samsung j100h emmc repaire done with jtag - Page 8 - GSM-Forum

gsmmithun · 10-02-2018, 13:18

BRO I CHEEK ALL FREQUENCY BUT NOT DONE AFTER change software

anjuman · 10-03-2018, 13:48

all done but device still dead any solution.

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 2097 mV
CMD Active Level: 2602 mV
EMMC Device Information :
EMMC CID: 90014A483447326211010DD8404432DD
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_0DD84044_20181003_180700.extcsd
EMMC Init completed.

Operation: Write all eMMC Regions at once

Writing BootConfig ...
Reg: 179 Value: 0x08
Reg: 177 Value: 0x00
Reg: 162 Value: 0x00
Done

Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000
Filename: EMMC_ROM2_00000000_00400000.bin
eMMC switching to ROM2
Writing partition...
Done writing partition. Write speed: 701.77 KB/s

Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000
Filename: EMMC_ROM3_00000000_00400000.bin
eMMC switching to ROM3
Writing partition...
Done writing partition. Write speed: 703.94 KB/s

Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000
Filename: EMMC_ROM1_00000000_20000000.bin
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 1793.76 KB/s

All done time: [00:05:06:287]

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 2097 mV
CMD Active Level: 2603 mV
EMMC Device Information :
EMMC CID: 90014A483447326211010DD8404432DD
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_0DD84044_20181003_181233.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000
Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000
Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000
Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000
Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000
Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000
Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000
Partition: MODEM, [000001000000 - 000001800000], size: 000000800000
Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000
Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000
Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000
Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000
Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000
Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000
Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000
Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000
Partition: efs, [000002B00000 - 000003F00000], size: 000001400000
Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000
Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000
Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000
Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000
Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000
Partition: system, [000012D00000 - 000053D00000], size: 000041000000
Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000
Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000
GPT header successfully parsed

Get firmware version

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 2097 mV
CMD Active Level: 2607 mV
EMMC Device Information :
EMMC CID: 90014A483447326211010DD8404432DD
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_0DD84044_20181003_181617.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000
Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000
Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000
Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000
Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000
Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000
Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000
Partition: MODEM, [000001000000 - 000001800000], size: 000000800000
Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000
Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000
Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000
Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000
Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000
Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000
Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000
Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000
Partition: efs, [000002B00000 - 000003F00000], size: 000001400000
Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000
Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000
Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000
Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000
Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000
Partition: system, [000012D00000 - 000053D00000], size: 000041000000
Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000
Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000
GPT header successfully parsed

Get firmware version

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 2094 mV
CMD Active Level: 2607 mV
EMMC Device Information :
EMMC CID: 90014A483447326211010DD8404432DD
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_0DD84044_20181003_181625.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000
Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000
Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000
Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000
Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000
Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000
Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000
Partition: MODEM, [000001000000 - 000001800000], size: 000000800000
Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000
Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000
Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000
Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000
Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000
Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000
Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000
Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000
Partition: efs, [000002B00000 - 000003F00000], size: 000001400000
Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000
Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000
Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000
Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000
Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000
Partition: system, [000012D00000 - 000053D00000], size: 000041000000
Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000
Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000
GPT header successfully parsed

Get firmware version

anjuman · 10-03-2018, 14:30

again done but still dead

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PIT at address: 000000004400
GPT-partitioning done

Unpacking file: spl.img
Unpacking file: sboot.bin
Unpacking file: sboot2.bin
Unpacking file: sprddsp.img
Unpacking file: sprdcp.img
Unpacking file: param.lfs
Unpacking file: boot.img
Unpacking file: recovery.img
Unpacking file: cache.img
Unpacking file: system.img
Unpacking file: hidden.img

Partition name: BOOT
Filename: spl.img , Offset: 000000000000 , filesize: 32768 bytes
eMMC switching to ROM2
Erasing partition...
Writing partition...
Done writing partition. Write speed: 485.80 KB/s
Partition name: SBOOT
Filename: sboot.bin , Offset: 000000400000 , filesize: 1573888 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1753.72 KB/s
Partition name: SBOOT2
Filename: sboot2.bin , Offset: 000000600000 , filesize: 1573888 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1745.65 KB/s
Partition name: WDSP
Filename: sprddsp.img , Offset: 000000C00000 , filesize: 1967104 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1740.28 KB/s
Partition name: MODEM
Filename: sprdcp.img , Offset: 000001000000 , filesize: 7391600 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1777.16 KB/s
Partition name: PARAM
Filename: param.lfs , Offset: 000002900000 , filesize: 634880 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1586.28 KB/s
Partition name: KERNEL
Filename: boot.img , Offset: 000004500000 , filesize: 5696512 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1775.04 KB/s
Partition name: RECOVERY
Filename: recovery.img , Offset: 000005500000 , filesize: 7033856 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Done writing partition. Write speed: 1779.29 KB/s
Partition name: CSC
Filename: cache.img , Offset: 000006500000 , filesize: 9834768 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 15
Done writing partition. Write speed: 1748.26 KB/s
Partition name: SYSTEM
Filename: system.img , Offset: 000012D00000 , filesize: 978769712 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 1649
Done writing partition. Write speed: 1740.57 KB/s
Partition name: HIDDEN
Filename: hidden.img , Offset: 000053D00000 , filesize: 14807536 bytes
eMMC switching to ROM1
Erasing partition...
Writing partition...
Sparse image found v.1.0 Total chunks: 29
Done writing partition. Write speed: 1728.23 KB/s

All done time: [00:11:03:128]

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 2078 mV
CMD Active Level: 2603 mV
EMMC Device Information :
EMMC CID: 90014A483447326211010DD8404432DD
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_0DD84044_20181003_185655.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: sboot, [000000400000 - 000000600000], size: 000000200000
Partition: sboot2, [000000600000 - 000000800000], size: 000000200000
Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000
Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000
Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000
Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000
Partition: wdsp, [000000C00000 - 000001000000], size: 000000400000
Partition: modem, [000001000000 - 000001800000], size: 000000800000
Partition: modem2, [000001800000 - 000002000000], size: 000000800000
Partition: tddsp, [000002000000 - 000002400000], size: 000000400000
Partition: fota_sig, [000002400000 - 000002500000], size: 000000100000
Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000
Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000
Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000
Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000
Partition: param, [000002900000 - 000002B00000], size: 000000200000
Partition: efs, [000002B00000 - 000003F00000], size: 000001400000
Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000
Partition: reserved2, [000004400000 - 000004500000], size: 000000100000
Partition: kernel, [000004500000 - 000005500000], size: 000001000000
Partition: recovery, [000005500000 - 000006500000], size: 000001000000
Partition: csc, [000006500000 - 000012D00000], size: 00000C800000
Partition: system, [000012D00000 - 000053D00000], size: 000041000000
Partition: hidden, [000053D00000 - 000056500000], size: 000002800000
Partition: userdata, [000056500000 - 0000E8FFBE00], size: 000092AFBE00
GPT header successfully parsed

Get firmware version

Brand = samsung
Manufacturer = samsung
Model = SM-J100H
Phone platform = sc8830
CPU Abi = armeabi-v7a
Android release = 4.4.4
Firmware version = KTU84P.J100HDDU0API1
Firmware date = Mon Sep 5 18:00:10 KST 2016

anjuman · 10-04-2018, 13:00

its done friends..i just put it with battery and jig insert..after ten minutes when i check device there is download mode...i restart its hang on logo ..now device ok working fine ...after format in recovery mode..thanks friends and easy jtag team.

anjuman · 10-04-2018, 17:24

another device done now its j100ml

eMMC_tool Suite ver. 1.4.9.0 (release date: 12.12.2017)
Microsoft Windows 7 (32 bit) build 7601 (6.1.7601.18015)

Looking for EasyJTAG box...
EasyJTAG API ver. 2022
EasyJTAG Box Serial = C339612C47832EE2
Card Serial = AADF-A9ED
EasyJTAG Box Firmware = 2.30

Changelog:

12.12.2017 (ver 1.4.9.0)
Fix: Bugs that have been found through your crash report
Fix: RandomVerify function
Fix: Creation of GPT for Samsung (write by vendor)
Fix: Failed to mount large Fat partitions (explorer)
Fix: Extraction from contact2.db (explorer)
Fix: Error in the "build.prop" parser
Fix: CID Parser
Add: Support for EasyJtag Plus Box
Add: Path for TempDir and InitialDir (option in settings)
Add: Unpack Lenovo QSB (utilities)
Add: Selecting a PIT file from CSC (write by vendor Samsung)
Add: Detect for encrypted dumps from GPG Box
Add: Detect for FullDiskEncryption Partition (explorer)
Add: LinearVerify of the Partition (read by vendor)
Add: Information base about emmc compatibility (thanks to phonemicrodb)
Add: Resizing the window (for small screen resolutions)
Add: Converting large partitions in SparseImage when reading by vendor (option in settings)
Add: Mounting SparseImage (explorer)
Add: Automatic backup of the EFS partition for Samsung (read by vendor)
Add: Formatting of EFS partition for Samsung on request (write by vendor)

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1765 mV
CMD Active Level: 1860 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_C73061F1_20181004_213435.extcsd
EMMC Init completed.

Scanning soft partitions
Partition table not found

Get firmware version
Firmware info not found

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1765 mV
CMD Active Level: 1859 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_C73061F1_20181004_213533.extcsd
EMMC Init completed.

Operation: Universal Factory Format
Please, wait ...

Successfully

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1765 mV
CMD Active Level: 1859 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_C73061F1_20181004_213554.extcsd
EMMC Init completed.

Operation: Changing GP sizes (test mode) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0

Successfully

Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] to cancel the changes

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1763 mV
CMD Active Level: 1859 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_C73061F1_20181004_213601.extcsd
EMMC Init completed.

Operation: Changing GP sizes (final write) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0

Successfully

Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] to finalize operation

After reconnect, make sure that the size of ROM1 has been changed.

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1765 mV
CMD Active Level: 1860 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_C73061F1_20181004_213622.extcsd
EMMC Init completed.

Scanning soft partitions
Partition table not found

Get firmware version
Firmware info not found

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1765 mV
CMD Active Level: 1859 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_C73061F1_20181004_213729.extcsd
EMMC Init completed.

Operation: Write all eMMC Regions at once

Writing BootConfig ...
Reg: 179 Value: 0x08
Reg: 177 Value: 0x00
Reg: 162 Value: 0x00
Done

Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000
Filename: EMMC_ROM2_H4G2b_827544235_00000000_00400000.bin
eMMC switching to ROM2
Writing partition...
Done writing partition. Write speed: 696.26 KB/s

Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000
Filename: EMMC_ROM3_H4G2b_827544235_00000000_00400000.bin
eMMC switching to ROM3
Writing partition...
Done writing partition. Write speed: 695.15 KB/s

Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000
Filename: EMMC_ROM1_H4G2b_827544235_00000000_20000000.bin
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 1783.39 KB/s

All done time: [00:05:08:183]

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 18 Mhz
CMD Pullup Level: 1766 mV
CMD Active Level: 1857 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101C73061F15243
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_C73061F1_20181004_214334.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000
Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000
Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000
Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000
Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000
Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000
Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000
Partition: MODEM, [000001000000 - 000001800000], size: 000000800000
Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000
Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000
Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000
Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000
Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000
Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000
Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000
Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000
Partition: efs, [000002B00000 - 000003F00000], size: 000001400000
Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000
Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000
Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000
Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000
Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000
Partition: system, [000012D00000 - 000053D00000], size: 000041000000
Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000
Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000
GPT header successfully parsed

Get firmware version

layder · 10-04-2018, 17:44

Quote:

Originally Posted by anjuman

another device done now its j100ml

Operation: Changing GP sizes (test mode) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0

Successfully

Operation: Changing GP sizes (final write) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP1 size: 0 MB , WR_REL: 1 , ENH 0

Successfully

this actions are absolutely unnecessary and meaningless

anjuman · 10-05-2018, 05:55

i did it because i found some video.and there is doing same as i did...its my second device i did it...i know i am not perfect..i am correct now because my device on.now.... so its not matter that is unnecessary and meaningless ...as i want its done..

layder · 10-05-2018, 08:24

Quote:

Originally Posted by anjuman

i did it because i found some video.and there is doing same as i did...its my second device i did it...i know i am not perfect..i am correct now because my device on.now.... so its not matter that is unnecessary and meaningless ...as i want its done..

In this device, there is no GP1 partition, which exists in devices on Intel processors, so your actions only close the flash IC register to make it impossible to create this section in the future and do not change anything else.

I wrote about this so that people would not copy meaningless actions when restoring their devices

anjuman · 10-05-2018, 11:07

ok boss..as i said i am not perfect as you are.......thanks for support.

4star · 11-11-2018, 16:58

Samsung j100h boot repair

Shrink your URLs and get paid!

pintu_das · 11-20-2018, 13:03

samsung j100h

Error: eMMC has a small size

The size of the last section was not updated

when i add pit file

than show error

how to solve it ....

layder · 11-20-2018, 13:12

Quote:

Originally Posted by pintu_das

samsung j100h

Error: eMMC has a small size

The size of the last section was not updated

when i add pit file

than show error

how to solve it ....

You need change Flash IC to solve problem
You eMMC is dead

Rotan Sarkar · 11-25-2018, 16:24

SAMSUNG J1 J100H DEAD BOOT REPAIR DONE

SCREEBSHOT

eMMC_tool Suite ver. 1.5.2.0 (release date: 06.08.2018)
Microsoft Windows 10 (64 bit) build 17134 (10.0.17134.376)

Looking for EasyJTAG box...
EasyJTAG API ver. 2100
EasyJTAG Box Serial = 12FFB00CE943D81E
Card Serial = AA26xxxx
EasyJTAG Box Firmware = 1.63

Setting frequence to 14 Mhz
CMD Pullup Level: 1794 mV
CMD Active Level: 2701 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101CECB09BC422E
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: CECB09BC , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 4/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01
Backup saved: H4G2b_CECB09BC_20181125_205221.extcsd
EMMC Init completed.

Scanning soft partitions
GPT header is found and is valid
Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000 (2.00 MB)
Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000 (2.00 MB)
Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 (1.00 MB)
Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 (1.00 MB)
Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 (1.00 MB)
Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 (1.00 MB)
Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000 (4.00 MB)
Partition: MODEM, [000001000000 - 000001800000], size: 000000800000 (8.00 MB)
Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000 (8.00 MB)
Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000 (4.00 MB)
Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000 (1.00 MB)
Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 (1.00 MB)
Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 (1.00 MB)
Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 (1.00 MB)
Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 (1.00 MB)
Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000 (2.00 MB)
Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 (20.0 MB)
Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 (5.00 MB)
Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000 (1.00 MB)
Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000 (16.0 MB)
Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000 (16.0 MB)
Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000 (200. MB)
Partition: system, [000012D00000 - 000053D00000], size: 000041000000 (1.02 GB)
Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000 (40.0 MB)
Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000 (2.28 GB)
GPT header successfully parsed

Get firmware version

Brand = samsung
Manufacturer = samsung
Model = SM-J100H
Phone platform = sc8830
CPU Abi = armeabi-v7a
Android release = 4.4.4
Firmware version = KTU84P.J100HXXU0AOB4
Firmware date = Wed Feb 11 11:15:08 KST 2015

mobileguard · 11-29-2018, 16:13

HiPower mode is OFF
CMD Pullup Level: 2000 mV
CMD Active Level: 2505 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110182F44CF112EA
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX
EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01
EMMC NAME (HEX): 483447326211
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
Backup saved: H4G2b_82F44CF1_20181129_210411.extcsd
EMMC Init completed.

Operation: Write Dump

Writing to: ROM1 , start: 0x000000000000 , size: 0x000010000000
Input file: H:\flash files\j srises model file\j100h\100h-dump\J100H\EMMC_ROM1_H4G2b_2165950698_00000000_100 00000.bin
eMMC switching to ROM1
Writing partition...
Done writing partition. Write speed: 1430.25 Kb/s

HiPower mode is OFF
CMD Pullup Level: 2010 mV
CMD Active Level: 2516 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110182F44CF112EA
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX
EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01
EMMC NAME (HEX): 483447326211
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
Backup saved: H4G2b_82F44CF1_20181129_210728.extcsd
EMMC Init completed.

Operation: Write Dump

Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000
Input file: H:\flash files\j srises model file\j100h\100h-dump\J100H\EMMC_ROM2_H4G2b_2165950698_00000000_004 00000.bin
eMMC switching to ROM2
Writing partition...
Done writing partition. Write speed: 638.07 Kb/s

HiPower mode is OFF
CMD Pullup Level: 2010 mV
CMD Active Level: 2516 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110182F44CF112EA
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX
EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01
EMMC NAME (HEX): 483447326211
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
Backup saved: H4G2b_82F44CF1_20181129_210744.extcsd
EMMC Init completed.

Operation: Write Dump

Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000
Input file: H:\flash files\j srises model file\j100h\100h-dump\J100H\EMMC_ROM3_H4G2b_2165950698_00000000_004 00000.bin
eMMC switching to ROM3
Writing partition...
Done writing partition. Write speed: 640.36 Kb/s

HiPower mode is OFF
CMD Pullup Level: 2000 mV
CMD Active Level: 2526 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110182F44CF112EA
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX
EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01
EMMC NAME (HEX): 483447326211
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
Backup saved: H4G2b_82F44CF1_20181129_210836.extcsd
EMMC Init completed.

Filename: H4G2b_82F44CF1_20181129_202004.extcsd

Repairing ExtCsd ...
Successfully

plz help

rujeshale · 12-01-2018, 16:28

plz share dead boot repair j100h file j tag

Sent from my SM-J701F using Tapatalk

11-20-2018, 13:03	#116 (permalink)
pintu_das No Life Poster Join Date: Jan 2015 Location: Narsingdi, Dhaka, Bangladesh Age: 28 Posts: 2,207 Member: 2325851 Status: Offline Sonork: 100.1680491 Thanks Meter: 2,363	samsung j100h Error: eMMC has a small size problem samsung j100h Error: eMMC has a small size The size of the last section was not updated when i add pit file than show error how to solve it ....

11-25-2018, 16:24	#118 (permalink)
Rotan Sarkar No Life Poster Join Date: Mar 2010 Location: unlockprice.com Posts: 577 Member: 1263622 Status: Offline Thanks Meter: 149	Samsung j1 j100h dead boot repair with easy jtag SAMSUNG J1 J100H DEAD BOOT REPAIR DONE SCREEBSHOT eMMC_tool Suite ver. 1.5.2.0 (release date: 06.08.2018) Microsoft Windows 10 (64 bit) build 17134 (10.0.17134.376) Looking for EasyJTAG box... EasyJTAG API ver. 2100 EasyJTAG Box Serial = 12FFB00CE943D81E Card Serial = AA26xxxx EasyJTAG Box Firmware = 1.63 Setting frequence to 14 Mhz CMD Pullup Level: 1794 mV CMD Active Level: 2701 mV EMMC Device Information : EMMC CID: 90014A48344732621101CECB09BC422E EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: CECB09BC , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 4/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_CECB09BC_20181125_205221.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000 (2.00 MB) Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000 (2.00 MB) Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 (1.00 MB) Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 (1.00 MB) Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 (1.00 MB) Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 (1.00 MB) Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000 (4.00 MB) Partition: MODEM, [000001000000 - 000001800000], size: 000000800000 (8.00 MB) Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000 (8.00 MB) Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000 (4.00 MB) Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000 (1.00 MB) Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 (1.00 MB) Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 (1.00 MB) Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 (1.00 MB) Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 (1.00 MB) Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000 (2.00 MB) Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 (20.0 MB) Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 (5.00 MB) Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000 (1.00 MB) Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000 (16.0 MB) Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000 (16.0 MB) Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000 (200. MB) Partition: system, [000012D00000 - 000053D00000], size: 000041000000 (1.02 GB) Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000 (40.0 MB) Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000 (2.28 GB) GPT header successfully parsed Get firmware version Brand = samsung Manufacturer = samsung Model = SM-J100H Phone platform = sc8830 CPU Abi = armeabi-v7a Android release = 4.4.4 Firmware version = KTU84P.J100HXXU0AOB4 Firmware date = Wed Feb 11 11:15:08 KST 2015 Last edited by layder; 11-25-2018 at 16:33. Reason: Hide card serial

11-29-2018, 16:13	#119 (permalink)
mobileguard Freak Poster Join Date: Oct 2007 Location: srimongal/moulovibazer/sylhet Posts: 376 Member: 616521 Status: Offline Thanks Meter: 24	j100h Successfully not power on HiPower mode is OFF CMD Pullup Level: 2000 mV CMD Active Level: 2505 mV EMMC Device Information : EMMC CID: 90014A4834473262110182F44CF112EA EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacture Name: SKHYNIX EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01 EMMC NAME (HEX): 483447326211 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Backup saved: H4G2b_82F44CF1_20181129_210411.extcsd EMMC Init completed. Operation: Write Dump Writing to: ROM1 , start: 0x000000000000 , size: 0x000010000000 Input file: H:\flash files\j srises model file\j100h\100h-dump\J100H\EMMC_ROM1_H4G2b_2165950698_00000000_100 00000.bin eMMC switching to ROM1 Writing partition... Done writing partition. Write speed: 1430.25 Kb/s HiPower mode is OFF CMD Pullup Level: 2010 mV CMD Active Level: 2516 mV EMMC Device Information : EMMC CID: 90014A4834473262110182F44CF112EA EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacture Name: SKHYNIX EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01 EMMC NAME (HEX): 483447326211 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Backup saved: H4G2b_82F44CF1_20181129_210728.extcsd EMMC Init completed. Operation: Write Dump Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000 Input file: H:\flash files\j srises model file\j100h\100h-dump\J100H\EMMC_ROM2_H4G2b_2165950698_00000000_004 00000.bin eMMC switching to ROM2 Writing partition... Done writing partition. Write speed: 638.07 Kb/s HiPower mode is OFF CMD Pullup Level: 2010 mV CMD Active Level: 2516 mV EMMC Device Information : EMMC CID: 90014A4834473262110182F44CF112EA EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacture Name: SKHYNIX EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01 EMMC NAME (HEX): 483447326211 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Backup saved: H4G2b_82F44CF1_20181129_210744.extcsd EMMC Init completed. Operation: Write Dump Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000 Input file: H:\flash files\j srises model file\j100h\100h-dump\J100H\EMMC_ROM3_H4G2b_2165950698_00000000_004 00000.bin eMMC switching to ROM3 Writing partition... Done writing partition. Write speed: 640.36 Kb/s HiPower mode is OFF CMD Pullup Level: 2000 mV CMD Active Level: 2526 mV EMMC Device Information : EMMC CID: 90014A4834473262110182F44CF112EA EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacture Name: SKHYNIX EMMC NAME: H4G2b , S/N: 82F44CF1 , rev. 01 EMMC NAME (HEX): 483447326211 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Backup saved: H4G2b_82F44CF1_20181129_210836.extcsd EMMC Init completed. Filename: H4G2b_82F44CF1_20181129_202004.extcsd Repairing ExtCsd ... Successfully plz help

12-01-2018, 16:28	#120 (permalink)
rujeshale Junior Member Join Date: Feb 2014 Posts: 10 Member: 2126552 Status: Offline Thanks Meter: 0	plz share dead boot repair j100h file j tag plz share dead boot repair j100h file j tag Sent from my SM-J701F using Tapatalk

10-02-2018, 13:18	#106 (permalink)
gsmmithun Product Supporter Join Date: Feb 2015 Location: USA.INDIA,BD Age: 32 Posts: 676 Member: 2348745 Status: Offline Sonork: 100.1611282 Thanks Meter: 396	BRO I CHEEK ALL FREQUENCY BUT NOT DONE AFTER change software

10-03-2018, 13:48	#107 (permalink)
anjuman Freak Poster Join Date: Jan 2008 Location: phone care Posts: 468 Member: 667941 Status: Offline Sonork: 100.1611812 Thanks Meter: 61	all done but device still dead any solution. Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 2097 mV CMD Active Level: 2602 mV EMMC Device Information : EMMC CID: 90014A483447326211010DD8404432DD EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_0DD84044_20181003_180700.extcsd EMMC Init completed. Operation: Write all eMMC Regions at once Writing BootConfig ... Reg: 179 Value: 0x08 Reg: 177 Value: 0x00 Reg: 162 Value: 0x00 Done Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000 Filename: EMMC_ROM2_00000000_00400000.bin eMMC switching to ROM2 Writing partition... Done writing partition. Write speed: 701.77 KB/s Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000 Filename: EMMC_ROM3_00000000_00400000.bin eMMC switching to ROM3 Writing partition... Done writing partition. Write speed: 703.94 KB/s Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000 Filename: EMMC_ROM1_00000000_20000000.bin eMMC switching to ROM1 Writing partition... Done writing partition. Write speed: 1793.76 KB/s All done time: [00:05:06:287] Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 2097 mV CMD Active Level: 2603 mV EMMC Device Information : EMMC CID: 90014A483447326211010DD8404432DD EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_0DD84044_20181003_181233.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000 Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000 Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000 Partition: MODEM, [000001000000 - 000001800000], size: 000000800000 Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000 Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000 Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000 Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000 Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000 Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000 Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000 Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000 Partition: system, [000012D00000 - 000053D00000], size: 000041000000 Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000 Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000 GPT header successfully parsed Get firmware version Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 2097 mV CMD Active Level: 2607 mV EMMC Device Information : EMMC CID: 90014A483447326211010DD8404432DD EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_0DD84044_20181003_181617.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000 Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000 Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000 Partition: MODEM, [000001000000 - 000001800000], size: 000000800000 Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000 Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000 Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000 Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000 Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000 Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000 Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000 Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000 Partition: system, [000012D00000 - 000053D00000], size: 000041000000 Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000 Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000 GPT header successfully parsed Get firmware version Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 2094 mV CMD Active Level: 2607 mV EMMC Device Information : EMMC CID: 90014A483447326211010DD8404432DD EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_0DD84044_20181003_181625.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000 Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000 Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000 Partition: MODEM, [000001000000 - 000001800000], size: 000000800000 Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000 Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000 Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000 Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000 Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000 Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000 Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000 Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000 Partition: system, [000012D00000 - 000053D00000], size: 000041000000 Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000 Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000 GPT header successfully parsed Get firmware version

10-03-2018, 14:30	#108 (permalink)
anjuman Freak Poster Join Date: Jan 2008 Location: phone care Posts: 468 Member: 667941 Status: Offline Sonork: 100.1611812 Thanks Meter: 61	again done but still dead Operation: Write by vendor (Samsung) Creating GPT-partitioninig Writing PIT at address: 000000004400 GPT-partitioning done Unpacking file: spl.img Unpacking file: sboot.bin Unpacking file: sboot2.bin Unpacking file: sprddsp.img Unpacking file: sprdcp.img Unpacking file: param.lfs Unpacking file: boot.img Unpacking file: recovery.img Unpacking file: cache.img Unpacking file: system.img Unpacking file: hidden.img Partition name: BOOT Filename: spl.img , Offset: 000000000000 , filesize: 32768 bytes eMMC switching to ROM2 Erasing partition... Writing partition... Done writing partition. Write speed: 485.80 KB/s Partition name: SBOOT Filename: sboot.bin , Offset: 000000400000 , filesize: 1573888 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1753.72 KB/s Partition name: SBOOT2 Filename: sboot2.bin , Offset: 000000600000 , filesize: 1573888 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1745.65 KB/s Partition name: WDSP Filename: sprddsp.img , Offset: 000000C00000 , filesize: 1967104 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1740.28 KB/s Partition name: MODEM Filename: sprdcp.img , Offset: 000001000000 , filesize: 7391600 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1777.16 KB/s Partition name: PARAM Filename: param.lfs , Offset: 000002900000 , filesize: 634880 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1586.28 KB/s Partition name: KERNEL Filename: boot.img , Offset: 000004500000 , filesize: 5696512 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1775.04 KB/s Partition name: RECOVERY Filename: recovery.img , Offset: 000005500000 , filesize: 7033856 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Done writing partition. Write speed: 1779.29 KB/s Partition name: CSC Filename: cache.img , Offset: 000006500000 , filesize: 9834768 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Sparse image found v.1.0 Total chunks: 15 Done writing partition. Write speed: 1748.26 KB/s Partition name: SYSTEM Filename: system.img , Offset: 000012D00000 , filesize: 978769712 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Sparse image found v.1.0 Total chunks: 1649 Done writing partition. Write speed: 1740.57 KB/s Partition name: HIDDEN Filename: hidden.img , Offset: 000053D00000 , filesize: 14807536 bytes eMMC switching to ROM1 Erasing partition... Writing partition... Sparse image found v.1.0 Total chunks: 29 Done writing partition. Write speed: 1728.23 KB/s All done time: [00:11:03:128] Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 2078 mV CMD Active Level: 2603 mV EMMC Device Information : EMMC CID: 90014A483447326211010DD8404432DD EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: 0DD84044 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 3/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_0DD84044_20181003_185655.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: sboot, [000000400000 - 000000600000], size: 000000200000 Partition: sboot2, [000000600000 - 000000800000], size: 000000200000 Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 Partition: wdsp, [000000C00000 - 000001000000], size: 000000400000 Partition: modem, [000001000000 - 000001800000], size: 000000800000 Partition: modem2, [000001800000 - 000002000000], size: 000000800000 Partition: tddsp, [000002000000 - 000002400000], size: 000000400000 Partition: fota_sig, [000002400000 - 000002500000], size: 000000100000 Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 Partition: param, [000002900000 - 000002B00000], size: 000000200000 Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 Partition: reserved2, [000004400000 - 000004500000], size: 000000100000 Partition: kernel, [000004500000 - 000005500000], size: 000001000000 Partition: recovery, [000005500000 - 000006500000], size: 000001000000 Partition: csc, [000006500000 - 000012D00000], size: 00000C800000 Partition: system, [000012D00000 - 000053D00000], size: 000041000000 Partition: hidden, [000053D00000 - 000056500000], size: 000002800000 Partition: userdata, [000056500000 - 0000E8FFBE00], size: 000092AFBE00 GPT header successfully parsed Get firmware version Brand = samsung Manufacturer = samsung Model = SM-J100H Phone platform = sc8830 CPU Abi = armeabi-v7a Android release = 4.4.4 Firmware version = KTU84P.J100HDDU0API1 Firmware date = Mon Sep 5 18:00:10 KST 2016

10-04-2018, 13:00	#109 (permalink)
anjuman Freak Poster Join Date: Jan 2008 Location: phone care Posts: 468 Member: 667941 Status: Offline Sonork: 100.1611812 Thanks Meter: 61	its done friends..i just put it with battery and jig insert..after ten minutes when i check device there is download mode...i restart its hang on logo ..now device ok working fine ...after format in recovery mode..thanks friends and easy jtag team.

10-04-2018, 17:24	#110 (permalink)
anjuman Freak Poster Join Date: Jan 2008 Location: phone care Posts: 468 Member: 667941 Status: Offline Sonork: 100.1611812 Thanks Meter: 61	another device done now its j100ml eMMC_tool Suite ver. 1.4.9.0 (release date: 12.12.2017) Microsoft Windows 7 (32 bit) build 7601 (6.1.7601.18015) Looking for EasyJTAG box... EasyJTAG API ver. 2022 EasyJTAG Box Serial = C339612C47832EE2 Card Serial = AADF-A9ED EasyJTAG Box Firmware = 2.30 Changelog: 12.12.2017 (ver 1.4.9.0) Fix: Bugs that have been found through your crash report Fix: RandomVerify function Fix: Creation of GPT for Samsung (write by vendor) Fix: Failed to mount large Fat partitions (explorer) Fix: Extraction from contact2.db (explorer) Fix: Error in the "build.prop" parser Fix: CID Parser Add: Support for EasyJtag Plus Box Add: Path for TempDir and InitialDir (option in settings) Add: Unpack Lenovo QSB (utilities) Add: Selecting a PIT file from CSC (write by vendor Samsung) Add: Detect for encrypted dumps from GPG Box Add: Detect for FullDiskEncryption Partition (explorer) Add: LinearVerify of the Partition (read by vendor) Add: Information base about emmc compatibility (thanks to phonemicrodb) Add: Resizing the window (for small screen resolutions) Add: Converting large partitions in SparseImage when reading by vendor (option in settings) Add: Mounting SparseImage (explorer) Add: Automatic backup of the EFS partition for Samsung (read by vendor) Add: Formatting of EFS partition for Samsung on request (write by vendor) Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1765 mV CMD Active Level: 1860 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_C73061F1_20181004_213435.extcsd EMMC Init completed. Scanning soft partitions Partition table not found Get firmware version Firmware info not found Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1765 mV CMD Active Level: 1859 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_C73061F1_20181004_213533.extcsd EMMC Init completed. Operation: Universal Factory Format Please, wait ... Successfully Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1765 mV CMD Active Level: 1859 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_C73061F1_20181004_213554.extcsd EMMC Init completed. Operation: Changing GP sizes (test mode) ... GP1 size: 0 MB , WR_REL: 1 , ENH 0 GP1 size: 0 MB , WR_REL: 1 , ENH 0 GP1 size: 0 MB , WR_REL: 1 , ENH 0 GP1 size: 0 MB , WR_REL: 1 , ENH 0 Successfully Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] to cancel the changes Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1763 mV CMD Active Level: 1859 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_C73061F1_20181004_213601.extcsd EMMC Init completed. Operation: Changing GP sizes (final write) ... GP1 size: 0 MB , WR_REL: 1 , ENH 0 GP1 size: 0 MB , WR_REL: 1 , ENH 0 GP1 size: 0 MB , WR_REL: 1 , ENH 0 GP1 size: 0 MB , WR_REL: 1 , ENH 0 Successfully Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0] to finalize operation After reconnect, make sure that the size of ROM1 has been changed. Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1765 mV CMD Active Level: 1860 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_C73061F1_20181004_213622.extcsd EMMC Init completed. Scanning soft partitions Partition table not found Get firmware version Firmware info not found Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1765 mV CMD Active Level: 1859 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_C73061F1_20181004_213729.extcsd EMMC Init completed. Operation: Write all eMMC Regions at once Writing BootConfig ... Reg: 179 Value: 0x08 Reg: 177 Value: 0x00 Reg: 162 Value: 0x00 Done Writing to: ROM2 , start: 0x000000000000 , size: 0x000000400000 Filename: EMMC_ROM2_H4G2b_827544235_00000000_00400000.bin eMMC switching to ROM2 Writing partition... Done writing partition. Write speed: 696.26 KB/s Writing to: ROM3 , start: 0x000000000000 , size: 0x000000400000 Filename: EMMC_ROM3_H4G2b_827544235_00000000_00400000.bin eMMC switching to ROM3 Writing partition... Done writing partition. Write speed: 695.15 KB/s Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000 Filename: EMMC_ROM1_H4G2b_827544235_00000000_20000000.bin eMMC switching to ROM1 Writing partition... Done writing partition. Write speed: 1783.39 KB/s All done time: [00:05:08:183] Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 18 Mhz CMD Pullup Level: 1766 mV CMD Active Level: 1857 mV EMMC Device Information : EMMC CID: 90014A48344732621101C73061F15243 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: C73061F1 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x01 Backup saved: H4G2b_C73061F1_20181004_214334.extcsd EMMC Init completed. Scanning soft partitions GPT header is found and is valid Partition: SBOOT, [000000400000 - 000000600000], size: 000000200000 Partition: SBOOT2, [000000600000 - 000000800000], size: 000000200000 Partition: wfixnv1, [000000800000 - 000000900000], size: 000000100000 Partition: wfixnv2, [000000900000 - 000000A00000], size: 000000100000 Partition: tdfixnv1, [000000A00000 - 000000B00000], size: 000000100000 Partition: tdfixnv2, [000000B00000 - 000000C00000], size: 000000100000 Partition: WDSP, [000000C00000 - 000001000000], size: 000000400000 Partition: MODEM, [000001000000 - 000001800000], size: 000000800000 Partition: MODEM2, [000001800000 - 000002000000], size: 000000800000 Partition: TDDSP, [000002000000 - 000002400000], size: 000000400000 Partition: FOTA_SIG, [000002400000 - 000002500000], size: 000000100000 Partition: wruntimenv1, [000002500000 - 000002600000], size: 000000100000 Partition: wruntimenv2, [000002600000 - 000002700000], size: 000000100000 Partition: tdruntimenv1, [000002700000 - 000002800000], size: 000000100000 Partition: tdruntimenv2, [000002800000 - 000002900000], size: 000000100000 Partition: PARAM, [000002900000 - 000002B00000], size: 000000200000 Partition: efs, [000002B00000 - 000003F00000], size: 000001400000 Partition: prodnv, [000003F00000 - 000004400000], size: 000000500000 Partition: RESERVED2, [000004400000 - 000004500000], size: 000000100000 Partition: KERNEL, [000004500000 - 000005500000], size: 000001000000 Partition: RECOVERY, [000005500000 - 000006500000], size: 000001000000 Partition: CSC, [000006500000 - 000012D00000], size: 00000C800000 Partition: system, [000012D00000 - 000053D00000], size: 000041000000 Partition: HIDDEN, [000053D00000 - 000056500000], size: 000002800000 Partition: userdata, [000056500000 - 0000E8100000], size: 000091C00000 GPT header successfully parsed Get firmware version

10-05-2018, 05:55	#112 (permalink)
anjuman Freak Poster Join Date: Jan 2008 Location: phone care Posts: 468 Member: 667941 Status: Offline Sonork: 100.1611812 Thanks Meter: 61	i did it because i found some video.and there is doing same as i did...its my second device i did it...i know i am not perfect..i am correct now because my device on.now.... so its not matter that is unnecessary and meaningless ...as i want its done..

10-05-2018, 11:07	#114 (permalink)
anjuman Freak Poster Join Date: Jan 2008 Location: phone care Posts: 468 Member: 667941 Status: Offline Sonork: 100.1611812 Thanks Meter: 61	ok boss..as i said i am not perfect as you are.......thanks for support.

11-11-2018, 16:58	#115 (permalink)
4star Freak Poster Join Date: Jun 2011 Location: kolkata Age: 39 Posts: 254 Member: 1596162 Status: Offline Sonork: 100.1616391 Thanks Meter: 146	Samsung j100h boot repair Shrink your URLs and get paid!