I have getting error 3608 in DIV while flashing the ARM - GSM-Forum

kingofhearts · 04-09-2003, 09:31

HI,

I have getting error 3608 in DIV while flashing the ARM section. It can flash the AVR successfully in T-68 but i cant flash the arm. What can i do how solve this problem.

Bigbrothers2000 · 09-02-2003, 12:18

I have the same problem but i don't know how to fix it ??

best regards

fontelense · 09-02-2003, 22:31

Maybe it's bad ARM chip, try reflow it.
A few days ago, something similar happened to me, a T39 refused to flash ARM, always error 3610, 3608, etc. I left it for a few hours, tried flashing again and it worked. Very strange...

Best regards

Bigbrothers2000 · 09-03-2003, 08:09

Ok i found it dont use the wire from pin 9 and 11
because pin 9 and 11 is shortcut and there is a wire ,,
cut the wire leave 9 and 11 shortcut and it will work

best regards

gorbulas · 09-10-2003, 16:08

???

Which wire?

There is no shortcut between 9 and 11

9 and 11 at the SE Connector or at the DB25 connector?

I have the same problem, writing AVR and GDFS is no Problem, but writing ARM i always get 3608.

I tried this with DIV 7.1 and DIV 8.2 and with T68 and T610 always the same problem!

Can anybody help me please!

Bigbrothers2000 · 09-10-2003, 21:02

Then connect 9 and 11 at the SE Connector

best regards

gsmhk · 09-11-2003, 04:22

you made mistake about connection between 4066 and phone

phone <-> 4066
5 <-> 11
6 <-> 2
7 <-> 8
8 <-> 3

check connection between PIC and 4066 also

good luck.

gorbulas · 09-11-2003, 08:44

@ Bigbrothers2000

My mistake, there is a shortcut between 9 and 11, i have found a schema with wrong pin numbers (1 is 11 and 11 is 1).

So, now i have my shortcut with the wire. I cut the wire and now everything is fine, i can N O T write anything!

This is not the Problem, any other idea?

Thanks

gorbulas · 09-11-2003, 12:12

All done!

GSMhk was right. There was a problem wit the connmection between the 4066 and the PIC16F8. Works fine now.

msa · 09-15-2003, 14:39

@gorbulas

Please can you explain what you had to do for it to work as I am having same error 360A message when trying to flash ARm file.
Thanks

msa

crusher · 09-15-2003, 17:14

forget it

I always get 3608 when flashing with factory terminator and my 8.3 cracked

it is somehow related to connection and voltage levels. investigating now, maybe in 8.4 we'll fix it to let it work with most of your computers

epic · 09-16-2003, 14:06

Is there DIV 8.3 already???? where can DL it??? thanks..

BR,
Epic

gorbulas · 09-17-2003, 15:24

@ msa

One pin of the 4066 was not soldered correctly to the PCB.

Try to meassure the connection between the 4066 and the PIC 16F8.

@ crusher

it has nothing to do with the speed of the computer or the voltage levels. It is just a problem with the logic levels of bad or wrong soldered PCB´s!

Best regards

CyberKareca · 10-07-2003, 12:06

Had same problem and solved it by re-soldering 4066 IC.

gorbulas · 10-07-2003, 15:04

as i said

If you have this error, first check your wire´s, if they are correct, resolder your IC´s on the PCB.

The IC´s are SMD type, so be sure you have good skill with your soldering iron.

1st soldering lesson, the side that is hot, is front

04-09-2003, 09:31	#1 (permalink)
kingofhearts No Life Poster Join Date: Jan 2002 Location: Karachi, Pakistan Age: 30 Posts: 872 Member: 8710 Status: Offline Sonork: 1576303 Thanks: 8 Thanked 197 Times in 37 Posts	I have getting error 3608 in DIV while flashing the ARM HI, I have getting error 3608 in DIV while flashing the ARM section. It can flash the AVR successfully in T-68 but i cant flash the arm. What can i do how solve this problem.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
Error in 7610 while flashing ....	kit_kit	UFS2 + UFS3-Tornadoflasher	3	07-10-2008 10:35
What is Error 13.0000 in griffin while flashing	bcnboy	Griffin	0	08-16-2004 18:35
Error 201 error 301 in DIV Plz HELP!!!!	Shubhanshu~	DIV	2	07-09-2004 21:37
Error Codes In Div	mumien	Sony Ericsson	1	12-30-2003 23:33
I have getting error 3608 with DIV????	ecsike	Sony Ericsson	2	09-12-2003 12:14

09-02-2003, 12:18	#2 (permalink)
Bigbrothers2000 No Life Poster Join Date: Sep 1999 Location: Europe Age: 41 Posts: 1,364 Member: 487 Status: Offline Thanks: 14 Thanked 61 Times in 39 Posts	I have the same problem but i don't know how to fix it ?? best regards

09-02-2003, 22:31	#3 (permalink)
fontelense No Life Poster Join Date: Sep 2001 Location: Portugal Age: 39 Posts: 598 Member: 6358 Status: Offline Thanks: 0 Thanked 9 Times in 7 Posts	Maybe it's bad ARM chip, try reflow it. A few days ago, something similar happened to me, a T39 refused to flash ARM, always error 3610, 3608, etc. I left it for a few hours, tried flashing again and it worked. Very strange... Best regards

09-03-2003, 08:09	#4 (permalink)
Bigbrothers2000 No Life Poster Join Date: Sep 1999 Location: Europe Age: 41 Posts: 1,364 Member: 487 Status: Offline Thanks: 14 Thanked 61 Times in 39 Posts	Ok i found it dont use the wire from pin 9 and 11 because pin 9 and 11 is shortcut and there is a wire ,, cut the wire leave 9 and 11 shortcut and it will work best regards

09-10-2003, 16:08	#5 (permalink)
gorbulas No Life Poster Join Date: Sep 2003 Location: somewhere nice and warm Age: 50 Posts: 728 Member: 38800 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	??? Which wire? There is no shortcut between 9 and 11 9 and 11 at the SE Connector or at the DB25 connector? I have the same problem, writing AVR and GDFS is no Problem, but writing ARM i always get 3608. I tried this with DIV 7.1 and DIV 8.2 and with T68 and T610 always the same problem! Can anybody help me please!

09-10-2003, 21:02	#6 (permalink)
Bigbrothers2000 No Life Poster Join Date: Sep 1999 Location: Europe Age: 41 Posts: 1,364 Member: 487 Status: Offline Thanks: 14 Thanked 61 Times in 39 Posts	Then connect 9 and 11 at the SE Connector best regards

09-11-2003, 04:22	#7 (permalink)
gsmhk Insane Poster Join Date: Jan 2000 Posts: 61 Member: 874 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	you made mistake about connection between 4066 and phone phone <-> 4066 5 <-> 11 6 <-> 2 7 <-> 8 8 <-> 3 check connection between PIC and 4066 also good luck.

09-11-2003, 08:44	#8 (permalink)
gorbulas No Life Poster Join Date: Sep 2003 Location: somewhere nice and warm Age: 50 Posts: 728 Member: 38800 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	@ Bigbrothers2000 My mistake, there is a shortcut between 9 and 11, i have found a schema with wrong pin numbers (1 is 11 and 11 is 1). So, now i have my shortcut with the wire. I cut the wire and now everything is fine, i can N O T write anything! This is not the Problem, any other idea? Thanks

09-11-2003, 12:12	#9 (permalink)
gorbulas No Life Poster Join Date: Sep 2003 Location: somewhere nice and warm Age: 50 Posts: 728 Member: 38800 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	All done! GSMhk was right. There was a problem wit the connmection between the 4066 and the PIC16F8. Works fine now.

09-15-2003, 14:39	#10 (permalink)
msa No Life Poster Join Date: Nov 2002 Posts: 762 Member: 17424 Status: Offline Thanks: 34 Thanked 10 Times in 8 Posts	@gorbulas Please can you explain what you had to do for it to work as I am having same error 360A message when trying to flash ARm file. Thanks msa

09-15-2003, 17:14	#11 (permalink)
crusher No Life Poster Join Date: Dec 2001 Location: [winscard.SCardTransmit] Age: 93 Posts: 1,842 Member: 8023 Status: Offline Thanks: 11 Thanked 13 Times in 10 Posts	forget it I always get 3608 when flashing with factory terminator and my 8.3 cracked it is somehow related to connection and voltage levels. investigating now, maybe in 8.4 we'll fix it to let it work with most of your computers

09-16-2003, 14:06	#12 (permalink)
epic No Life Poster Join Date: Apr 2002 Location: Tutuban Age: 57 Posts: 1,359 Member: 10635 Status: Offline Thanks: 2 Thanked 10 Times in 10 Posts	Is there DIV 8.3 already???? where can DL it??? thanks.. BR, Epic

09-17-2003, 15:24	#13 (permalink)
gorbulas No Life Poster Join Date: Sep 2003 Location: somewhere nice and warm Age: 50 Posts: 728 Member: 38800 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	@ msa One pin of the 4066 was not soldered correctly to the PCB. Try to meassure the connection between the 4066 and the PIC 16F8. @ crusher it has nothing to do with the speed of the computer or the voltage levels. It is just a problem with the logic levels of bad or wrong soldered PCB´s! Best regards

10-07-2003, 12:06	#14 (permalink)
CyberKareca No Life Poster Join Date: Mar 2001 Location: Porto - Portugal Posts: 857 Member: 3769 Status: Offline Thanks: 13 Thanked 52 Times in 17 Posts	Had same problem and solved it by re-soldering 4066 IC.

10-07-2003, 15:04	#15 (permalink)
gorbulas No Life Poster Join Date: Sep 2003 Location: somewhere nice and warm Age: 50 Posts: 728 Member: 38800 Status: Offline Thanks: 0 Thanked 1 Time in 1 Post	as i said If you have this error, first check your wire´s, if they are correct, resolder your IC´s on the PCB. The IC´s are SMD type, so be sure you have good skill with your soldering iron. 1st soldering lesson, the side that is hot, is front