Error: 0108 in Terminator 1.8 - GSM-Forum

**nonu_don** · 03-29-2003, 06:44

hi, can anyone tell me what is this error for,, ie error 0108 in terminator 1.2 to terminator 2.0

actually i am trying to read codes for my t200 and after 3-4 times of blue bar going to 50% and resets,, this error comes.

plz help me
Naman

**nonu_don** · 03-29-2003, 06:57

weel i must tell that the phone i used (t200) was an unlocked one.

may be this is the reason

Naman

Raklm · 03-29-2003, 11:24

I think not

I readed T200 unlocked and gived me corect codes
I locked back with NCK and unlocked again

BR
Rak|m

*MaTeOoSh* · 03-29-2003, 13:48

error 0108 appears when terminator can't bypass boot authority (more precisely - not received expected byte sequence). Just remove battery in phone, put it in and try again - I encountered this problem many times (in fact not in T200 - most in T65) but all solved after some tries ...

Good Luck

**nonu_don** · 03-29-2003, 15:27

thanx,,,
will try it some more time,,,,,
but now error 0101, think pic has fried, but detects dongle and dct4 also works good... dont know whats wrong now

Naman

Tygiel · 04-02-2003, 10:51

I had error 0108 few times and always i clean phone conector and then work ok.

Regards

**nonu_don** · 04-02-2003, 11:45

thnx for replying,
will try it when i get a phone to work on..
Naman

**nonu_don** · 04-02-2003, 16:27

no, pin cleaning didnt worked out.

well i got 1 thing
the pins at phone connector that is from 1 to 12, there is continuity in pin no. 2 to pin no. 6 when i connect the dongle to lpt, otherwise no continuity. that is Rx is connected to GND when i connect dongle to lpt port, which is not practicle. i think. this might be the problem, but dont know why is it there.

checked several times
plz help

Naman

03-29-2003, 06:44	#1 (permalink)
nonu_don Product Manager Join Date: Feb 2003 Location: ..::India::.. Age: 29 Posts: 3,806 Member: 22538 Status: Offline Sonork: 100.67180 Thanks: 153 Thanked 2,242 Times in 444 Posts	Error: 0108 in Terminator 1.8 hi, can anyone tell me what is this error for,, ie error 0108 in terminator 1.2 to terminator 2.0 actually i am trying to read codes for my t200 and after 3-4 times of blue bar going to 50% and resets,, this error comes. plz help me Naman

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
any 1 tell me about how can use new obtion unlock type(1,2,,3,4,5,6,7,8) in v 1.8	MSCOMMUNICATION	YESSIM	1	09-07-2008 10:36
div usb for terminator 1.8 free	JOFF	Sony Ericsson	2	02-05-2004 22:42
for all people who get Error 0108 with Terminator	CyberGSM	Sony Ericsson	7	04-21-2003 09:01
Terminator 1.8 sheme&HEX free	eddi®	Old Ericsson Phones & Sony Phones	3	02-14-2003 21:49
Terminator 1.8 / DIV 3.8 - DOWNLOAD	VsH-GsM	Sony Ericsson	28	01-03-2003 16:51

03-29-2003, 06:57	#2 (permalink)
nonu_don Product Manager Join Date: Feb 2003 Location: ..::India::.. Age: 29 Posts: 3,806 Member: 22538 Status: Offline Sonork: 100.67180 Thanks: 153 Thanked 2,242 Times in 444 Posts	weel i must tell that the phone i used (t200) was an unlocked one. may be this is the reason Naman

03-29-2003, 11:24	#3 (permalink)
Raklm No Life Poster Join Date: Aug 2001 Location: Roma Age: 38 Posts: 4,203 Member: 5926 Status: Offline Thanks: 135 Thanked 235 Times in 159 Posts	I think not I readed T200 unlocked and gived me corect codes I locked back with NCK and unlocked again BR Rak\|m

03-29-2003, 13:48	#4 (permalink)
MaTeOoSh No Life Poster Join Date: Dec 2000 Location: gsmdoctor.pl Age: 37 Posts: 1,324 Member: 2755 Status: Online Thanks: 3 Thanked 42 Times in 32 Posts	error 0108 appears when terminator can't bypass boot authority (more precisely - not received expected byte sequence). Just remove battery in phone, put it in and try again - I encountered this problem many times (in fact not in T200 - most in T65) but all solved after some tries ... Good Luck

03-29-2003, 15:27	#5 (permalink)
nonu_don Product Manager Join Date: Feb 2003 Location: ..::India::.. Age: 29 Posts: 3,806 Member: 22538 Status: Offline Sonork: 100.67180 Thanks: 153 Thanked 2,242 Times in 444 Posts	thanx,,, will try it some more time,,,,, but now error 0101, think pic has fried, but detects dongle and dct4 also works good... dont know whats wrong now Naman

04-02-2003, 10:51	#6 (permalink)
Tygiel Freak Poster Join Date: Feb 2002 Location: Poland Age: 31 Posts: 181 Member: 9565 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	I had error 0108 few times and always i clean phone conector and then work ok. Regards

04-02-2003, 11:45	#7 (permalink)
nonu_don Product Manager Join Date: Feb 2003 Location: ..::India::.. Age: 29 Posts: 3,806 Member: 22538 Status: Offline Sonork: 100.67180 Thanks: 153 Thanked 2,242 Times in 444 Posts	thnx for replying, will try it when i get a phone to work on.. Naman

04-02-2003, 16:27	#8 (permalink)
nonu_don Product Manager Join Date: Feb 2003 Location: ..::India::.. Age: 29 Posts: 3,806 Member: 22538 Status: Offline Sonork: 100.67180 Thanks: 153 Thanked 2,242 Times in 444 Posts	no, pin cleaning didnt worked out. well i got 1 thing the pins at phone connector that is from 1 to 12, there is continuity in pin no. 2 to pin no. 6 when i connect the dongle to lpt, otherwise no continuity. that is Rx is connected to GND when i connect dongle to lpt port, which is not practicle. i think. this might be the problem, but dont know why is it there. checked several times plz help Naman