SM-G610F FRP This version of "sBoot" is not supported [Solved] - GSM-Forum

sachinc148 · 11-23-2017, 06:45

Welcome to Octoplus Box Samsung software version 2.6.2
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610F
Searching for UART interface.. COM9
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Rebooting phone in Upload Mode...OK
Please connect phone to USB cable..
Searching for a phone. Please wait...OK
Reading data...
Checking operation...
This version of "sBoot" is not supported, try to downgrade "sBoot"!
Operation was failed!
Performed by 2.6.2 Software version.

Can u please help me

Octopus box · 11-23-2017, 06:49

Hello.

Please read attentively Software log and update news:

Quote:

This version of "sBoot" is not supported, try to downgrade "sBoot"!

Quote:

* Note: this operation works for the mentioned above devices with Android 6.x firmwares' versions and may not work for some phones’ S-boot. In this case try to write another firmware version or only S-boot from firmware and repeat the operation again.

For Android 7.x firmwares You cant try to do the following:
1. Write only Sboot (not full firmware) from Android 6.x firmware.
2. Perform "Reset FRP" operation.
3. Write Sboot from Android 7.x firmware.

sachinc148 · 11-23-2017, 07:14

Quote:

Originally Posted by Octopus box

Hello.

Please read attentively Software log and update news:

For Android 7.x firmwares You cant try to do the following:
1. Write only Sboot (not full firmware) from Android 6.x firmware.
2. Perform "Reset FRP" operation.
3. Write Sboot from Android 7.x firmware.

Welcome to Octoplus Box Samsung software version 2.6.2
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610F
Searching for UART interface.. COM9
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Rebooting phone in Upload Mode...OK
Please connect phone to USB cable..
Searching for a phone. Please wait...OK
Reading data...
Checking operation...
This version of "sBoot" is not supported, try to downgrade "sBoot"!
Operation was failed!
Performed by 2.6.2 Software version.
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610F
Searching for a phone (waiting for ADB device)...
Operation was canceled
Performed by 2.6.2 Software version.
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610F
Searching for UART interface.. COM9
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Operation was canceled
Performed by 2.6.2 Software version.
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610F
Searching for UART interface.. COM9
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Rebooting phone in Upload Mode...OK
Please connect phone to USB cable..
Searching for a phone. Please wait...OK
Reading data...
Checking operation...
This version of "sBoot" is not supported, try to downgrade "sBoot"!
Operation was failed!
Performed by 2.6.2 Software version.
Selected firmware file: COMBINATION_ODD_FA60_G610FDDU1API2
_ODDFA60_G610FDDU1API2_CL9139094_QB10968271.oct
Please put the phone into Download Mode and connect USB cable.
To put SM-G610F into Download Mode, You have to perform the
following steps:
1. Reconnect the battery.
2. Press and hold "Volume-" + "Home" + "Power ON" keys.
3. When phone turns on, press "Volume+" key.
Found phone on
Advanced mode!
Firmware write started.
Writing BOOTLOADER section...
BOOTLOADER section has been written successfully.
Firmware writing successfully completed.
Performed by 2.6.2 Software version.
-----------------------------------------------------------------------------------
Platform: Samsung Android
Selected port: COM1
Selected model: SM-G610F
Searching for UART interface.. COM9
Connect Samsung Micro UART cable(with 525K resistor), press and
hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Phone found.
Rebooting phone in Upload Mode...OK
Please connect phone to USB cable..
Searching for a phone. Please wait...
Upload Mode interface not found!
Operation was failed!
Performed by 2.6.2 Software version.

i try this see error

Octopus box · 11-23-2017, 07:23

Why You have written combination firmware? You should write sboot from normal firmware, not from combination firmware.

sachinc148 · 11-23-2017, 07:32

Quote:

Originally Posted by Octopus box

Why You have written combination firmware? You should write sboot from normal firmware, not from combination firmware.

thanks now phone is unlocked

nirmaal · 05-13-2018, 18:30

The best supporting team in the world, that's why I trust Octoplus Box, Thank you million times, *** bless you

Quote:

Originally Posted by Octopus box

Why You have written combination firmware? You should write sboot from normal firmware, not from combination firmware.

Sent from my Nokia 2 using Tapatalk

mostafa220022 · 06-07-2018, 15:29

Quote:

Originally Posted by Octopus box

Hello.

Please read attentively Software log and update news:

For Android 7.x firmwares You cant try to do the following:
1. Write only Sboot (not full firmware) from Android 6.x firmware.
2. Perform "Reset FRP" operation.
3. Write Sboot from Android 7.x firmware.

i try flash just sboot from android 6 but binery error

Octopus box · 06-07-2018, 15:48

Hello.

Post here full Software log with all of performed operations, we will check.

11-23-2017, 06:45	#1 (permalink)
sachinc148 Freak Poster Join Date: Dec 2016 Posts: 112 Member: 2664243 Status: Offline Thanks Meter: 6	SM-G610F FRP This version of "sBoot" is not supported [Solved] Welcome to Octoplus Box Samsung software version 2.6.2 ----------------------------------------------------------------------------------- Platform: Samsung Android Selected port: COM1 Selected model: SM-G610F Searching for UART interface.. COM9 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Phone found. Rebooting phone in Upload Mode...OK Please connect phone to USB cable.. Searching for a phone. Please wait...OK Reading data... Checking operation... This version of "sBoot" is not supported, try to downgrade "sBoot"! Operation was failed! Performed by 2.6.2 Software version. Can u please help me Last edited by Octopus box; 11-23-2017 at 07:33.

11-23-2017, 07:23	#4 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,841 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,411	Why You have written combination firmware? You should write sboot from normal firmware, not from combination firmware.

06-07-2018, 15:48	#8 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,841 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,411	Hello. Post here full Software log with all of performed operations, we will check.