z.doxio i9082 dead after format - GSM-Forum

fantomasv · 08-20-2014, 05:04

please help me dead after format, i wil do full flash but i don`t how to reflash please help i load full flash but any needed

Volcano Updated: 2014-07-26
Connecting...
Connection successful,connected state!
Version: V3.8
SN:682-080-186
Port:COM48
After format or Flash you have to press & hold power button for at least 1.30 mins.
Note for win7 users :
Start your Win 7 64bit with F8 key and choose 'Disable Driver Signature Enforcement'.
After that the spd drivers will have the ability to be loaded.
For many phones, charge pins need to be set in order to identify USB devices.
Detecting D+ and D-...
Vcc: null
Gnd: null
Detection initiated...
Found: D+ = 4, D- = 3
Detection D+/D- with 3,13 seconds!
Analyzing USB device, please wait...
Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
Detection completed.
Available Ports:COM1 COM48
Detection initiated...
Vcc: null
Gnd: 6 7
Analyzing D+ and D-...
D+ = 4, D- = 3
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00C800BC90555400
FLASH LEN:0x20000000
Please read the phone partition.
Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.
Detection initiated...
Vcc: null
Gnd: 6 7
Analyzing D+ and D-...
D+ = 4, D- = 3
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00C800BC90555400
FLASH LEN:0x20000000
mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),4m(modem),3840k(fixnv),3840k(backupfixnv),512 0k(dsp),3840k(runtimenv),10m(boot),10m(recovery),2 16m(system),170m(userdata),60m(cache),256k(misc),1 m(boot_logo),1m(fastboot_logo),3840k(productinfo), 512k(kpanic),512k(simlock),10m(intmemory)
Analysis flash internal data successfully.
Detection initiated...
Vcc: null
Gnd: 6 7
Analyzing D+ and D-...
D+ = 4, D- = 3
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00C800BC90555400
FLASH LEN:0x20000000
Please read the phone partition.
Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.
Detection initiated...
Vcc: null
Gnd: 6 7
Analyzing D+ and D-...
D+ = 4, D- = 3
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),4m(modem),3840k(fixnv),3840k(backupfixnv),512 0k(dsp),3840k(runtimenv),10m(boot),10m(recovery),2 16m(system),170m(userdata),60m(cache),256k(misc),1 m(boot_logo),1m(fastboot_logo),3840k(productinfo), 512k(kpanic),512k(simlock),10m(intmemory)
Analysis flash internal data successfully.
Set to Factory successfully.
Detection initiated...
Vcc: null
Gnd: 6 7
Analyzing D+ and D-...
D+ = 4, D- = 3
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00C800BC90555400
FLASH LEN:0x20000000
Please read the phone partition.
>>Ready to read/write again, please remove the power supply clip or battery and then re-loaded itore you received this error.

fantomasv · 08-25-2014, 23:58

i have 2 phones in same dead

kervicell · 08-26-2014, 00:24

p-05 pcb plug boot 6820 when I tell precionar precionado keep power down volume generates a port there and will continue its work

fantomasv · 08-27-2014, 02:34

how to revive my phones?

fantomasv · 09-03-2014, 21:44

never help team trash volcano its a nothing

ashaka · 09-04-2014, 09:50

Quote:

Originally Posted by fantomasv

never help team trash volcano its a nothing

only way is to look for factory file my friend

ali_GSM98 · 09-04-2014, 09:52

i have 2 phones in same problem & set dead??????????????????????
???????????????????????

08-20-2014, 05:04	#1 (permalink)
fantomasv Freak Poster Join Date: Jan 2005 Location: mexico city Age: 52 Posts: 359 Member: 106488 Status: Offline Thanks Meter: 24	z.doxio i9082 dead after format please help me dead after format, i wil do full flash but i don`t how to reflash please help i load full flash but any needed Volcano Updated: 2014-07-26 Connecting... Connection successful,connected state! Version: V3.8 SN:682-080-186 Port:COM48 After format or Flash you have to press & hold power button for at least 1.30 mins. Note for win7 users : Start your Win 7 64bit with F8 key and choose 'Disable Driver Signature Enforcement'. After that the spd drivers will have the ability to be loaded. For many phones, charge pins need to be set in order to identify USB devices. Detecting D+ and D-... Vcc: null Gnd: null Detection initiated... Found: D+ = 4, D- = 3 Detection D+/D- with 3,13 seconds! Analyzing USB device, please wait... Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00) Detection completed. Available Ports:COM1 COM48 Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. Flash ID: 00C800BC90555400 FLASH LEN:0x20000000 Please read the phone partition. Ready to read/write again, please remove the power supply clip or battery and then re-loaded it. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. Flash ID: 00C800BC90555400 FLASH LEN:0x20000000 mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),4m(modem),3840k(fixnv),3840k(backupfixnv),512 0k(dsp),3840k(runtimenv),10m(boot),10m(recovery),2 16m(system),170m(userdata),60m(cache),256k(misc),1 m(boot_logo),1m(fastboot_logo),3840k(productinfo), 512k(kpanic),512k(simlock),10m(intmemory) Analysis flash internal data successfully. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. Flash ID: 00C800BC90555400 FLASH LEN:0x20000000 Please read the phone partition. Ready to read/write again, please remove the power supply clip or battery and then re-loaded it. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),4m(modem),3840k(fixnv),3840k(backupfixnv),512 0k(dsp),3840k(runtimenv),10m(boot),10m(recovery),2 16m(system),170m(userdata),60m(cache),256k(misc),1 m(boot_logo),1m(fastboot_logo),3840k(productinfo), 512k(kpanic),512k(simlock),10m(intmemory) Analysis flash internal data successfully. Set to Factory successfully. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM233), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. Flash ID: 00C800BC90555400 FLASH LEN:0x20000000 Please read the phone partition. >>Ready to read/write again, please remove the power supply clip or battery and then re-loaded itore you received this error.

08-25-2014, 23:58	#2 (permalink)
fantomasv Freak Poster Join Date: Jan 2005 Location: mexico city Age: 52 Posts: 359 Member: 106488 Status: Offline Thanks Meter: 24	team volcano answer please i have 2 phones in same dead

08-27-2014, 02:34	#4 (permalink)
fantomasv Freak Poster Join Date: Jan 2005 Location: mexico city Age: 52 Posts: 359 Member: 106488 Status: Offline Thanks Meter: 24	please help volcano box how to revive my phones?

09-03-2014, 21:44	#5 (permalink)
fantomasv Freak Poster Join Date: Jan 2005 Location: mexico city Age: 52 Posts: 359 Member: 106488 Status: Offline Thanks Meter: 24	volcano box are box trash never help team trash volcano its a nothing

08-26-2014, 00:24	#3 (permalink)
kervicell Freak Poster Join Date: Oct 2012 Location: transilvania Posts: 355 Member: 1820429 Status: Offline Thanks Meter: 57	p-05 pcb plug boot 6820 when I tell precionar precionado keep power down volume generates a port there and will continue its work

09-04-2014, 09:52	#7 (permalink)
ali_GSM98 Freak Poster Join Date: Jun 2013 Location: south Africa Posts: 319 Member: 1960717 Status: Offline Sonork: 100.1638403 Thanks Meter: 34	i have 2 phones in same problem & set dead?????????????????????? ???????????????????????