GSM Shop GSM Shop
GSM-Forum  

Welcome to the GSM-Forum forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
Only registered members may post questions, contact other members or search our database of over 8 million posts.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

If you have any problems with the registration process or your account login, please contact contact us .

Go Back   GSM-Forum > Product Support Sections > Hard/Software Products (official support) > Easy-Jtag / Easy-Jtag Plus

Easy-Jtag / Easy-Jtag Plus The official support section. You can ask here your question and get answer regarding using Easy-Jtag / Easy-Jtag Plus.

Reply
 
LinkBack Thread Tools Display Modes
Old 02-28-2016, 16:33   #61 (permalink)
No Life Poster
 
>>PakFones<<'s Avatar
 
Join Date: Jul 2007
Location: My Computer
Posts: 1,308
Member: 553178
Status: Offline
Sonork: 100.1592454
Thanks Meter: 957
Donate money to this user

this will work only if you have emmc connection experience before then you will need a tp neadle this needle must be connected with ground wire at detection time. first do experimenta on open emmc when you get hold on it then try on board emmc.

Good Luck dear.

Sent from my SM-N910C using Tapatalk
  Reply With Quote
Old 02-29-2016, 11:51   #62 (permalink)
No Life Poster
 
c_ahmad79's Avatar
 
Join Date: Jan 2006
Location: inside emmc ufs
Age: 19
Posts: 7,188
Member: 221603
Status: Offline
Sonork: 100.1581270
Thanks Meter: 6,395
Donate money to this user
Quote:
Originally Posted by shamsulhaq View Post
all fak becase how to thoch neduls to tp no gape bord or mmce ic
Quote:
Originally Posted by shabirahmad22 View Post
pake post i9300 not warking example no prove
@ >>PakFones<< Good work mate
@shamsulhaq @ shabirahmad22 this is not fake this is real
we are doing this since months without removing emmc ic on i9300/n7100
if you need prove bring sets with such issue we will show you how to do this in few mins without removing emmc or any components

Regards
  Reply With Quote
The Following User Says Thank You to c_ahmad79 For This Useful Post:
Old 02-29-2016, 12:46   #63 (permalink)
No Life Poster
 
>>PakFones<<'s Avatar
 
Join Date: Jul 2007
Location: My Computer
Posts: 1,308
Member: 553178
Status: Offline
Sonork: 100.1592454
Thanks Meter: 957
Donate money to this user
@shamsulhaq and shabirahmad22 :

don't worry dear everything is no impossible in this world. one more update i have dumped emmc with usb flash drive pcb also connect memory card on it few years ago. i have got this picture from my facebook account you can see there.

uploadfromtaptalk1456746335742.jpg

Sent from my SM-N910C using Tapatalk
  Reply With Quote
Old 04-04-2016, 07:03   #64 (permalink)
Junior Member
 
Join Date: Feb 2010
Location: India
Posts: 12
Member: 1243803
Status: Offline
Thanks Meter: 1
Nice work here
Thanks very much
  Reply With Quote
Old 06-12-2016, 10:34   #65 (permalink)
Freak Poster
 
Join Date: Aug 2007
Posts: 140
Member: 575256
Status: Offline
Thanks Meter: 34
Quote:
Originally Posted by rajeshchiyyan View Post
Here IS the MAGIC TP
Howw do to TP this emmc whitout remove the Emmc,,,pleasee share it broooo????,,,,
  Reply With Quote
The Following User Says Thank You to sbycell For This Useful Post:
Old 06-19-2016, 04:00   #66 (permalink)
Crazy Poster
 
Join Date: Jul 2009
Posts: 53
Member: 1065227
Status: Offline
Thanks Meter: 10
Anyone work out how to not wipe the eMMC with firmware update.? If so please telll...??
  Reply With Quote
The Following User Says Thank You to don_paolo For This Useful Post:
Old 08-03-2016, 20:35   #67 (permalink)
Junior Member
 
Join Date: Apr 2015
Location: indonesia
Age: 44
Posts: 16
Member: 2372463
Status: Offline
Sonork: koclok
Thanks Meter: 7
please help me
pinout samsung SM-G316HU/DS
  Reply With Quote
The Following User Says Thank You to koclok2 For This Useful Post:
Old 08-11-2016, 17:37   #68 (permalink)
Freak Poster
 
Join Date: May 2016
Location: Saudi Arab Dammam
Posts: 102
Member: 2574123
Status: Offline
Sonork: 100.1652460
Thanks Meter: 11
before repair it was dead

JTAG Connection is not supported for this device
Z3X EasyJtag Software ver. 2.2.0.2
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 1616100C7FD4B36E, ,FW Ver.: 01.55CMD Pullup Level:2010 mV
CMD Active Level:2475 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: 000000_ 537986854_20160811_1922.extcsd
Done.⁠⁠⁠⁠



after repair

Z3X EasyJtag Software ver. 2.2.0.2
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 1616100C7FD4B36E, ,FW Ver.: 01.55CMD Pullup Level:2547 mV
CMD Active Level:3124 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------
EMMC CID : 1501005654553030300C20138686416E
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xC
EMMC NAME: VTU000 , S/N: 538150534
EMMC NAME (HEX): 56545530303000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: VTU000_ 538150534_20160811_1931.extcsd
Done.



world best z3x team
  Reply With Quote
The Following User Says Thank You to khanyunus For This Useful Post:
Old 08-12-2016, 13:15   #69 (permalink)
Junior Member
 
Join Date: Apr 2014
Posts: 20
Member: 2176617
Status: Offline
Thanks Meter: 2
nice information and zex jtag price?????
  Reply With Quote
The Following User Says Thank You to sunnyhoney323 For This Useful Post:
Old 10-03-2016, 14:05   #70 (permalink)
No Life Poster
 
Gsmbizz's Avatar
 
Join Date: Apr 2008
Age: 28
Posts: 1,696
Member: 745672
Status: Offline
Thanks Meter: 556
i still dont know ....why to use special needle ? pls explain more why we need that
  Reply With Quote
The Following User Says Thank You to Gsmbizz For This Useful Post:
Old 01-18-2017, 13:15   #71 (permalink)
Freak Poster
 
Join Date: Mar 2014
Location: Earth
Posts: 105
Member: 2148096
Status: Offline
Sonork: 100.1674885
Thanks Meter: 27
very good i need some video !!!! Thanks.
  Reply With Quote
The Following User Says Thank You to Ahir paresh For This Useful Post:
Old 01-23-2017, 16:37   #72 (permalink)
Freak Poster
 
Join Date: Apr 2014
Posts: 212
Member: 2177146
Status: Offline
Thanks Meter: 20
Is it just a wire attached to the ic????
  Reply With Quote
The Following User Says Thank You to h.azaraa For This Useful Post:
Old 08-20-2017, 03:16   #73 (permalink)
Insane Poster
 
Join Date: Sep 2015
Posts: 83
Member: 2459405
Status: Offline
Thanks Meter: 17
Quote:
Originally Posted by h.azaraa View Post
Is it just a wire attached to the ic????
yes and you must must know where to connect the TP
  Reply With Quote
The Following User Says Thank You to mgc03 For This Useful Post:
Old 09-08-2017, 18:55   #74 (permalink)
No Life Poster
 
Join Date: Mar 2012
Location: gsm world
Posts: 887
Member: 1741973
Status: Offline
Thanks Meter: 115
where is the tp point?

Quote:
Originally Posted by sbycell View Post
Howw do to TP this emmc whitout remove the Emmc,,,pleasee share it broooo????,,,,
what pin number is the tp kindly put a marking
  Reply With Quote
The Following User Says Thank You to chmsc_ELX For This Useful Post:
Old 10-12-2017, 09:24   #75 (permalink)
Insane Poster
 
Join Date: Oct 2017
Posts: 66
Member: 2767056
Status: Offline
Thanks Meter: 22
With great interest I looked at the topic.
  Reply With Quote
The Following User Says Thank You to M@ster1974 For This Useful Post:
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 



All times are GMT +1. The time now is 00:09.



Powered by Searchlight © 2024 Axivo Inc.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -
Page generated in 0.27030 seconds with 9 queries

SEO by vBSEO