need LCD reset 9630 aka Tour - GSM-Forum

MVNDOzone · 04-06-2013, 07:03

here full info from phone

Quote:

Device Info:
PIN: 30c685xx

Bootrom Version: 5.6.0.19
HW ID Override: None
OS ID: None
Metrics Version: 6.9
Build Date: May 12 2009
Build Time: 15:49:44
Build User: absadmin
Security: Enabled
Supported Options: 0x00000001
Drivers: 0x00000004
Processor: 0x00000008
LDR Blocks: 0x0C00A718
Bootrom Size: 0x00020000
External MCT/HWV: Enabled
Boot Mode: N/A
Boot OS Count: N/A
HWV:
Board Revision 0001 - 0x08
CPU Version 0002 - 0x8D
SW Compatibility 0003 - 0x01
POP Revision 0004 - 0x0C
Power Mgt Hardware 0007 - 0x30
POP Security 000B - 0x01

Mem Config Table (ver 1.16):
Flash Chip: blocks 0-2000, Chip 0, Sub 0
Bootrom: blocks 0-0
OS Dynamic: blocks 2-????
FS Dynamic: blocks ????-1845
Apps EFS: blocks 1846-1925, total = 80
Modem EFS: blocks 1926-1989, total = 64
OS NV: blocks 1990-2000, total 11
CRC: 0x74C84E00

Flash:
Number of chips: 1
Flash ID: NAND blocks 0-2020
Device ID: 0x44
Vendor ID: 0xEC
Version ID: 34
Total Size: 252.6 MB

Memory Map:
NAND Blocks: 2021 * 128 Kb
RAM Base: 0x10000000
IRAM Base: 0x0C000000
OS Range: 2 - 131

File System:
Memory Map:
132 - 1845
Sectors: 1714

Branding:
VendorID: 105

OS Version: 4.1.0.7
Metrics Version: 3.16
FS Code Version: 10.0.0.0
FAT Code Version: 2.23
Package Version: ""
Build Date: Apr 9 2009
Build Time: 18:40:20
Build User: absadmin
SV Number: 16
OS Address: 0x10000000-0x11020C43
App Start: * No Application Linked *

RAM usage: 0x11DFFFFC-0x17FFFFFF
IRAM End: no IRAM!
DSP ROM2 Address: *not present*
OS Extended Addr: 0x00000000
LDR Blocks: 0x10000718

API Checksum: 0x00000000
JumpTable (<3): 0x00000000
JumpTable (>2): 0x00000000

Radio Code: Eltron5 radio code linked
OS API Version: 115.0
STP Protocol Ver: 5.146.1 (factory OS)

HWV:
Board Revision 0001 - 0x02 - 0xFF, 0x01
POP Revision 0004 - 0x00 - 0xFF, 0x01
CPU Version 0002 - 0x00 - 0x8B, 0x01
CPU Version 0002 - 0x8D - 0xFF, 0x01
SW Compatibility 0003 - 0x00 - 0x01, 0x01
Power Mgt Hardware 0007 - 0x03 - 0xFF, 0x01

Version Table:
OS API Version: 115.0
STP protocol version: 5.146.1
BlockFS API Version: 10.0.0.0
USB driver version: 01.07
Block map version: 2.12

Done.

thanks advance

Shensohau · 04-06-2013, 15:32

Bro just use one of the zzkey files on support, just use the higher one.... try and post it! I think that 9630 just use one type of LCD....

MVNDOzone · 04-07-2013, 14:27

i was use 9630_13.zFlash
but not reset

this type have type 1 lcd 004
LCD 8900 is same but have serial 002

i have LCD 8900 002 in stock
i want to reset 9630 to 8900

thanks

Shensohau · 04-07-2013, 16:22

well man, try this use one LCD 004 serie on 9630 and reset 8900 and put on it 002 LCD and solve your problem!!!!

04-06-2013, 15:32	#2 (permalink)
Shensohau No Life Poster Join Date: Aug 2010 Location: Inside Logic Age: 37 Posts: 5,882 Member: 1377783 Status: Offline Sonork: 100.1611724 Thanks Meter: 3,336	Bro just use one of the zzkey files on support, just use the higher one.... try and post it! I think that 9630 just use one type of LCD....

04-07-2013, 14:27	#3 (permalink)
MVNDOzone No Life Poster Join Date: Aug 2010 Posts: 596 Member: 1372118 Status: Offline Thanks Meter: 139	i was use 9630_13.zFlash but not reset this type have type 1 lcd 004 LCD 8900 is same but have serial 002 i have LCD 8900 002 in stock i want to reset 9630 to 8900 thanks

04-07-2013, 16:22	#4 (permalink)
Shensohau No Life Poster Join Date: Aug 2010 Location: Inside Logic Age: 37 Posts: 5,882 Member: 1377783 Status: Offline Sonork: 100.1611724 Thanks Meter: 3,336	well man, try this use one LCD 004 serie on 9630 and reset 8900 and put on it 002 LCD and solve your problem!!!!