|
Welcome to the GSM-Forum forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. Only registered members may post questions, contact other members or search our database of over 8 million posts. Registration is fast, simple and absolutely free so please - Click to REGISTER! If you have any problems with the registration process or your account login, please contact contact us . |
|
Register | FAQ | Donate | Forum Rules | Root any Device | ★iPhone Unlock★ | ★ Direct Codes ★ | Direct Unlock Source |
| LinkBack | Thread Tools | Display Modes |
11-02-2018, 20:05 | #1 (permalink) |
Freak Poster Join Date: Feb 2012 Location: Cuba
Posts: 165
Member: 1718709 Status: Offline Thanks Meter: 10 | LG LS770 cannot connect [Answered] Trying to connect ls770 but box says: no tarjet device ... Code: Welcome to Medusa Pro Software version 1.6.9. Started. Reader #0: Alcor Micro USB Smart Card Reader 0 Reader #1: FT SCR2000 0 Reader #2: FT SCR2000 1 Please disconnect battery and USB cable. Model Settings: Interface : eMMC Brand : LG Model : LS770 SRF : C:/Program Files (x86)/Medusa Pro Software/firmwareFolder/LG_LS770_EMMC_QN1SMB.srf Voltage : 1.8V Bus Mode : 1 bit Bus speed : Auto Connecting... ERROR[001]: Can not connect. No target device present. Please disconnect battery and USB cable. Model Settings: Interface : eMMC Brand : LG Model : LS770 SRF : C:/Program Files (x86)/Medusa Pro Software/firmwareFolder/LG_LS770_EMMC_QN1SMB.srf Voltage : 1.8V Bus Mode : 1 bit Bus speed : Auto Connecting... ERROR[001]: Can not connect. No target device present. Please disconnect battery and USB cable. Model Settings: Interface : eMMC Brand : LG Model : LS770 SRF : C:/Program Files (x86)/Medusa Pro Software/firmwareFolder/LG_LS770_EMMC_QN1SMB.srf Voltage : 1.8V Bus Mode : 1 bit Bus speed : Auto Connecting... ERROR[001]: Can not connect. No target device present. Please disconnect battery and USB cable. Model Settings: Interface : eMMC Brand : LG Model : LS770 SRF : C:/Program Files (x86)/Medusa Pro Software/firmwareFolder/LG_LS770_EMMC_QN1SMB.srf Voltage : 1.8V Bus Mode : 1 bit Bus speed : Auto Connecting... ERROR[001]: Can not connect. No target device present. i note than memory is skhynix instead of samsung, there is possible to connect whit medusa pro box??? Thanks in advance!!! Last edited by Octopus box; 11-03-2018 at 11:02. |
The Following User Says Thank You to MovilesTomasito For This Useful Post: |
11-03-2018, 11:01 | #2 (permalink) |
Product Supporter Join Date: Mar 2011 Location: Octopus-team
Posts: 9,360
Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks Meter: 3,398 | Hello. Here are a few main possible reasons why the device may not connect: 1. You have connected battery or USB cable. Before connecting the device You must disconnect the battery and the USB cable, and then connect the device without power, this is important! 2. Some wires are soldered incorrectly. Carefully check soldering of all wires. 3. In the process of soldering, the resistors were burned (damaged) by using soldering iron or the pin pads on the board to which wires were soldered were damaged. Need replace damaged resistors and restore the pin pads on the board. 4. The ends of wires that were soldered, had not been cleared. Wire, that comes complete with Medusa Pro Box, is covered with an insulator, so before soldering need to clean the ends of each wire. 5. Soldered wires are too long. Make each wire as short as possible (3-5 CM length). 6. For GND connection use more thicker wire. Check all of them and try to connect the device again. |
11-03-2018, 20:04 | #3 (permalink) |
Freak Poster Join Date: Feb 2012 Location: Cuba
Posts: 165
Member: 1718709 Status: Offline Thanks Meter: 10 | i read many post before asking, but question is memory of the device is skhynix and the memory of the picture on medusa box software is samsung emmc, so i try this on many 4 lg models all whit skhynix emmc, and after hours of work cannot connect any of them, so i need to do something else, also, medusa box connect ok whit devices with samsung emmc, so please team help, thanks!!!! Last edited by Octopus box; 11-04-2018 at 12:26. |
11-04-2018, 12:30 | #4 (permalink) |
Product Supporter Join Date: Mar 2011 Location: Octopus-team
Posts: 9,360
Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks Meter: 3,398 | The problme not with eMMC vendor, the problme is with eMMC (HW problem) or with connection. If You are sure You have soldered all wireas correctly, try to remove eMMC and solder all wires directly to eMMC contacts (or use proper eMMC adapter) and try to connect directly. |
11-05-2018, 20:10 | #5 (permalink) |
Freak Poster Join Date: Feb 2012 Location: Cuba
Posts: 165
Member: 1718709 Status: Offline Thanks Meter: 10 | thanks team for reply, this hapen to me on 4 lg board until now, only whit lg boards, i connect medusa ok whit other brands boards, so maybe in the next lg i try again!! thanks for reply! |
The Following User Says Thank You to MovilesTomasito For This Useful Post: |
Bookmarks |
| |
|