Step by step manual how to repair KMVYL000LM-B503 in pictures. - Page 3 - GSM-Forum

KrzychuG · 04-28-2016, 15:17

Quote:

Originally Posted by Be1thaz0r

I have two 9100s with same problem and same EMMC, does this procedure kill client data?

Similar question here. I have i9100, not booting, easy-jtag says "OCR Ready Timeout Error [Check VCC or eMMC DEAD]" so i assume eMMC might be bad. Since eMMC should be able to identify by using testpoint, is it possible (at this point) to just dump existing content before doing a firmware update to extract data?

rasheedc007 · 04-30-2016, 08:56

FIRMWARE UPDATE SECSESS.BUT CANT POWER ON AFTER WRITE ROM 1.ROM2.USERAREA AND EXTCSD.. WERE IS FAULT??

image free hosting

Phihunggsm · 11-28-2016, 12:54

Working done! Thanks bro

RNBeez · 05-01-2017, 15:58

Hi, anyone can show me where to find the Picture of TP in easy-jtag, my emmc type is KLM8G1GEAC-B001.

Thx for all

toninhosantos · 05-02-2017, 04:56

i9192 dead, can repair without remove emmc chip?

RNBeez · 05-04-2017, 13:45

Hi all, anyone ever success with KLM8G1GEAC-B001 repair?
Here is the log :

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: XxX, ,FW Ver.: 01.58
CMD Pullup Level:2062 mV
CMD Active Level:3114 mV
Box IO Level:3300 mV
CLK Rate:7000 khz
HiPower mode is off!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

thanks for respond

kit_kit · 01-07-2019, 09:47

is this works for those emmc we take out in n7100 Dead with 130mah stucked when turn on ?

04-30-2016, 08:56	#32 (permalink)
rasheedc007 No Life Poster Join Date: Feb 2010 Location: india. kerala. Posts: 1,539 Member: 1245320 Status: Offline Sonork: 100.1612126 Thanks Meter: 140	FIRMWARE UPDATE SECSESS.BUT CANT POWER ON AFTER WRITE ROM 1.ROM2.USERAREA AND EXTCSD.. WERE IS FAULT?? image free hosting

11-28-2016, 12:54	#33 (permalink)
Phihunggsm Junior Member Join Date: Apr 2016 Posts: 1 Member: 2566196 Status: Offline Thanks Meter: 0	Working done! Thanks bro

05-01-2017, 15:58	#34 (permalink)
RNBeez Junior Member Join Date: Jan 2017 Location: Indonesia Posts: 7 Member: 2673693 Status: Offline Thanks Meter: 1	Hi, anyone can show me where to find the Picture of TP in easy-jtag, my emmc type is KLM8G1GEAC-B001. Thx for all

05-02-2017, 04:56	#35 (permalink)
toninhosantos No Life Poster Join Date: Jun 2010 Location: Xique-Xique-Bahia, Brasil Age: 46 Posts: 904 Member: 1320000 Status: Offline Sonork: 100.1667898 Thanks Meter: 272	i9192 dead, can repair without remove emmc chip?

05-04-2017, 13:45	#36 (permalink)
RNBeez Junior Member Join Date: Jan 2017 Location: Indonesia Posts: 7 Member: 2673693 Status: Offline Thanks Meter: 1	Hi all, anyone ever success with KLM8G1GEAC-B001 repair? Here is the log : Loading eMMC Addon Firmware... IO: 3300 mV Box S/N: XxX, ,FW Ver.: 01.58 CMD Pullup Level:2062 mV CMD Active Level:3114 mV Box IO Level:3300 mV CLK Rate:7000 khz HiPower mode is off! Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD] Done. thanks for respond

01-07-2019, 09:47	#37 (permalink)
kit_kit Freak Poster Join Date: Feb 2004 Location: Malaysia Age: 38 Posts: 261 Member: 55800 Status: Offline Thanks Meter: 9	is this works for those emmc we take out in n7100 Dead with 130mah stucked when turn on ?