GSM Shop GSM Shop
GSM-Forum  

Welcome to the GSM-Forum forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
Only registered members may post questions, contact other members or search our database of over 8 million posts.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

If you have any problems with the registration process or your account login, please contact contact us .

Go Back   GSM-Forum > Product Support Sections > Hard/Software Products (official support) > Easy-Jtag / Easy-Jtag Plus

Easy-Jtag / Easy-Jtag Plus The official support section. You can ask here your question and get answer regarding using Easy-Jtag / Easy-Jtag Plus.

Reply
 
LinkBack Thread Tools Display Modes
Old 01-14-2020, 19:19   #1 (permalink)
No Life Poster
 
Join Date: Oct 2007
Location: EGYPT
Posts: 3,804
Member: 601566
Status: Offline
Sonork: 100.1637134
Thanks Meter: 551
LS777ZVG died


phone after write carrier and modem died
ual C++ Runtime ver:10.0.30319.1
Setting box Pinout ...

Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA63-6424 , ver: 22
Z3X Card Activation [JTAGPLUS] : NOT ACTIVATED
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : NOT ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED


Found 2 serial devices
COM32 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM32)
COM4 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM4)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.6.2.0
Loading eMMC GEN1 Firmware... IO: 3300 mV
Box S/N: 10FFE00C1DB260E5, ,FW Ver.: 01.63
CMD Pullup Level:2052 mV
CMD Active Level:3073 mV
Box IO Level:3300 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------

eMMC CID : 150100514536334D420311C7964C55F8
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2018 Rev.0x3
eMMC NAME: QE63MB , S/N: 298292812
eMMC NAME (HEX): 514536334D42
IC Name: Samsung , KMQE60013M-B318/16GB @BGA221
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is programmed and written 396 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: QE63MB_ 298292812_20200114_0904.extcsd
Caution: invalid main GPT header, but valid a backup header!
Warning: Invalid CRC on main header data; loaded backup partition table.
EFI Table CRC Check FAIL.
Warning! Main partition table CRC mismatch! Loaded backup
Warning! One or more CRCs don't match. You should repair the disk!
Real (Hardware) Disk/Image size: 1D1F000 sectors 14.6 GiB
Soft (Partitioned) Disk/Image size: 1D1EFDE sectors 14.6 GiB
Disk identifier (GUID): 001E001D-001F-0020-2100-220023002400
Logical sector size: 0x200 bytes ,First/Last usable sector: 17,30535663
Partition info successfully found
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x001F800000 (3.625GB)
Short EXT fs info:
Size: 3.568GB
Block size: 4.0KB
Inode size: 256
Inodes: 234320
Short Android info:
Build ID: NRD90U
Display Build ID: NRD90U
Release Incremental ID: 1830510094c4a
Release Base ID: 7.0
Security Path: 2018-11-01
Device Model: LG-LS777
Device Manufacturer: lge
Device Name A: sf340_spr_us
Device Name B: sf340
Device Board Name: msm8937_32
Architecture ABI: armeabi-v7a
Device manufacturer: LGE
Device Platform: msm8937
Product ID: sf340
Build Description: sf340_spr_us-user 7.0 NRD90U 1830510094c4a release-keys
Target Carrier: SPR
Target Country: US
FRP Partition Path: /dev/block/bootdevice/by-name/persistent
LGE SW Version: LS777ZVG
LGE SW Version Short: ZVG
LGE SW Revision: 00
LGE SW Version: LGLS777AT-00-ZVG-SPR-US-NOV-01-2018-ARB02+00
Backup saved: BuildProp_20200114_0904.txt
  Reply With Quote
Old 01-16-2020, 04:47   #2 (permalink)
Crazy Poster
 
Join Date: May 2016
Location: Havana city, Cuba
Posts: 51
Member: 2577517
Status: Offline
Sonork: 100.1681425
Thanks Meter: 16
If you only write modem and carrier partitions for unlock no posiblities of brick.
You must check the components where you soldered, check clk resistor (must be shorted) and cmd resistor (10kohms)
  Reply With Quote
Old 01-17-2020, 00:38   #3 (permalink)
No Life Poster
 
Join Date: Oct 2007
Location: EGYPT
Posts: 3,804
Member: 601566
Status: Offline
Sonork: 100.1637134
Thanks Meter: 551
i write write modem and carrier in userdata imag now only qualcomm
  Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 



All times are GMT +1. The time now is 21:23.



Powered by Searchlight © 2024 Axivo Inc.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -
Page generated in 0.11011 seconds with 8 queries

SEO by vBSEO