emmc?

Thanks
Best Regards

Warning , you are using custom pinout config make shure that NRST and GND on proper places!
EasyJtag Suite ver.: 1.5.1.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7600).

For support and updates visit EasyJtag ? most powerfull eMMC and JTAG tool on market. - The best eMMC and JTAG service solution. Total repair and forensics tool for Android devices!
Check security...OK
Initialising: SAMSUNG GT-I9505 Config ver.:1.01
I/O Level set to : 2200 mV
Box S/N: 10100416241CBA99 ,FW Ver.: 01.50
Connecting to Target...
Halting CPU...
Initialize hardware...
Starting target communication...
KNOX WARRANTY VOID: 0
Detecting emmc memory parameters of bank (0) ...
EMMC #0 : ID : 0x00000045 Name : SEM08G Size : 7.3 G , (15269888) Blocks
EMMC #1 : ID : 0x00000045 Name : SEM08G Size : 2.0 M , (4096) Blocks
eMMC flash device(s) found, Device ID : 0x00450000
Reading dump to file...C:\Users\Jose\Desktop\SAMSUNG_GT-I9505_0x00000000_0x00200000.bin
Reading 0x000000200000 bytes from emmc adress 0x000000000000
Dumped 2097152 bytes in 9.065518s (225.911 KiB/s) OK.

rikimaer · 05-28-2014, 15:56

Now as I9190 gets CPU

Code:

For support and updates visit http://easy-jtag.com
Check security...OK
Initialising: SAMSUNG GT-I9195 Config ver.:1.00
I/O Level set to : 2200 mV
Box S/N: 10100416241CBA99 ,FW Ver.: 01.50
Connecting to Target...
JTAG device: MSM8930AB. 
CPU IDCODE : 0x4F1F0F0F Mfg.: 0x787, Part: 0xf1f0, Ver.: 0x4
CPU Manufacturer: Samsung , CPU Name: ARM7GEN
JTAG device: MSM8930AB. 
CPU IDCODE : 0x207230E1 Mfg.: 0x070, Part: 0x0723, Ver.: 0x2
CPU Manufacturer: QUALCOMM , CPU Name: Unknown
Halting CPU...
Initialize hardware...
Starting target communication...
Detecting emmc memory parameters of bank (0) ...
EMMC #0 : ID : 0x00000045 Name : SEM08G Size : 7.3 G , (15269888) Blocks
EMMC #1 : ID : 0x00000045 Name : SEM08G Size : 2.0 M , (4096) Blocks
eMMC flash device(s) found, Device ID : 0x00450000

**blang** · 05-28-2014, 16:09

need dump from working phone + hi quality pcb photo.

debeliamark · 10-17-2015, 14:38

Here you can find a eMMC connection in case of needs:

For full dump - write me a message, please.

WBR, DebeliaMark, BG

debeliamark · 10-17-2015, 15:03

P.S.

What mean

Code:

Z3X EasyJtag Software ver. 2.0.5.0
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: 0C0C0313F73xxxx8, ,FW Ver.: 01.52
CMD Pullup Level:2640 mV
CMD Active Level:2351 mV
eMMC Device Information
EMMC CID : 02000053444D30333290FFFFFFFF29BC
EMMC CSD : 8C0F002A015981E9B6D9FC1F8A4040AA
EMMC Manufacturer ID: 0002 , OEM ID: 0000
EMMC Date: 02/2006 Rev.0x90
EMMC NAME: SDM032 , S/N: 4294967295
EMMC NAME (HEX): 53444D30333200 
EMMC ROM1 (Main User Data) Capacity: 30 MB
EMMC ROM2 (Boot Partition 1) Capacity: 0 kB
EMMC ROM3 (Boot Partition 2) Capacity: 0 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.0 (MMC 4.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: SDM032_4294967295_20150906_1701.extcsd
Done.

Only 30MB ROM1 size ? Dead eMMC ?

A third time i face this in SanDisk eMMC IC-s.

algerienbox · 10-10-2017, 15:46

try write by vendor..........

eumore79 · 11-11-2017, 06:28

try this pinout
what is vddi? is this clk pinout?

where is that vccq pin connect?

05-28-2014, 15:55	#1 (permalink)
rikimaer Freak Poster Join Date: May 2004 Location: spain Age: 35 Posts: 141 Member: 65061 Status: Offline Thanks Meter: 30	i8730 support PLEASE Get connected as i9505 but wich file and how i should write on the emmc? Thanks Best Regards Warning , you are using custom pinout config make shure that NRST and GND on proper places! EasyJtag Suite ver.: 1.5.1.0 / wxWidgets 3.1.0-W-U started. Operating system ver.: Windows 7 (build 7600). For support and updates visit EasyJtag ? most powerfull eMMC and JTAG tool on market. - The best eMMC and JTAG service solution. Total repair and forensics tool for Android devices! Check security...OK Initialising: SAMSUNG GT-I9505 Config ver.:1.01 I/O Level set to : 2200 mV Box S/N: 10100416241CBA99 ,FW Ver.: 01.50 Connecting to Target... Halting CPU... Initialize hardware... Starting target communication... KNOX WARRANTY VOID: 0 Detecting emmc memory parameters of bank (0) ... EMMC #0 : ID : 0x00000045 Name : SEM08G Size : 7.3 G , (15269888) Blocks EMMC #1 : ID : 0x00000045 Name : SEM08G Size : 2.0 M , (4096) Blocks eMMC flash device(s) found, Device ID : 0x00450000 Reading dump to file...C:\Users\Jose\Desktop\SAMSUNG_GT-I9505_0x00000000_0x00200000.bin Reading 0x000000200000 bytes from emmc adress 0x000000000000 Dumped 2097152 bytes in 9.065518s (225.911 KiB/s) OK.

10-17-2015, 14:38	#4 (permalink)
debeliamark No Life Poster Join Date: May 2001 Location: Bulgaria Age: 56 Posts: 4,796 Member: 4627 Status: Offline Sonork: 57528:debeliamark Thanks Meter: 1,034	GT-i8730 eMMC connection Here you can find a eMMC connection in case of needs: For full dump - write me a message, please. WBR, DebeliaMark, BG

05-28-2014, 16:09	#3 (permalink)
blang Product Manager Join Date: Oct 2000 Location: future Posts: 22,431 Member: 2368 Status: Offline Sonork: 100.111111 Thanks Meter: 186,554	need dump from working phone + hi quality pcb photo.

10-10-2017, 15:46	#6 (permalink)
algerienbox No Life Poster Join Date: Sep 2007 Location: algeria Posts: 2,360 Member: 591880 Status: Offline Thanks Meter: 561	try write by vendor..........

11-11-2017, 06:28	#7 (permalink)
eumore79 No Life Poster Join Date: Jun 2007 Location: Negros, Philippines Posts: 1,170 Member: 525940 Status: Offline Thanks Meter: 213	try this pinout what is vddi? is this clk pinout? where is that vccq pin connect?