Successfully repaired VTU00M name 00000000, for GT-i9300 - Page 3 - GSM-Forum

drjaved_akhter · 06-06-2014, 18:55

Quote:

Originally Posted by maplegsm

CMD Active Level:1742 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Access to current partition forbidden ( size=0 )
Done !!!

Z3X EasyJtag Software ver. 1.5.1.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 16160C0B8F6638CB, ,FW Ver.: 01.50
CMD Pullup Level:1299 mV
CMD Active Level:1742 mV
eMMC Device Information
EMMC CID : 15010056545530304DF124152A395FDA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 605366841
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 0 kB
EMMC ROM3 (Boot Partition 2) Capacity: 0 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VTU00M_ 605366841_20140505_2227.extcsd
Done.
Writing file...H:\Z3x\jtag\i9300\dump\EMMC_ROM1_00000000_2 0000000.bin

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1299 mV
CMD Active Level:1742 mV
Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM)
Write Speed: 687 kB/s
Done !!!

after repair emmc name 0000.. ROM2 and ROM3 adress not good
EMMC ROM2 (Boot Partition 1) Capacity: 0 kB
EMMC ROM3 (Boot Partition 2) Capacity: 0 kB

how to resize ?

use search button i upload this video for resize partition

maplegsm · 06-06-2014, 19:09

set is dead .............

drjaved_akhter · 06-11-2014, 16:29

i request z3x team please add new update emmc tool logs back up in pc............

thanks

beg-one · 06-19-2014, 01:51

is this a bad emmc ,or its duo to soldering ,wares connection , hardware...

===================================

Z3X EasyJtag Software ver. 1.5.2.3
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 0800A006DD1A858D, ,FW Ver.: 01.50
CMD Pullup Level:1928 mV
CMD Active Level:2279 mV
eMMC Device Information
EMMC CID : 15010030303030303333333307265812
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x33
EMMC NAME: 000003 , S/N: 858982182
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000003_ 858982182_20140504_0040.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 1.5.2.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1928 mV
CMD Active Level:2279 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Erasing repair area...
Success
Writing repair area...
Warning Writing repair area fail
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
===================================

mobilegsm30 · 06-23-2014, 14:36

Code:

Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1381 mV
CMD Active Level:1825 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005  Rev.0x56
EMMC NAME: <b>000000</b> , S/N:  537986854
EMMC ROM1 (Main User Data)   Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20140501_1627.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1825 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 1...
Success
===================================
<font color="red">NOTE: This stage was reapir only eMMC NAME , not wear leveling data!!</font>
<font color="red">NOTE: Repair Stage 2 must be done to make eMMC repair completely!</font>
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1825 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Warning Can't enter repair mode 2, Reason: CARD Ready Timeout Error 
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1825 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Warning Can't enter repair mode 2, Reason: CARD Ready Timeout Error 
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1825 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 2...
<font color="green">Success</font>
<font color="green">EMMC repair Done , Reconect eMMC and check S.M.A.R.T Report.</font>
<font color="green">Please don't forget to repair <b>extCSD</b> from backup!!!</font>
<font color="green">Please don't forget to configure <b>BOOT</b> sizes!!!</font>
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
eMMC Device Information
EMMC CID : 15010056545530304DF13A7E479D5F62

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012  Rev.0xf1
EMMC NAME: <b>VTU00M</b> , S/N:  981354397
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.
Backup saved: VTU00M_ 981354397_20140501_1630.extcsd
Done.
Running:SAMSUNG: Read S.M.A.R.T Report...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode  : Normal

Super Block size              : 0x00800000 (8388608 bytes)
Super Page size               : 0x00004000 (16384 bytes)
Optimal Write size            : 0x00010000 (65536 bytes)
Read Reclaim count            : 0
Optimal TRIM size             : 0x00002000 (8192 bytes)
Total Number of banks         : 4
Initial bad blocks per bank   : 3,2,1,4
Runtime bad blocks per bank   : 0,0,0,0
Reserved blocks left per bank : 48,49,50,47
All Erase counts (min,avg,max): 0,0,1
SLC Erase counts (min,avg,max): 0,0,1
MLC Erase counts (min,avg,max): 0,0,0
S.M.A.R.T Report Done !!!
Running:Repair extCSD...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing...
Done!
Done.
<font color="red">Please don't forget to repair extCSD from backup!!!</font>
Running:Change BOOT CONFIG...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing eMMC Register...
Written: REG : 179 VAL :48 
Done.
Running:Change BOOT WIDTH...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing eMMC Register...
Written: REG : 177 VAL :1 
Done.
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM)
Retry writing adress 0x00014000 (Attempt #1)...
Retry Success !!! Disabling Write Optimistations...
Retry writing adress 0x00025200 (Attempt #1)...
Retry Success !!! Disabling Write Optimistations...
Write Speed: 704 kB/s
Done !!!
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 814 kB/s
Done !!!
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1371 mV
CMD Active Level:1815 mV
eMMC Device Information
EMMC CID : 15010056545530304DF13A7E479D5F62

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012  Rev.0xf1
EMMC NAME: <b>VTU00M</b> , S/N:  981354397
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits  , Partition config [179]: 0x48.
Backup saved: VTU00M_ 981354397_20140501_1646.extcsd
Done.
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1371 mV
CMD Active Level:1835 mV
eMMC Device Information
EMMC CID : 15010056545530304DF13A7E479D5F62

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012  Rev.0xf1
EMMC NAME: <b>VTU00M</b> , S/N:  981354397
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits  , Partition config [179]: 0x48.
Backup saved: VTU00M_ 981354397_20140501_1647.extcsd
Done.
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1361 mV
CMD Active Level:1835 mV
eMMC Device Information
EMMC CID : 15010056545530304DF13A7E479D5F62

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012  Rev.0xf1
EMMC NAME: <b>VTU00M</b> , S/N:  981354397
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits  , Partition config [179]: 0x48.
Backup saved: VTU00M_ 981354397_20140501_1648.extcsd
Done.

mobilegsm30 · 06-23-2014, 14:38

Code:

Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1381 mV
CMD Active Level:1815 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005  Rev.0x56
EMMC NAME: <b>000000</b> , S/N:  537986854
EMMC ROM1 (Main User Data)   Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20140501_1807.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1815 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 1...
Success
===================================
<font color="red">NOTE: This stage was reapir only eMMC NAME , not wear leveling data!!</font>
<font color="red">NOTE: Repair Stage 2 must be done to make eMMC repair completely!</font>
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1815 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Warning Can't enter repair mode 2, Reason: CARD Ready Timeout Error 
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1815 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Warning Can't enter repair mode 2, Reason: CARD Ready Timeout Error 
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1815 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Warning Can't enter repair mode 2, Reason: CARD Ready Timeout Error 
<font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font>
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1815 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 2...
<font color="green">Success</font>
<font color="green">EMMC repair Done , Reconect eMMC and check S.M.A.R.T Report.</font>
<font color="green">Please don't forget to repair <b>extCSD</b> from backup!!!</font>
<font color="green">Please don't forget to configure <b>BOOT</b> sizes!!!</font>
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1414FF0180A9D84A, ,FW Ver.: 01.50
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
eMMC Device Information
EMMC CID : 15010056545530304DF17AC849465FF2

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012  Rev.0xf1
EMMC NAME: <b>VTU00M</b> , S/N: 2059946310
EMMC ROM1 (Main User Data)   Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
  Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.
Backup saved: VTU00M_2059946310_20140501_1809.extcsd
Done.
Running:SAMSUNG: Read S.M.A.R.T Report...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode  : Normal

Super Block size              : 0x00800000 (8388608 bytes)
Super Page size               : 0x00004000 (16384 bytes)
Optimal Write size            : 0x00010000 (65536 bytes)
Read Reclaim count            : 0
Optimal TRIM size             : 0x00002000 (8192 bytes)
Total Number of banks         : 4
Initial bad blocks per bank   : 2,2,3,6
Runtime bad blocks per bank   : 0,0,0,0
Reserved blocks left per bank : 49,49,48,45
All Erase counts (min,avg,max): 0,0,1
SLC Erase counts (min,avg,max): 0,0,1
MLC Erase counts (min,avg,max): 0,0,0
S.M.A.R.T Report Done !!!
Running:Repair extCSD...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing...
Done!
Done.
<font color="red">Please don't forget to repair extCSD from backup!!!</font>
Running:Change BOOT CONFIG...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing eMMC Register...
Written: REG : 179 VAL :48 
Done.
Running:Change BOOT WIDTH...
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing eMMC Register...
Written: REG : 177 VAL :1 
Done.
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM)
Write Speed: 2499 kB/s
Done !!!
<br>
Z3X EasyJtag Software ver. 1.5.5.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1381 mV
CMD Active Level:1835 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 819 kB/s
Done !!!

francoo · 08-11-2014, 17:14

Z3X EasyJtag Software ver. 1.5.2.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 161606050BBA9215, ,FW Ver.: 01.50
CMD Pullup Level:1330 mV
CMD Active Level:1753 mV
eMMC Device Information
EMMC CID : 1501003030303030300C201301281062

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 01/2013 Rev.0xc
EMMC NAME: 000000 , S/N: 538116392
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: 000000_ 538116392_20140403_1338.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
 
Z3X EasyJtag Software ver. 1.5.2.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1330 mV
CMD Active Level:1753 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 1...
Success
===================================
NOTE: This stage was reapir only eMMC NAME , not wear leveling data!!
NOTE: Repair Stage 2 must be done to make eMMC repair completely!
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
===================================
 
Z3X EasyJtag Software ver. 1.5.2.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 161606050BBA9215, ,FW Ver.: 01.50
CMD Pullup Level:1330 mV
CMD Active Level:1732 mV
eMMC Device Information
EMMC CID : 15010056545530304DF16B75594F4FA4

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 1802852687
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_1802852687_20140403_1340.extcsd
Done.

unlock in nepal · 10-06-2014, 18:14

VTU00M Name 0000 Repair ok

Z3X EasyJtag Software ver. 1.6.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1299 mV
CMD Active Level:1732 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 1...
Success
===================================
NOTE: This stage was reapir only eMMC NAME , not wear leveling data!!
NOTE: Repair Stage 2 must be done to make eMMC repair completely!
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
===================================
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
 
Z3X EasyJtag Software ver. 1.6.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1299 mV
CMD Active Level:1732 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 2...
Success
EMMC repair Done , Reconect eMMC and check S.M.A.R.T Report.
Please don't forget to repair extCSD from backup!!!
Please don't forget to configure BOOT sizes!!!
Running:SAMSUNG: Read S.M.A.R.T Report...
 

S.M.A.R.T Report

Super Block size : 0x00800000 (8388608 bytes)
Super Page size : 0x00004000 (16384 bytes)
Optimal Write size : 0x00010000 (65536 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00002000 (8192 bytes)
Total Number of banks : 4
Initial bad blocks per bank : 4,2,3,3
Runtime bad blocks per bank : 0,0,0,0
Reserved blocks left per bank : 47,49,48,48
All Erase counts (min,avg,max): 0,0,1
SLC Erase counts (min,avg,max): 0,0,1
MLC Erase counts (min,avg,max): 0,0,0
S.M.A.R.T Report Done !!!

SAMSUNG: MoviNAND Reset + Format

eMMC Device Information
EMMC CID : 15010056545530304DF1090542D05F28

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 151339728
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VTU00M_ 151339728_20140901_1827.extcsd
Done.
Running:SAMSUNG: MoviNAND Reset + Format...

SAMSUNG: MoviNAND Factory Reset

EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!!!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
Running:SAMSUNG: MoviNAND Factory Reset...
Skip loading eMMC Addon Firmware
CMD Pullup Level:1289 mV
CMD Active Level:1732 mV
Sending Smart Wipe Request...
Wiping Card... Please do not touch it!!!
Done.
Please don't forget to repair extCSD from backup!!!
Running:Repair extCSD...

ROM2

Super Block size : 0x00800000 (8388608 bytes)
Super Page size : 0x00004000 (16384 bytes)

Optimal Write size : 0x00010000 (65536 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00002000 (8192 bytes)
Total Number of banks : 4
Initial bad blocks per bank : 4,2,3,3
Runtime bad blocks per bank : 0,0,0,0
Reserved blocks left per bank : 47,49,48,48
All Erase counts (min,avg,max): 0,1,3
SLC Erase counts (min,avg,max): 0,0,2
MLC Erase counts (min,avg,max): 1,1,3
S.M.A.R.T Report Done !!!
 
Z3X EasyJtag Software ver. 1.6.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1289 mV
CMD Active Level:1711 mV
Input file : D:\JTAG Box\EasyJTAG Tool\S3 error\File\EMMC_ROM2_2Mb_BOOT\EMMC_ROM2_00000000_0 0200000.bin
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 844 kB/s
Done !!!

ROM1

Skip loading eMMC Addon Firmware
CMD Pullup Level:1268 mV
CMD Active Level:1722 mV
Input file : D:\JTAG Box\EasyJTAG Tool\S3 error\File\EMMC_ROM1_512Mb_USER\EMMC_ROM1_00000000 _20000000.bin
Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM)
Write Speed: 2595 kB/s
Done !!!
 

at last info lick this

eMMC Device Information
EMMC CID : 15010056545530304DF1090542D05F28

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 151339728
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_ 151339728_20140901_1900.extcsd
Done.

But no power on

unlock in nepal · 10-06-2014, 18:21

unlock in nepal · 10-07-2014, 15:43

Quote:

Originally Posted by drjaved_akhter

one more gt-i9300 repair

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1237 mV
CMD Active Level:1608 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Success
Erasing repair area...
Success
Writing repair area...
Success
Exit repair mode 2...
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode : Normal
Super Block size : 0x00800000 (8388608 bytes)
Super Page size : 0x00004000 (16384 bytes)
Optimal Write size : 0x00010000 (65536 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00002000 (8192 bytes)
Total Number of banks : 4
Initial bad blocks per bank : 2,2,2,2
Runtime bad blocks per bank : 0,0,0,0
Reserved blocks left per bank : 49,49,49,49
All Erase counts (min,avg,max): 0,0,1
SLC Erase counts (min,avg,max): 0,0,1
MLC Erase counts (min,avg,max): 0,0,0
S.M.A.R.T Report Done !!!
Success
EMMC repair Done
Please don't forget to repair extCSD from backup!!!
Please don't forget to configure BOOT sizes!!!
extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\000000_ 537986854_20140403_1228.extcsd
Running:Repair extCSD...

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1237 mV
CMD Active Level:1608 mV
Writing...
Done!
Done.
Please don't forget to repair extCSD from backup!!!
Running:Change BOOT CONFIG...

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1237 mV
CMD Active Level:1608 mV
Writing eMMC Register...
Written: REG : 179 VAL :8
Done.
Please don't forget to repair extCSD from backup!!!

Z3X EasyJtag Software ver. 1.5.1.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 1717160DCD0D8A9F, ,FW Ver.: 01.50
CMD Pullup Level:1216 mV
CMD Active Level:1598 mV
eMMC Device Information
EMMC CID : 15010056545530304DF1E9AC06326F48
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 06/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 3920365106
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
Backup saved: VTU00M_3920365106_20140403_1236.extcsd
Done.
Writing file...E:\ALL DEVISES\z3x\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM2_00000000_00200000.bin

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1216 mV
CMD Active Level:1598 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 819 kB/s
Done !!!
Writing file...E:\ALL DEVISES\z3x\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1216 mV
CMD Active Level:1598 mV
Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM)
Write Speed: 836 kB/s
Done !!!

Healp sir 2 pone in hand repair ok but no power on

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1216 mV
CMD Active Level:1598 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 819 kB/s
Done !!!
Writing file...E:\ALL DEVISES\z3x\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin

Ploz healp me fore this stapes

were found this file

GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin

drjaved_akhter · 10-08-2014, 08:58

Quote:

Originally Posted by unlock in nepal

Healp sir 2 pone in hand repair ok but no power on

Z3X EasyJtag Software ver. 1.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1216 mV
CMD Active Level:1598 mV
Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Speed: 819 kB/s
Done !!!
Writing file...E:\ALL DEVISES\z3x\9. Easy Jtag files\Samsung\GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin

Ploz healp me fore this stapes

were found this file

GT-I9300\Dump\EMMC_ROM1_00000000_20000000.bin

check clk regestor or direct it with jumper.....

unlock in nepal · 10-09-2014, 19:04

Support file is always no power on i nead tasted rom & working VTU00M_ 792068627_20140103_1914.extcsd file Healp me fore all working file

I have same running phone how to read file from ruanning phone healp me

drjaved_akhter · 05-15-2015, 14:15

Quote:

Originally Posted by unlock in nepal

Support file is always no power on i nead tasted rom & working VTU00M_ 792068627_20140103_1914.extcsd file Healp me fore all working file

I have same running phone how to read file from ruanning phone healp me

select rom 1 size 512 and read.select rom 2 size 2mb and rom 3 2mb read.................

feruzr5 · 06-11-2015, 22:57

how to repair this eror

Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1268 mV
CMD Active Level:3083 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Erasing repair area...
Success!
Writing repair area...
Warning Writing repair area fail
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
Done.

drjaved_akhter · 06-12-2015, 16:15

Quote:

Originally Posted by feruzr5

how to repair this eror

Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1268 mV
CMD Active Level:3083 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Erasing repair area...
Success!
Writing repair area...
Warning Writing repair area fail
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
Done.

always use update exe.emmc tool now v2.02 .use update emmc firmware your problem solved........................

06-19-2014, 01:51	#34 (permalink)
beg-one Freak Poster Join Date: May 2014 Posts: 448 Member: 2194348 Status: Offline Thanks Meter: 52	can't repair , is this a bad emmc ,or its duo to soldering ,wares connection , hardware... =================================== Z3X EasyJtag Software ver. 1.5.2.3 Loading eMMC Addon Firmware... IO: 1850 mV Box S/N: 0800A006DD1A858D, ,FW Ver.: 01.50 CMD Pullup Level:1928 mV CMD Active Level:2279 mV eMMC Device Information EMMC CID : 15010030303030303333333307265812 EMMC CSD : 902701320F5903FFF6DBFFEF8A404022 EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 05/2005 Rev.0x33 EMMC NAME: 000003 , S/N: 858982182 EMMC ROM1 (Main User Data) Capacity: 16384 MB EMMC ROM2 (Boot Partition 1) Capacity: 512 kB EMMC ROM3 (Boot Partition 2) Capacity: 512 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: 000003_ 858982182_20140504_0040.extcsd Done. Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair... Z3X EasyJtag Software ver. 1.5.2.3 Skip loading eMMC Addon Firmware CMD Pullup Level:1928 mV CMD Active Level:2279 mV Repair VTU00M eMMC: Entering repair mode 1... Erasing repair area... Success Writing repair area... Warning Writing repair area fail Please, Reconnect eMMC power lines and press 'VTU00M Repair' again ===================================

08-11-2014, 17:14	#37 (permalink)
francoo Freak Poster Join Date: Jul 2004 Location: Chile Posts: 376 Member: 71290 Status: Offline Sonork: 100.1645657 Thanks Meter: 104	thk Z3X <br> Z3X EasyJtag Software ver. 1.5.2.0 Loading eMMC Addon Firmware... IO: 1850 mV Box S/N: 161606050BBA9215, ,FW Ver.: 01.50 CMD Pullup Level:1330 mV CMD Active Level:1753 mV eMMC Device Information EMMC CID : 1501003030303030300C201301281062 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 01/2013 Rev.0xc EMMC NAME: <b>000000</b> , S/N: 538116392 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: 000000_ 538116392_20140403_1338.extcsd Done. Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair... <br> Z3X EasyJtag Software ver. 1.5.2.0 Skip loading eMMC Addon Firmware CMD Pullup Level:1330 mV CMD Active Level:1753 mV Repair VTU00M eMMC: Entering repair mode 1... Success Erasing repair area... Success Writing repair area... Success Exit repair mode 1... Success =================================== <font color="red">NOTE: This stage was reapir only eMMC NAME , not wear leveling data!!</font> <font color="red">NOTE: Repair Stage 2 must be done to make eMMC repair completely!</font> <font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font> =================================== <br> Z3X EasyJtag Software ver. 1.5.2.0 Loading eMMC Addon Firmware... IO: 1850 mV Box S/N: 161606050BBA9215, ,FW Ver.: 01.50 CMD Pullup Level:1330 mV CMD Active Level:1732 mV eMMC Device Information EMMC CID : 15010056545530304DF16B75594F4FA4 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 04/2012 Rev.0xf1 EMMC NAME: <b>VTU00M</b> , S/N: 1802852687 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_1802852687_20140403_1340.extcsd Done.

10-06-2014, 18:14	#38 (permalink)
unlock in nepal No Life Poster Join Date: Nov 2011 Location: Student Posts: 1,225 Member: 1686564 Status: Offline Sonork: PM me Thanks Meter: 157	EMMC NAME:0000000000 repair ok but no power on VTU00M Name 0000 Repair ok Z3X EasyJtag Software ver. 1.6.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:1299 mV CMD Active Level:1732 mV Repair VTU00M eMMC: Entering repair mode 1... Success Erasing repair area... Success Writing repair area... Success Exit repair mode 1... Success =================================== <font color="red">NOTE: This stage was reapir only eMMC NAME , not wear leveling data!!</font> <font color="red">NOTE: Repair Stage 2 must be done to make eMMC repair completely!</font> <font color="red">Please, Reconnect eMMC power lines and press 'VTU00M Repair' again</font> =================================== Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair... <br> Z3X EasyJtag Software ver. 1.6.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:1299 mV CMD Active Level:1732 mV Repair VTU00M eMMC: Entering repair mode 2... Success Erasing repair area... Success Writing repair area... Success Exit repair mode 2... <font color="green">Success</font> <font color="green">EMMC repair Done , Reconect eMMC and check S.M.A.R.T Report.</font> <font color="green">Please don't forget to repair <b>extCSD</b> from backup!!!</font> <font color="green">Please don't forget to configure <b>BOOT</b> sizes!!!</font> Running:SAMSUNG: Read S.M.A.R.T Report... <br> S.M.A.R.T Report Super Block size : 0x00800000 (8388608 bytes) Super Page size : 0x00004000 (16384 bytes) Optimal Write size : 0x00010000 (65536 bytes) Read Reclaim count : 0 Optimal TRIM size : 0x00002000 (8192 bytes) Total Number of banks : 4 Initial bad blocks per bank : 4,2,3,3 Runtime bad blocks per bank : 0,0,0,0 Reserved blocks left per bank : 47,49,48,48 All Erase counts (min,avg,max): 0,0,1 SLC Erase counts (min,avg,max): 0,0,1 MLC Erase counts (min,avg,max): 0,0,0 S.M.A.R.T Report Done !!! SAMSUNG: MoviNAND Reset + Format eMMC Device Information EMMC CID : 15010056545530304DF1090542D05F28 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 05/2012 Rev.0xf1 EMMC NAME: <b>VTU00M</b> , S/N: 151339728 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: VTU00M_ 151339728_20140901_1827.extcsd Done. Running:SAMSUNG: MoviNAND Reset + Format... SAMSUNG: MoviNAND Factory Reset EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Sending Internal Reconfiguration Request... Waiting configuration Apply!!! Restoring configuration... EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Wiping Card... Please do not touch it!!! Done. <font color="red">Please don't forget to repair extCSD from backup!!!</font> Running:SAMSUNG: MoviNAND Factory Reset... Skip loading eMMC Addon Firmware CMD Pullup Level:1289 mV CMD Active Level:1732 mV Sending Smart Wipe Request... Wiping Card... Please do not touch it!!! Done. <font color="red">Please don't forget to repair extCSD from backup!!!</font> Running:Repair extCSD... ROM2 Super Block size : 0x00800000 (8388608 bytes) Super Page size : 0x00004000 (16384 bytes) Optimal Write size : 0x00010000 (65536 bytes) Read Reclaim count : 0 Optimal TRIM size : 0x00002000 (8192 bytes) Total Number of banks : 4 Initial bad blocks per bank : 4,2,3,3 Runtime bad blocks per bank : 0,0,0,0 Reserved blocks left per bank : 47,49,48,48 All Erase counts (min,avg,max): 0,1,3 SLC Erase counts (min,avg,max): 0,0,2 MLC Erase counts (min,avg,max): 1,1,3 S.M.A.R.T Report Done !!! <br> Z3X EasyJtag Software ver. 1.6.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:1289 mV CMD Active Level:1711 mV Input file : D:\JTAG Box\EasyJTAG Tool\S3 error\File\EMMC_ROM2_2Mb_BOOT\EMMC_ROM2_00000000_0 0200000.bin Writing 000000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM) Write Speed: 844 kB/s Done !!! ROM1 Skip loading eMMC Addon Firmware CMD Pullup Level:1268 mV CMD Active Level:1722 mV Input file : D:\JTAG Box\EasyJTAG Tool\S3 error\File\EMMC_ROM1_512Mb_USER\EMMC_ROM1_00000000 _20000000.bin Writing 000020000000 bytes to 00000000 ...ROM1 (USER ROM) Write Speed: 2595 kB/s Done !!! <br> at last info lick this eMMC Device Information EMMC CID : 15010056545530304DF1090542D05F28 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 05/2012 Rev.0xf1 EMMC NAME: <b>VTU00M</b> , S/N: 151339728 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_ 151339728_20140901_1900.extcsd Done. But no power on

10-06-2014, 18:21	#39 (permalink)
unlock in nepal No Life Poster Join Date: Nov 2011 Location: Student Posts: 1,225 Member: 1686564 Status: Offline Sonork: PM me Thanks Meter: 157	which backuo file use to to repair extCSD

10-09-2014, 19:04	#42 (permalink)
unlock in nepal No Life Poster Join Date: Nov 2011 Location: Student Posts: 1,225 Member: 1686564 Status: Offline Sonork: PM me Thanks Meter: 157	Healp me fore working file Support file is always no power on i nead tasted rom & working VTU00M_ 792068627_20140103_1914.extcsd file Healp me fore all working file I have same running phone how to read file from ruanning phone healp me

06-06-2014, 19:09	#32 (permalink)
maplegsm No Life Poster Join Date: Nov 2006 Location: Bulgaria/China Age: 58 Posts: 4,312 Member: 391664 Status: Offline Sonork: Python Thanks Meter: 1,063	set is dead .............

06-11-2014, 16:29	#33 (permalink)
drjaved_akhter No Life Poster Join Date: Sep 2007 Location: PAKISTAN Posts: 1,130 Member: 585807 Status: Offline Thanks Meter: 781	i request z3x team please add new update emmc tool logs back up in pc............ thanks

06-11-2015, 22:57	#44 (permalink)
feruzr5 Insane Poster Join Date: Aug 2012 Location: Uzbekistan Age: 38 Posts: 88 Member: 1800327 Status: Offline Thanks Meter: 9	how to repair this eror Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair... Z3X EasyJtag Software ver. 1.9.0.5 Skip loading eMMC Addon Firmware CMD Pullup Level:1268 mV CMD Active Level:3083 mV Repair VTU00M eMMC: Entering repair mode 1... Erasing repair area... Success! Writing repair area... Warning Writing repair area fail Please, Reconnect eMMC power lines and press 'VTU00M Repair' again Done.