k610 dead???? - GSM-Forum

ahmad yousif · 12-17-2008, 19:16

hi 2 all.....i have k610 dead with these error v0.915016/UNI
CARD SERIAL: 00068085
Loaded 51 flash descriptors
SIGNED MODE (USING SERVER).
ALTERNATIVE SECURITY BYPASS ENABLED.
Open COM port OK
ChipID:9900,EMP protocol:0301
Speed:921600
Can't load ID loader !
Elapsed: 4 secs.
.....plz what that mean? no water inside only its heated

sniper007 · 12-17-2008, 19:28

flash the phone with main and FS, select signed mode and complete phone after flash.

ahmad yousif · 12-20-2008, 17:49

any solution,,,,by the way its not software problem,,,i tried all solution... so any idea

martyn911 · 12-22-2008, 13:49

Try reflash your phone with settings:
*signed mode(use server);
*complete phone after flash;
Phone maybe alive,if no...maybe damage flash chip-need to change...

Regards

ahmad yousif · 12-22-2008, 14:13

Quote:

Originally Posted by martyn911

Try reflash your phone with settings:
*signed mode(use server);
*complete phone after flash;
Phone maybe alive,if no...maybe damage flash chip-need to change...

Regards

u say right 100%100...its flash chip but its protected with (glue)

martyn911 · 12-22-2008, 15:33

For remove this glue,you need carefully heating neer flash chip 200-210C and clean this glue...

regards

12-17-2008, 19:16	#1 (permalink)
ahmad yousif No Life Poster Join Date: May 2008 Location: amman Posts: 935 Member: 764174 Status: Offline Thanks Meter: 259	k610 dead???? hi 2 all.....i have k610 dead with these error v0.915016/UNI CARD SERIAL: 00068085 Loaded 51 flash descriptors SIGNED MODE (USING SERVER). ALTERNATIVE SECURITY BYPASS ENABLED. Open COM port OK ChipID:9900,EMP protocol:0301 Speed:921600 Can't load ID loader ! Elapsed: 4 secs. .....plz what that mean? no water inside only its heated

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
k610 dead after unlock with setool	rose4u86	SETool2	27	10-15-2009 08:09
SE K610 dead????	Remax	MT-BOX	4	02-10-2007 19:45
k610 dead after master reset. .	harish35200	Cruiser Suite	7	01-19-2007 07:49
k610 dead finalize error	VIZER	Cruiser Suite	15	01-15-2007 20:21
k800 3 and 1 k610 dead phones ?????	club gsm	Sony Ericsson	4	08-22-2006 11:27

12-17-2008, 19:28	#2 (permalink)
sniper007 No Life Poster Join Date: Mar 2008 Location: London Posts: 1,307 Member: 722656 Status: Offline Sonork: 100.1584918 Thanks Meter: 294	flash the phone with main and FS, select signed mode and complete phone after flash.

12-20-2008, 17:49	#3 (permalink)
ahmad yousif No Life Poster Join Date: May 2008 Location: amman Posts: 935 Member: 764174 Status: Offline Thanks Meter: 259	any solution,,,,by the way its not software problem,,,i tried all solution... so any idea

12-22-2008, 13:49	#4 (permalink)
martyn911 Freak Poster Join Date: Mar 2005 Location: Ukraine,Kiev Age: 41 Posts: 422 Member: 130762 Status: Offline Sonork: @martyn911 Thanks Meter: 127	Try reflash your phone with settings: signed mode(use server); complete phone after flash; Phone maybe alive,if no...maybe damage flash chip-need to change... Regards

12-22-2008, 15:33	#6 (permalink)
martyn911 Freak Poster Join Date: Mar 2005 Location: Ukraine,Kiev Age: 41 Posts: 422 Member: 130762 Status: Offline Sonork: @martyn911 Thanks Meter: 127	For remove this glue,you need carefully heating neer flash chip 200-210C and clean this glue... regards