LG-H962 HANG ON LOGO RECOVER Done - GSM-Forum

gracy_elec · 10-20-2017, 09:16

SUCCESSFULLY RECOVER HANG ON LOGO (LG-H962)USB

Welcome to Octoplus/Octopus Box LG Software

----------------------------------------------------------------------------------------------------------------------------------------------------
Checking data...OK
Platform: LG Qualcomm
Selected port: COM39
Selected model: H962
Reading info...
Model ID: LG-H962
IMEI: XXXXXXXXXXXXXXX
Android version: 6.0
Battery level: 11%
SW Version: H96220c
Mode: Emergency
Initializing flash...OK
SW version: LGH962AT-00-V20e-TWN-XX-SEP-19-2016+0
Android version: 6.0
LAF Version: 1.1
Product ID: YE02S151215005385
IMEI: 355213-07-012993-7
Target operator: GLOBAL
Hardware: rev_10
----------------------------------------------------------------------------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
----------------------------------------------------------------------------------------------------------------------------------------------------
Opening "H96230b_00_0621.oct"...OK
Setting options...OK
Reading partitions...OK
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing PrimaryGPT...OK
Writing modem...OK
Writing pmic...OK
Writing sbl1...OK
Writing tz...OK
Writing sdi...OK
Writing hyp...OK
Writing rpm...OK
Writing aboot...OK
Writing sbl1bak...OK
Writing pmicbak...OK
Writing hypbak...OK
Writing tzbak...OK
Writing rpmbak...OK
Writing abootbak...OK
Writing sdibak...OK
Writing persist...OK
Writing sec...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing raw_resources...OK
Writing raw_resourcesbak...OK
Writing factory...OK
Writing system...OK
Writing cust...OK
Writing BackupGPT...OK
Reading partitions...OK
Formating RCT...OK
Formating MPT...OK
Finalizing...OK
Writing firmware done!

THANKS OCTOPULS-BOX TEAM

DEASEAN · 02-04-2018, 16:16

instuctions on how to do this plz.

Octopus box · 02-05-2018, 06:46

Hello.

Please read Software manual ("Cable & Options" tab in Software) on how to write firmware.

10-20-2017, 09:16	#1 (permalink)
gracy_elec No Life Poster Join Date: Feb 2005 Location: GSM WORLD Posts: 2,079 Member: 118520 Status: Offline Thanks Meter: 3,551	LG-H962 HANG ON LOGO RECOVER Done SUCCESSFULLY RECOVER HANG ON LOGO (LG-H962)USB Welcome to Octoplus/Octopus Box LG Software ---------------------------------------------------------------------------------------------------------------------------------------------------- Checking data...OK Platform: LG Qualcomm Selected port: COM39 Selected model: H962 Reading info... Model ID: LG-H962 IMEI: XXXXXXXXXXXXXXX Android version: 6.0 Battery level: 11% SW Version: H96220c Mode: Emergency Initializing flash...OK SW version: LGH962AT-00-V20e-TWN-XX-SEP-19-2016+0 Android version: 6.0 LAF Version: 1.1 Product ID: YE02S151215005385 IMEI: 355213-07-012993-7 Target operator: GLOBAL Hardware: rev_10 ---------------------------------------------------------------------------------------------------------------------------------------------------- Writing phone firmware without real necessity is at your own risk. Downgrade may lead to phone damage! Please, make sure the phone's battery is fully charged. Disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Qualcomm-based devices). You should not run any other programs or attach new devices to your computer during the flashing! ---------------------------------------------------------------------------------------------------------------------------------------------------- Opening "H96230b_00_0621.oct"...OK Setting options...OK Reading partitions...OK Formating USERDATA...OK Formating ENCRYPT...OK Sending signature...OK Writing PrimaryGPT...OK Writing modem...OK Writing pmic...OK Writing sbl1...OK Writing tz...OK Writing sdi...OK Writing hyp...OK Writing rpm...OK Writing aboot...OK Writing sbl1bak...OK Writing pmicbak...OK Writing hypbak...OK Writing tzbak...OK Writing rpmbak...OK Writing abootbak...OK Writing sdibak...OK Writing persist...OK Writing sec...OK Writing laf...OK Writing boot...OK Writing recovery...OK Writing raw_resources...OK Writing raw_resourcesbak...OK Writing factory...OK Writing system...OK Writing cust...OK Writing BackupGPT...OK Reading partitions...OK Formating RCT...OK Formating MPT...OK Finalizing...OK Writing firmware done! THANKS OCTOPULS-BOX TEAM

02-04-2018, 16:16	#2 (permalink)
DEASEAN Junior Member Join Date: Jun 2016 Location: Pluto Posts: 3 Member: 2584113 Status: Offline Thanks Meter: 0	instuctions on how to do this plz.

02-05-2018, 06:46	#3 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,848 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,413	Hello. Please read Software manual ("Cable & Options" tab in Software) on how to write firmware.