j110h dead boot not solve [Answered] - GSM-Forum

alimobile279 · 04-20-2019, 10:57

Welcome to Octoplus Pro JTAG Software version 1.7.6. Started.
Reader #0: Alcor Micro USB Smart Card Reader 0
Reader #1: Broadcom Corp Contacted SmartCard 0

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Brand : Samsung
Model : SM-J110H
SRF : C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Hynix eMMC H4G2b
Page size : 512 B
Block size : 512 B
Block count : 7634944
Size : 3728.00 MB
---------------------------------------------------------------
CID Info

CID : 90014A4834473262110142E04C5F4353
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : H4G2b
Product revision : 0.1
Product serial number : (hex) 42E04C5F
Manufacturing date : 04/2016
---------------------------------------------------------------
CSD Info

CSD : D07F01320F5903FFFFFFFFEF8A4040DB
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 80 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.6 (for MMC v4.5, v4.51)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : (0x08) 00001000
Boot partition enable : Boot partition 1
(Bus width = 1Bit)
Boot ACK : No boot acknowledge sent (default)

Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 1908736 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...
Not found
---------------------------------------------------------------
Backup EXT_CSD saved to file C:/Program Files/Octoplus Pro JTAG Software/EXT_CSD Backups/H4G2b_20_04_2019_14_54_19.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.7.6; FW: 1.24.
P00: GPT (00000000, 00002000) 4 MB
P01: SBOOT (00002000, 00001000) 2048 KB
P02: SBOOT2 (00003000, 00001000) 2048 KB
P03: wfixnv1 (00004000, 00000800) 1024 KB
P04: wfixnv2 (00004800, 00000800) 1024 KB
P05: tdfixnv1 (00005000, 00000800) 1024 KB
P06: tdfixnv2 (00005800, 00000800) 1024 KB
P07: WDSP (00006000, 00002000) 4 MB
P08: MODEM (00008000, 00004000) 8 MB
P09: MODEM2 (0000C000, 00004000) 8 MB
P10: TDDSP (00010000, 00002000) 4 MB
P11: FOTA_SIG (00012000, 00000800) 1024 KB
P12: wruntimenv1 (00012800, 00000800) 1024 KB
P13: wruntimenv2 (00013000, 00000800) 1024 KB
P14: tdruntimenv1 (00013800, 00000800) 1024 KB
P15: tdruntimenv2 (00014000, 00000800) 1024 KB
P16: PARAM (00014800, 00001000) 2048 KB
P17: EFS (00015800, 0000A000) 20 MB
P18: PRODNV (0001F800, 00002800) 5 MB
P19: RESERVED2 (00022000, 00000800) 1024 KB
P20: KERNEL (00022800, 00008000) 16 MB
P21: RECOVERY (0002A800, 00008000) 16 MB
P22: PERSDATA (00032800, 00004800) 9 MB
P23: CSC (00037000, 00064000) 200 MB
P24: SYSTEM (0009B000, 00203000) 1030 MB
P25: HIDDEN (0029E000, 0001D000) 58 MB
P26: USERDATA (002BB000, 00486000) 2316 MB

Selected pit file: C:/Users/alimobile/Desktop/J110HXXU0AOGA_OXE0AOGC_v4.4.4_Repair_Firmware/J1POP3G.pit

Open file "C:/Users/alimobile/Desktop/J110HXXU0AOGA_OXE0AOGC_v4.4.4_Repair_Firmware/BL_J110HXXU0AOGA_CL737598_QB5784505_REV02_user_low _ship.tar.md5".

Writing MBR...Done.
Writing primary GPT...Done.
Writing secondary GPT...
ERROR[012]: Write error.
At sector 7634911.
Disconnected.

starkrimes · 04-20-2019, 11:04

try perform repairing with data verification Disabled

alimobile279 · 04-20-2019, 12:06

no power
Welcome to Octoplus Pro JTAG Software version 1.7.6.
Started.
Reader #0: Alcor Micro USB Smart Card Reader 0
Reader #1: Alcor Micro USB Smart Card Reader 1
Reader #2: Broadcom Corp Contacted SmartCard 0

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Brand : Samsung
Model : SM-J110H
SRF : C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Hynix eMMC H4G2b
Page size : 512 B
Block size : 512 B
Block count : 7634944
Size : 3728.00 MB
---------------------------------------------------------------
CID Info

CID : 90014A4834473262110142E04C5F4353
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : H4G2b
Product revision : 0.1
Product serial number : (hex) 42E04C5F
Manufacturing date : 04/2016
---------------------------------------------------------------
CSD Info

CSD : D07F01320F5903FFFFFFFFEF8A4040DB
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 80 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.6 (for MMC v4.5, v4.51)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : (0x08) 00001000
Boot partition enable : Boot partition 1
(Bus width = 1Bit)
Boot ACK : No boot acknowledge sent (default)

Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 1908736 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...
Not found
---------------------------------------------------------------
Backup EXT_CSD saved to file C:/Program Files/Octoplus Pro JTAG Software/EXT_CSD Backups/H4G2b_20_04_2019_16_03_02.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.7.6; FW: 1.24.
P00: GPT (00000000, 00002000) 4 MB
P01: SBOOT (00002000, 00001000) 2048 KB
P02: SBOOT2 (00003000, 00001000) 2048 KB
P03: wfixnv1 (00004000, 00000800) 1024 KB
P04: wfixnv2 (00004800, 00000800) 1024 KB
P05: tdfixnv1 (00005000, 00000800) 1024 KB
P06: tdfixnv2 (00005800, 00000800) 1024 KB
P07: WDSP (00006000, 00002000) 4 MB
P08: MODEM (00008000, 00004000) 8 MB
P09: MODEM2 (0000C000, 00004000) 8 MB
P10: TDDSP (00010000, 00002000) 4 MB
P11: FOTA_SIG (00012000, 00000800) 1024 KB
P12: wruntimenv1 (00012800, 00000800) 1024 KB
P13: wruntimenv2 (00013000, 00000800) 1024 KB
P14: tdruntimenv1 (00013800, 00000800) 1024 KB
P15: tdruntimenv2 (00014000, 00000800) 1024 KB
P16: PARAM (00014800, 00001000) 2048 KB
P17: EFS (00015800, 0000A000) 20 MB
P18: PRODNV (0001F800, 00002800) 5 MB
P19: RESERVED2 (00022000, 00000800) 1024 KB
P20: KERNEL (00022800, 00008000) 16 MB
P21: RECOVERY (0002A800, 00008000) 16 MB
P22: PERSDATA (00032800, 00004800) 9 MB
P23: CSC (00037000, 00064000) 200 MB
P24: SYSTEM (0009B000, 00203000) 1030 MB
P25: HIDDEN (0029E000, 0001D000) 58 MB
P26: USERDATA (002BB000, 00486000) 2316 MB
Repairing from file "C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf".
Write data verification is enabled.

Switched to boot area partition 1.
Writing BOOT1 partition... Done.

Switched to boot area partition 2.
Writing BOOT2 partition... Done.

Switched to user area.
Writing GPT partition... Done.
Writing SBOOT partition... Done.
Writing SBOOT2 partition... Done.
Writing wfixnv1 partition... Done.
Writing wfixnv2 partition... Done.
Writing tdfixnv1 partition... Done.
Writing tdfixnv2 partition... Done.
Writing WDSP partition... Done.
Writing MODEM partition... Done.
Writing MODEM2 partition... Done.
Writing TDDSP partition... Done.
Writing FOTA_SIG partition... Done.
Writing wruntimenv1 partition... Done.
Writing wruntimenv2 partition... Done.
Writing tdruntimenv1 partition... Done.
Writing tdruntimenv2 partition... Done.
Writing PARAM partition... Done.
Writing EFS partition... Done.
Writing PRODNV partition... Done.
Writing RESERVED2 partition... Done.
Writing KERNEL partition... Done.
Writing RECOVERY partition... Done.
Writing PERSDATA partition... Done.
Writing CSC partition... Done.

Smart Repair is successfully complete.
SW: 1.7.6; FW: 1.24.
Disconnected.

starkrimes · 04-20-2019, 12:29

Quote:

Originally Posted by alimobile279

no power
Welcome to Octoplus Pro JTAG Software version 1.7.6.
Started.
Reader #0: Alcor Micro USB Smart Card Reader 0
Reader #1: Alcor Micro USB Smart Card Reader 1
Reader #2: Broadcom Corp Contacted SmartCard 0

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Brand : Samsung
Model : SM-J110H
SRF : C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Hynix eMMC H4G2b
Page size : 512 B
Block size : 512 B
Block count : 7634944
Size : 3728.00 MB
---------------------------------------------------------------
CID Info

CID : 90014A4834473262110142E04C5F4353
Manufacturer ID : 0X90
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X4A
Product name : H4G2b
Product revision : 0.1
Product serial number : (hex) 42E04C5F
Manufacturing date : 04/2016
---------------------------------------------------------------
CSD Info

CSD : D07F01320F5903FFFFFFFFEF8A4040DB
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 80 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.6 (for MMC v4.5, v4.51)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : (0x08) 00001000
Boot partition enable : Boot partition 1
(Bus width = 1Bit)
Boot ACK : No boot acknowledge sent (default)

Boot bus conditions : (0x00) 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 1908736 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...
Not found
---------------------------------------------------------------
Backup EXT_CSD saved to file C:/Program Files/Octoplus Pro JTAG Software/EXT_CSD Backups/H4G2b_20_04_2019_16_03_02.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.7.6; FW: 1.24.
P00: GPT (00000000, 00002000) 4 MB
P01: SBOOT (00002000, 00001000) 2048 KB
P02: SBOOT2 (00003000, 00001000) 2048 KB
P03: wfixnv1 (00004000, 00000800) 1024 KB
P04: wfixnv2 (00004800, 00000800) 1024 KB
P05: tdfixnv1 (00005000, 00000800) 1024 KB
P06: tdfixnv2 (00005800, 00000800) 1024 KB
P07: WDSP (00006000, 00002000) 4 MB
P08: MODEM (00008000, 00004000) 8 MB
P09: MODEM2 (0000C000, 00004000) 8 MB
P10: TDDSP (00010000, 00002000) 4 MB
P11: FOTA_SIG (00012000, 00000800) 1024 KB
P12: wruntimenv1 (00012800, 00000800) 1024 KB
P13: wruntimenv2 (00013000, 00000800) 1024 KB
P14: tdruntimenv1 (00013800, 00000800) 1024 KB
P15: tdruntimenv2 (00014000, 00000800) 1024 KB
P16: PARAM (00014800, 00001000) 2048 KB
P17: EFS (00015800, 0000A000) 20 MB
P18: PRODNV (0001F800, 00002800) 5 MB
P19: RESERVED2 (00022000, 00000800) 1024 KB
P20: KERNEL (00022800, 00008000) 16 MB
P21: RECOVERY (0002A800, 00008000) 16 MB
P22: PERSDATA (00032800, 00004800) 9 MB
P23: CSC (00037000, 00064000) 200 MB
P24: SYSTEM (0009B000, 00203000) 1030 MB
P25: HIDDEN (0029E000, 0001D000) 58 MB
P26: USERDATA (002BB000, 00486000) 2316 MB
Repairing from file "C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf".
Write data verification is enabled.

Switched to boot area partition 1.
Writing BOOT1 partition... Done.

Switched to boot area partition 2.
Writing BOOT2 partition... Done.

Switched to user area.
Writing GPT partition... Done.
Writing SBOOT partition... Done.
Writing SBOOT2 partition... Done.
Writing wfixnv1 partition... Done.
Writing wfixnv2 partition... Done.
Writing tdfixnv1 partition... Done.
Writing tdfixnv2 partition... Done.
Writing WDSP partition... Done.
Writing MODEM partition... Done.
Writing MODEM2 partition... Done.
Writing TDDSP partition... Done.
Writing FOTA_SIG partition... Done.
Writing wruntimenv1 partition... Done.
Writing wruntimenv2 partition... Done.
Writing tdruntimenv1 partition... Done.
Writing tdruntimenv2 partition... Done.
Writing PARAM partition... Done.
Writing EFS partition... Done.
Writing PRODNV partition... Done.
Writing RESERVED2 partition... Done.
Writing KERNEL partition... Done.
Writing RECOVERY partition... Done.
Writing PERSDATA partition... Done.
Writing CSC partition... Done.

Smart Repair is successfully complete.
SW: 1.7.6; FW: 1.24.
Disconnected.

so i see you did your job
phone is working?

alimobile279 · 04-20-2019, 13:03

not working no power on.................

starkrimes · 04-20-2019, 13:24

Quote:

Originally Posted by alimobile279

not working no power on.................

what was the phone status before u performed the eMMC REPAIR

rebainoor · 04-20-2019, 16:21

Hi
for j110h to resolve "ERROR[012]: Write error"

after successefull connected in emmc mode go to EMMC service tab and clic in HW Partitions and do not change any think and clic in write
after that you will get this :

Code:

No General Purpose Partition 1
	enhanced attribute is not set
	write reliablity is set

No General Purpose Partition 2
	enhanced attribute is not set
	write reliablity is set

No General Purpose Partition 3
	enhanced attribute is not set
	write reliablity is set

No General Purpose Partition 4
	enhanced attribute is not set
	write reliablity is set

No enhanced user data area
	write reliablity is not set
Creating HW partitions succesfully complete!

and you need reconnect emmc and do factory repair with last firmware version only

you can see in this post : http://forum.gsmhosting.com/vbb/f664...olved-2541073/

04-20-2019, 10:57	#1 (permalink)
alimobile279 No Life Poster Join Date: Mar 2011 Location: Faisalabad Posts: 1,482 Member: 1527968 Status: Offline Sonork: 100.1651182 Thanks Meter: 483	j110h dead boot not solve [Answered] Welcome to Octoplus Pro JTAG Software version 1.7.6. Started. Reader #0: Alcor Micro USB Smart Card Reader 0 Reader #1: Broadcom Corp Contacted SmartCard 0 Please disconnect battery and USB cable. Model Settings: Interface : eMMC Brand : Samsung Model : SM-J110H SRF : C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf Voltage : 1.8V Bus Mode : 1 bit Bus speed : Auto Connecting... Device : Hynix eMMC H4G2b Page size : 512 B Block size : 512 B Block count : 7634944 Size : 3728.00 MB --------------------------------------------------------------- CID Info CID : 90014A4834473262110142E04C5F4353 Manufacturer ID : 0X90 Device/BGA : BGA (Discrete embedded) OEM/Application ID : 0X4A Product name : H4G2b Product revision : 0.1 Product serial number : (hex) 42E04C5F Manufacturing date : 04/2016 --------------------------------------------------------------- CSD Info CSD : D07F01320F5903FFFFFFFFEF8A4040DB CSD structure : CSD version No. 1.2 SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5, 4.51, 5.0, 5.01, 5.1 Data read access time1: 80 ms TRAN speed : 26 MHz READ block length : 512 Bytes WP group enable : YES PERM_WRITE_PROTECT : NO TMP_WRITE_PROTECT : NO --------------------------------------------------------------- EXTCSD Info Revision 1.6 (for MMC v4.5, v4.51) Erase block size : 512 Kbytes Boot1 size : 4096 Kbytes Boot2 size : 4096 Kbytes RPMB size : 4096 Kbytes Partition config : (0x08) 00001000 Boot partition enable : Boot partition 1 (Bus width = 1Bit) Boot ACK : No boot acknowledge sent (default) Boot bus conditions : (0x00) 00000000 Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default) Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default) Boot mode : Use single data rate + backward compatible timings in boot operation (default) RST_n function : (0x00) RST_n signal is temporary disabled (default) Partitioning support : Device supports partitioning features Enhanced attribute : Device can have enhanced technological features in partitions and user data area. Max enhanced data size: 1908736 Kbytes Partitions attribute : 0x0 Part setting completed: 0x0 GP partition 1 size : 0 b GP partition 2 size : 0 b GP partition 3 size : 0 b GP partition 4 size : 0 b Enhanced area size : (0x0) 0 b Enhanced area start : (0x0) 0 b ---------------------------------------------------------------Searching Android build info... Not found --------------------------------------------------------------- Backup EXT_CSD saved to file C:/Program Files/Octoplus Pro JTAG Software/EXT_CSD Backups/H4G2b_20_04_2019_14_54_19.bin. Connect successful. --------------------------------------------------------------- SW: 1.7.6; FW: 1.24. P00: GPT (00000000, 00002000) 4 MB P01: SBOOT (00002000, 00001000) 2048 KB P02: SBOOT2 (00003000, 00001000) 2048 KB P03: wfixnv1 (00004000, 00000800) 1024 KB P04: wfixnv2 (00004800, 00000800) 1024 KB P05: tdfixnv1 (00005000, 00000800) 1024 KB P06: tdfixnv2 (00005800, 00000800) 1024 KB P07: WDSP (00006000, 00002000) 4 MB P08: MODEM (00008000, 00004000) 8 MB P09: MODEM2 (0000C000, 00004000) 8 MB P10: TDDSP (00010000, 00002000) 4 MB P11: FOTA_SIG (00012000, 00000800) 1024 KB P12: wruntimenv1 (00012800, 00000800) 1024 KB P13: wruntimenv2 (00013000, 00000800) 1024 KB P14: tdruntimenv1 (00013800, 00000800) 1024 KB P15: tdruntimenv2 (00014000, 00000800) 1024 KB P16: PARAM (00014800, 00001000) 2048 KB P17: EFS (00015800, 0000A000) 20 MB P18: PRODNV (0001F800, 00002800) 5 MB P19: RESERVED2 (00022000, 00000800) 1024 KB P20: KERNEL (00022800, 00008000) 16 MB P21: RECOVERY (0002A800, 00008000) 16 MB P22: PERSDATA (00032800, 00004800) 9 MB P23: CSC (00037000, 00064000) 200 MB P24: SYSTEM (0009B000, 00203000) 1030 MB P25: HIDDEN (0029E000, 0001D000) 58 MB P26: USERDATA (002BB000, 00486000) 2316 MB Selected pit file: C:/Users/alimobile/Desktop/J110HXXU0AOGA_OXE0AOGC_v4.4.4_Repair_Firmware/J1POP3G.pit Open file "C:/Users/alimobile/Desktop/J110HXXU0AOGA_OXE0AOGC_v4.4.4_Repair_Firmware/BL_J110HXXU0AOGA_CL737598_QB5784505_REV02_user_low _ship.tar.md5". Writing MBR...Done. Writing primary GPT...Done. Writing secondary GPT... ERROR[012]: Write error. At sector 7634911. Disconnected.

04-20-2019, 16:21	#7 (permalink)
rebainoor No Life Poster Join Date: Feb 2006 Location: In my LAB Posts: 3,163 Member: 231728 Status: Offline Thanks Meter: 2,103	Hi for j110h to resolve "ERROR[012]: Write error" after successefull connected in emmc mode go to EMMC service tab and clic in HW Partitions and do not change any think and clic in write after that you will get this : Code: No General Purpose Partition 1 enhanced attribute is not set write reliablity is set No General Purpose Partition 2 enhanced attribute is not set write reliablity is set No General Purpose Partition 3 enhanced attribute is not set write reliablity is set No General Purpose Partition 4 enhanced attribute is not set write reliablity is set No enhanced user data area write reliablity is not set Creating HW partitions succesfully complete! and you need reconnect emmc and do factory repair with last firmware version only you can see in this post : http://forum.gsmhosting.com/vbb/f664...olved-2541073/

04-20-2019, 11:04	#2 (permalink)
starkrimes No Life Poster Join Date: Dec 2009 Location: Laghouat, Algeria Age: 30 Posts: 541 Member: 1191316 Status: Offline Thanks Meter: 900	try perform repairing with data verification Disabled

04-20-2019, 12:06	#3 (permalink)
alimobile279 No Life Poster Join Date: Mar 2011 Location: Faisalabad Posts: 1,482 Member: 1527968 Status: Offline Sonork: 100.1651182 Thanks Meter: 483	no power Welcome to Octoplus Pro JTAG Software version 1.7.6. Started. Reader #0: Alcor Micro USB Smart Card Reader 0 Reader #1: Alcor Micro USB Smart Card Reader 1 Reader #2: Broadcom Corp Contacted SmartCard 0 Please disconnect battery and USB cable. Model Settings: Interface : eMMC Brand : Samsung Model : SM-J110H SRF : C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf Voltage : 1.8V Bus Mode : 1 bit Bus speed : Auto Connecting... Device : Hynix eMMC H4G2b Page size : 512 B Block size : 512 B Block count : 7634944 Size : 3728.00 MB --------------------------------------------------------------- CID Info CID : 90014A4834473262110142E04C5F4353 Manufacturer ID : 0X90 Device/BGA : BGA (Discrete embedded) OEM/Application ID : 0X4A Product name : H4G2b Product revision : 0.1 Product serial number : (hex) 42E04C5F Manufacturing date : 04/2016 --------------------------------------------------------------- CSD Info CSD : D07F01320F5903FFFFFFFFEF8A4040DB CSD structure : CSD version No. 1.2 SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5, 4.51, 5.0, 5.01, 5.1 Data read access time1: 80 ms TRAN speed : 26 MHz READ block length : 512 Bytes WP group enable : YES PERM_WRITE_PROTECT : NO TMP_WRITE_PROTECT : NO --------------------------------------------------------------- EXTCSD Info Revision 1.6 (for MMC v4.5, v4.51) Erase block size : 512 Kbytes Boot1 size : 4096 Kbytes Boot2 size : 4096 Kbytes RPMB size : 4096 Kbytes Partition config : (0x08) 00001000 Boot partition enable : Boot partition 1 (Bus width = 1Bit) Boot ACK : No boot acknowledge sent (default) Boot bus conditions : (0x00) 00000000 Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default) Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default) Boot mode : Use single data rate + backward compatible timings in boot operation (default) RST_n function : (0x00) RST_n signal is temporary disabled (default) Partitioning support : Device supports partitioning features Enhanced attribute : Device can have enhanced technological features in partitions and user data area. Max enhanced data size: 1908736 Kbytes Partitions attribute : 0x0 Part setting completed: 0x0 GP partition 1 size : 0 b GP partition 2 size : 0 b GP partition 3 size : 0 b GP partition 4 size : 0 b Enhanced area size : (0x0) 0 b Enhanced area start : (0x0) 0 b ---------------------------------------------------------------Searching Android build info... Not found --------------------------------------------------------------- Backup EXT_CSD saved to file C:/Program Files/Octoplus Pro JTAG Software/EXT_CSD Backups/H4G2b_20_04_2019_16_03_02.bin. Connect successful. --------------------------------------------------------------- SW: 1.7.6; FW: 1.24. P00: GPT (00000000, 00002000) 4 MB P01: SBOOT (00002000, 00001000) 2048 KB P02: SBOOT2 (00003000, 00001000) 2048 KB P03: wfixnv1 (00004000, 00000800) 1024 KB P04: wfixnv2 (00004800, 00000800) 1024 KB P05: tdfixnv1 (00005000, 00000800) 1024 KB P06: tdfixnv2 (00005800, 00000800) 1024 KB P07: WDSP (00006000, 00002000) 4 MB P08: MODEM (00008000, 00004000) 8 MB P09: MODEM2 (0000C000, 00004000) 8 MB P10: TDDSP (00010000, 00002000) 4 MB P11: FOTA_SIG (00012000, 00000800) 1024 KB P12: wruntimenv1 (00012800, 00000800) 1024 KB P13: wruntimenv2 (00013000, 00000800) 1024 KB P14: tdruntimenv1 (00013800, 00000800) 1024 KB P15: tdruntimenv2 (00014000, 00000800) 1024 KB P16: PARAM (00014800, 00001000) 2048 KB P17: EFS (00015800, 0000A000) 20 MB P18: PRODNV (0001F800, 00002800) 5 MB P19: RESERVED2 (00022000, 00000800) 1024 KB P20: KERNEL (00022800, 00008000) 16 MB P21: RECOVERY (0002A800, 00008000) 16 MB P22: PERSDATA (00032800, 00004800) 9 MB P23: CSC (00037000, 00064000) 200 MB P24: SYSTEM (0009B000, 00203000) 1030 MB P25: HIDDEN (0029E000, 0001D000) 58 MB P26: USERDATA (002BB000, 00486000) 2316 MB Repairing from file "C:/Program Files/Octoplus Pro JTAG Software/firmwareFolder/SAMSUNG_SM-J110H_EMMC.srf". Write data verification is enabled. Switched to boot area partition 1. Writing BOOT1 partition... Done. Switched to boot area partition 2. Writing BOOT2 partition... Done. Switched to user area. Writing GPT partition... Done. Writing SBOOT partition... Done. Writing SBOOT2 partition... Done. Writing wfixnv1 partition... Done. Writing wfixnv2 partition... Done. Writing tdfixnv1 partition... Done. Writing tdfixnv2 partition... Done. Writing WDSP partition... Done. Writing MODEM partition... Done. Writing MODEM2 partition... Done. Writing TDDSP partition... Done. Writing FOTA_SIG partition... Done. Writing wruntimenv1 partition... Done. Writing wruntimenv2 partition... Done. Writing tdruntimenv1 partition... Done. Writing tdruntimenv2 partition... Done. Writing PARAM partition... Done. Writing EFS partition... Done. Writing PRODNV partition... Done. Writing RESERVED2 partition... Done. Writing KERNEL partition... Done. Writing RECOVERY partition... Done. Writing PERSDATA partition... Done. Writing CSC partition... Done. Smart Repair is successfully complete. SW: 1.7.6; FW: 1.24. Disconnected.

04-20-2019, 13:03	#5 (permalink)
alimobile279 No Life Poster Join Date: Mar 2011 Location: Faisalabad Posts: 1,482 Member: 1527968 Status: Offline Sonork: 100.1651182 Thanks Meter: 483	not working no power on.................