celkon a9+ pattern lock done With Power Full Box Volcano
 

Detection initiated...
Vcc: null
Gnd: 5
Analyzing D+ and D-...
D+ = 3, D- = 2
Detection D+/D- with 1.38 seconds.
Continue to detect BOOT pin...
Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
Setting...
Find USB device:SPRD U2S Diag (COM124), (VID_1782&PID_4D00)
Pinouts setting complete!

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 009800BC90667600
Flash Type:[TOSHIBA] TYBC0A111236KC10
FLASH LEN:0x20000000
mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),10m(modem),3840k(fixnv),3840k(backupfixnv),51 20k(dsp),3840k(runtimenv),10m(boot),10m(recovery), 215m(system),175m(userdata),60m(cache),256k(misc), 1m(boot_logo),1m(fastboot_logo),3840k(productinfo) ,512k(kpanic)
Analysis flash internal data successfully.
Set to Factory successfully

How to remove pattern Unlock celkon A9+

Make hard reset to your mobile.

Thank you so so so so much VOLCANO .
i solved my problem
It works

ceikon A9+ patternlock removed by valcono.v. 2.2.1.1 very easy to all my freinds,take care enioy
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00EC00BC00555400
Flash Type:[SAMSUNG] K9F4G08/K9K4G08
FLASH LEN:0x20000000
mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),10m(modem),3840k(fixnv),3840k(backupfixnv),51 20k(dsp),3840k(runtimenv),10m(boot),10m(recovery), 215m(system),175m(userdata),60m(cache),256k(misc), 1m(boot_logo),1m(fastboot_logo),3840k(productinfo) ,512k(kpanic)
Analysis flash internal data successfully.
>>Set to Factory successfully.

volcano box best box
 

volcano box best box

thanks for feed back bro , also post here

http://forum.gsmhosting.com/vbb/f723...hones-1432745/

celkon A9+ hard reset
 

done with valcano v2.0.0

celcon A9+ PATTERN UNLOCK / HARD RESET


use volcano tool version 1.9.8

SELECT SPD

TICK FORMAT

SELECT AUTO DETECT PINOUTS

NOW CLICK RUN

AND THE RESULT IS................

Connecting...
Connection successful,connected state!
Version: V3.8
SN:183-846-794
Port:COM18
After format or Flash you have to press & hold power button for at least 1.30 mins.
Available Ports:COM4 COM18
Detection initiated...
Vcc: null
Gnd: 24
Analyzing D+ and D-...
D+ = 22, D- = 21
Analyzing USB device, please wait...
Find USB device:SCI USB2Serial (COM37), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 009800BC
FLASH LEN:0x20000000
Set to Factory successfully.

i have tried many times and it was successful.

ENJOY.

cekkon a9+ hard reset by volcano
 

thanks valcano team its working 1000000000000000%


Analyzing D+ and D-...
D+ = 3, D- = 2
Analyzing USB device, please wait...
Find USB device:SCI USB2Serial (COM18), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 009800BC
FLASH LEN:0x20000000
Set to Factory successfully.

sir when i try to flash without read flash i formatted celkon a9+ with volcano box dead how to solve this problem please tell me? thanks

I have one problem with a9+
Analysis flash internal data fail.
But had sucess with other sets this one is not working pls helo .

bro try to flash with firmware :)

me to same problam plz help team members

problam solve just formatt 2.0.0 ver. see this Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00EC00BC
Flash Type:[SAMSUNG] K9F4G08/K9K4G08
FLASH LEN:0x20000000
>>Set to Factory successfully.