New To Easy Jtag

[neo_49]

Last month i bought Easy Jtag and try to connect two board (J500F & D325 ) last week but not succeeded with EJ same set repair with other box (LG D325 only ) .Sorry i dont have log now & just want to check my adaptor & box .

Is it possible to have diode mode value for box pinout ?

Regards

[royalnasim]

Post your adpater pic

[neo_49]

Originally Posted by royalnasim

Post your adpater pic

This is my adapter & allways getting error like
(Can't init device, Reason: CMD Timeout Error,
Warning: CMD Pullup Level (134 mV) too low , check cables etc.! ,
Can't init EMMC, Reason: CARD Data FIFO Timeout Error )

Regard

[neo_49]

Just checked that i am getting 2.6v out from CMD, CLK & DATA0 without any adapter direct from the box .(from my other box i get 2.2v from cmd & data0 only )

Regards

[blang]

Originally Posted by neo_49

Just checked that i am getting 2.6v out from CMD, CLK & DATA0 without any adapter direct from the box .(from my other box i get 2.2v from cmd & data0 only )

Regards

there are on sticked threads exist adapter picture and you can compare lines.

[neo_49]

Originally Posted by blang

there are on sticked threads exist adapter picture and you can compare lines.

Thanks , can you link me the thread for box pin-out comparison ?

Regards

[blang]

Originally Posted by neo_49

Thanks , can you link me the thread for box pin-out comparison ?

Regards

http://forum.gsmhosting.com/vbb/f672...nnect-1691327/

[neo_49]

If i am getting error without adapter or mobile connected is it wrong or its normal ?
Compression is ON
Z3X EasyJtag Software ver. 2.6.0.1
Loading eMMC GEN1 Firmware... IO: 3300 mV
Box S/N: xxxxxxxxxxxxx, ,FW Ver.: 01.60
CMD Pullup Level:3145 mV
CMD Active Level:3227 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
Can't init device, Reason: CMD Timeout Error
Done.

Regards

[neo_49]

Please help me same pinout same phone connecting with other box without any problem .
Regards

[neo_49]

Hi , now after using atf adapter for VCC & VCCQ & dat0,cmd & clk direct to box i m getting some info with error & again same time working with other box.

Compression is ON
Z3X EasyJtag Software ver. 2.6.0.1
Loading eMMC GEN1 Firmware... IO: 1850 mV
Box S/N: *************, ,FW Ver.: 01.60
CMD Pullup Level:1691 mV
CMD Active Level:1794 mV
Box IO Level:1850 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 45010053454D33324707003B7ABDD00E
EMMC CSD : D00F00320F5903FFFFFFFFFF8A40407E
EMMC Manufacturer ID: 0045 , OEM ID: 0100
EMMC Date: 13/2013 Rev.0x7
EMMC NAME: SEM32G , S/N: 3898045
EMMC NAME (HEX): 53454D33324700
Can't init EMMC, Reason: CARD Data FIFO Timeout Error
Check Data Line!
Done.

Regards

[Pijush Das]

Check DATA0 Line Only For Can't init EMMC, Reason: CARD Data FIFO Timeout Error

[neo_49]

Originally Posted by Pijush Das

Check DATA0 Line Only For Can't init EMMC, Reason: CARD Data FIFO Timeout Error

Thanks but where should i look inside box ? because connection working with other box .

Regards

[Pijush Das]

Originally Posted by neo_49

Thanks but where should i look inside box ? because connection working with other box .

Regards

Use Correct Adapter for perfect connection...

[neo_49]

May be i should wait for EJ Plus new hardware upgrade kit .

[royalnasim]

Originally Posted by neo_49

This is my adapter & allways getting error like
(Can't init device, Reason: CMD Timeout Error,
Warning: CMD Pullup Level (134 mV) too low , check cables etc.! ,
Can't init EMMC, Reason: CARD Data FIFO Timeout Error )

Regard

Just remove riff Emmc in socket and try again 100% solve your problem