Need Sony E5563 eMMC dump [Answered] - GSM-Forum

shaikh_shoeb50 · 11-16-2017, 08:05

i need Sony E5563 emmc dump....

phone was stuck on sony logo before but after flashed phone dead....

now phone connect in device manager as Unknown device....

can anyone upload dump file...

Octopus box · 11-16-2017, 11:43

Hello.

Do You have eMMC pinout for this device? Have You connected it via eMMC? If yes, post here full Software log with devices info and connecting procedure.

shaikh_shoeb50 · 11-16-2017, 16:27

I have connected it via emmc...

this is 1st logs when i emmc connect and read backup TA and etc...

Quote:

Welcome to Medusa Pro Software version 1.4.5.
Started.
Reader #0: Alcor Micro USB Smart Card Reader 0
Reader #1: FT SCR2000 0

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Samsung eMMC R311MB
Page size : 512 B
Block size : 512 B
Block count : 30535680
Size : 14.56 GB
---------------------------------------------------------------
CID Info

CID : 150100523331314D4201DD76F20A828F
Manufacturer ID : 0X15
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X00
Product name : R311MB
Product revision : 0.1
Product serial number : (hex) DD76F20A
Manufacturing date : 08/2015
---------------------------------------------------------------
CSD Info

CSD : D02701320F5903FFF6DBFFEF8E40400D
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.7 (for MMC v5.0, v5.01)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : 01001000
Boot partition enable : Boot partition 1 (Bus width = 1Bit)
Boot ACK : Boot acknowledge sent during boot operation Bit

Boot bus conditions : 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 7626752 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...Ok

Disk/Image size : a3e00000 bytes
Device sector size : 512 bytes
Partition offset : 25247744
Number of sectors : 5229568
Device Manufacturer : alps
Device Platform : mt6752
Build ID : 29.1.B.0.87
Display Build ID : 29.1.B.0.87
Release ID : 5.1
Device Model : E5563
Device Name : Xperia C5 Ultra Dual
Architecture ABI : arm64-v8a
Architecture ABI List : arm64-v8a,armeabi-v7a,armeabi
Build Description : full_arima6752_65_s_l1-user 5.1 2.71.J.0.102_201512120913 1449893757 test-keys

Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/R311MB_14_11_2017_12_45_57.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.4.5; FW: 1.22.
P00: GPT (00000000, 00000400)
P01: ta (00000400, 00001000)
P02: proinfo (00001400, 00001800)
P03: nvram (00002C00, 00002800)
P04: protect1 (00005400, 00005000)
P05: protect2 (0000A400, 00005000)
P06: seccfg (0000F400, 00000400)
P07: lk (0000F800, 00000800)
P08: ltalabel (00010000, 00008000)
P09: fotakernel (00018000, 00014000)
P10: boot (0002C000, 00014000)
P11: secro (00040000, 00003000)
P12: para (00043000, 00000400)
P13: logo (00043400, 00004000)
P14: expdb (00047400, 00005000)
P15: tee1 (0004C400, 00002800)
P16: tee2 (0004EC00, 00002800)
P17: metadata (00051400, 00010000)
P18: gen (00061400, 00000800)
P19: apps_log (00064000, 00004000)
P20: oem (00068000, 0007C000)
P21: cache (000E4000, 00064000)
P22: userdata (00148000, 016CC000)
P23: system (01814000, 004FCC00)
P24: flashinfo (01D10C00, 00008000)
Backuping TA partition...
Opening C:/Program Files/Medusa Pro Software/Backups/R311MB_TA_0x400_0x1000_14_11_2017_12_45_57.bin file...
Reading. Please wait... Done.
Elapsed time 00:00:00
SW: 1.4.5; FW: 1.22.

Analyzing Trim Area (TA)... Ok
TA IMEI: 35219207402319
Lock status: locked
Reading partition GPT to buffer... Done.
Reading partition ta to buffer... Done.
Reading partition proinfo to buffer... Done.
Reading partition nvram to buffer... Done.
Reading partition protect1 to buffer... Done.
Reading partition protect2 to buffer... Done.
Reading partition seccfg to buffer... Done.
Reading partition lk to buffer... Done.
Reading partition ltalabel to buffer... Done.
Reading partition fotakernel to buffer... Done.
Reading partition boot to buffer... Done.
Reading partition secro to buffer... Done.
Reading partition para to buffer... Done.
Reading partition logo to buffer... Done.
Reading partition expdb to buffer... Done.
Reading partition tee1 to buffer... Done.
Reading partition tee2 to buffer... Done.
Reading partition metadata to buffer... Done.
Reading partition gen to buffer... Done.
Reading partition apps_log to buffer... Done.
Reading partition oem to buffer... Done.
Reading partition cache to buffer... Done.
Reading partition flashinfo to buffer... Done.
Reading is finished.
Saved to file C:/Users/Safa/Downloads/Samsung eMMC R311MB_14_11_2017_12_46_31.mpt.
SW: 1.4.5; FW: 1.22.

i have already tried via factory repair button with ftf file...

but it is still connect as unknown device...

Octopus box · 11-16-2017, 16:48

Have You written TA backup after "Factory Repair"? Also, please try to use another firmware for "Factory Repair" and post here full Software log with "Factory Repair" procedure, we will check.

shaikh_shoeb50 · 11-16-2017, 16:48

Factory Repair Logs...

i have write firmware without system and userdata...

Quote:

Selected ftf file: //safa-pc/Users/Safa/Desktop/E5563/E5563_29.2.B.0.122_R2B_India Generic_1298-2220/E5563_29.2.B.0.122_R2B_India Generic_1298-2220.ftf.
File parsing finished.
Writing MBR... Done
Writing primary GPT... Done
Writing secondary GPT... Done
Write data verification is enabled.
Writing. Please wait...
Backuping TA partition... Done.
Writing partition fotakernel... Done.
Writing partition boot... Done.
Writing partition oem... Done.
Writing partition cache... Done.
Writing is finished.
SW: 1.4.8; FW: 1.22.

after factory repair logs...but after flash logs ta area changed?

Quote:

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Connecting...
Device : Samsung eMMC R311MB
Page size : 512 B
Block size : 512 B
Block count : 30535680
Size : 14.56 GB
---------------------------------------------------------------
CID Info

CID : 150100523331314D4201DD76F20A828F
Manufacturer ID : 0X15
Device/BGA : BGA (Discrete embedded)
OEM/Application ID : 0X00
Product name : R311MB
Product revision : 0.1
Product serial number : (hex) DD76F20A
Manufacturing date : 08/2015
---------------------------------------------------------------
CSD Info

CSD : D02701320F5903FFF6DBFFEF8E40400D
CSD structure : CSD version No. 1.2
SPEC version : 4.1, 4.2, 4.3, 4.4, 4.41, 4.5,
4.51, 5.0, 5.01, 5.1
Data read access time1: 15 ms
TRAN speed : 26 MHz
READ block length : 512 Bytes
WP group enable : YES
PERM_WRITE_PROTECT : NO
TMP_WRITE_PROTECT : NO
---------------------------------------------------------------
EXTCSD Info

Revision 1.7 (for MMC v5.0, v5.01)
Erase block size : 512 Kbytes
Boot1 size : 4096 Kbytes
Boot2 size : 4096 Kbytes
RPMB size : 4096 Kbytes

Partition config : 01001000
Boot partition enable : Boot partition 1 (Bus width = 1Bit)
Boot ACK : Boot acknowledge sent during boot operation Bit

Boot bus conditions : 00000000
Boot bus width : x1 (sdr) or x4 (ddr) bus width in boot operation mode (default)
Reset boot bus conditions : Reset bus width to x1, single data rate and backward compatible timings after boot operation (default)
Boot mode : Use single data rate + backward compatible timings in boot operation (default)

RST_n function : (0x00) RST_n signal is temporary disabled (default)

Partitioning support : Device supports partitioning features
Enhanced attribute : Device can have enhanced technological features in partitions and user data area.
Max enhanced data size: 7626752 Kbytes
Partitions attribute : 0x0
Part setting completed: 0x0
GP partition 1 size : 0 b
GP partition 2 size : 0 b
GP partition 3 size : 0 b
GP partition 4 size : 0 b
Enhanced area size : (0x0) 0 b
Enhanced area start : (0x0) 0 b

---------------------------------------------------------------Searching Android build info...
Backup EXT_CSD saved to file C:/Program Files/Medusa Pro Software/EXT_CSD Backups/R311MB_16_11_2017_21_11_53.bin.
Connect successful.
---------------------------------------------------------------
SW: 1.4.8; FW: 1.22.
P00: GPT (00000000, 00028400) 80.5 MB
P01: ta (00028400, 00001000) 2048 KB
P02: proinfo (00029400, 00001800) 3072 KB
P03: nvram (0002AC00, 00002800) 5 MB
P04: protect1 (0002D400, 00005000) 10 MB
P05: protect2 (00032400, 00005000) 10 MB
P06: seccfg (00037400, 00000400) 512 KB
P07: lk (00037800, 00000800) 1024 KB
P08: ltalabel (00038000, 00008000) 16 MB
P09: fotakernel (00040000, 00014000) 40 MB
P10: boot (00054000, 00014000) 40 MB
P11: secro (00068000, 00003000) 6 MB
P12: para (0006B000, 00000400) 512 KB
P13: logo (0006B400, 00004000) 8 MB
P14: expdb (0006F400, 00005000) 10 MB
P15: tee1 (00074400, 00002800) 5 MB
P16: tee2 (00076C00, 00002800) 5 MB
P17: metadata (00079400, 00010000) 32 MB
P18: gen (00089400, 00000800) 1024 KB
P19: apps_log (0008C000, 00004000) 8 MB
P20: oem (00090000, 0007C000) 248 MB
P21: cache (0010C000, 00064000) 200 MB
P22: userdata (00170000, 016CC000) 11.4 GB
P23: system (0183C000, 004FCC00) 2554 MB
P24: flashinfo (01D38C00, 00008000) 16 MB
Backuping TA partition...
Opening C:/Program Files/Medusa Pro Software/Backups/R311MB_TA_0x28400_0x1000_16_11_2017_21_11_53.bin file...
Reading. Please wait... Done.
Elapsed time 00:00:00
SW: 1.4.8; FW: 1.22.

Analyzing Trim Area (TA)... Ok
TA IMEI: 35219207402319
Lock status: locked

Octopus box · 11-16-2017, 17:25

Most likely, boot1 is damaged in your phone. We will try to find boot1 backup for your device and, if will find, we will send You for test.

Medusa Box · 11-17-2017, 09:29

Here are two versions of boot1 for E5563:
https://drive.google.com/open?id=1mu...tQ9c6ZCwCTrg-H,
https://drive.google.com/open?id=17r...d6LCR0qLpPD2Mr.

Try to write at first boot1_v1 and try to power on the phone. If the phone doesn't power on, try to write boot1_v2.

If the phone still doesn't start, try to write your backup "Samsung eMMC R311MB_14_11_2017_12_46_31.mpt", then write boot1_v1/boot1_v2, write the first TA backup and try to boot the phone.

niangrg12 · 05-06-2018, 06:56

pinout for e5363 pleawse

Medusa Box · 05-06-2018, 15:13

Unfortunately, not all necessary pins are present on phone's PCB for ISP connection, so to repair this device, You need to remove eMMC chip from PCB for repairing (programming).

WINDA · 10-18-2018, 08:33

please pinout emmc sony
]

11-16-2017, 08:05	#1 (permalink)
shaikh_shoeb50 No Life Poster Join Date: May 2011 Location: ..:Inside UR Brain:.. Age: 34 Posts: 524 Member: 1586370 Status: Offline Sonork: 100.1618206 Thanks Meter: 154	Need Sony E5563 eMMC dump [Answered] i need Sony E5563 emmc dump.... phone was stuck on sony logo before but after flashed phone dead.... now phone connect in device manager as Unknown device.... can anyone upload dump file... Last edited by Octopus box; 03-28-2018 at 11:21.

11-16-2017, 17:25	#6 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,802 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,406	Most likely, boot1 is damaged in your phone. We will try to find boot1 backup for your device and, if will find, we will send You for test. Last edited by Octopus box; 11-17-2017 at 07:34.

05-06-2018, 06:56	#8 (permalink)
niangrg12 Junior Member Join Date: Apr 2016 Posts: 21 Member: 2555179 Status: Offline Thanks Meter: 7	sony c4 dual pinout for e5363 pleawse

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-16-2017, 11:43	#2 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,802 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,406	Hello. Do You have eMMC pinout for this device? Have You connected it via eMMC? If yes, post here full Software log with devices info and connecting procedure.

11-16-2017, 16:48	#4 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,802 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,406	Have You written TA backup after "Factory Repair"? Also, please try to use another firmware for "Factory Repair" and post here full Software log with "Factory Repair" procedure, we will check.

11-17-2017, 09:29	#7 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 9,360 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks Meter: 3,397	Here are two versions of boot1 for E5563: https://drive.google.com/open?id=1mu...tQ9c6ZCwCTrg-H, https://drive.google.com/open?id=17r...d6LCR0qLpPD2Mr. Try to write at first boot1_v1 and try to power on the phone. If the phone doesn't power on, try to write boot1_v2. If the phone still doesn't start, try to write your backup "Samsung eMMC R311MB_14_11_2017_12_46_31.mpt", then write boot1_v1/boot1_v2, write the first TA backup and try to boot the phone.

05-06-2018, 15:13	#9 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 9,360 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks Meter: 3,397	Unfortunately, not all necessary pins are present on phone's PCB for ISP connection, so to repair this device, You need to remove eMMC chip from PCB for repairing (programming).

10-18-2018, 08:33	#10 (permalink)
WINDA No Life Poster Join Date: Jul 2008 Location: indonesia Posts: 990 Member: 804772 Status: Offline Thanks Meter: 129	please pinout emmc sony ]