T610 Keypad Not Working After Flash With R6c - GSM-Forum

yousha · 11-24-2004, 16:04

I have t610 which was restarting itself before i flashed it with R6C VERSION NOW the problem is when i m making a outgoing call it connects properly but i m unable to use keypad after it than i have to take the battery out

n when i flash it with the version like R1A081 OR R1L it again restart itseft

Crumarix1 · 11-25-2004, 07:57

did you flash bot file : arm and avr , becouse MUST be same RXXX

NeXuSGTS · 11-25-2004, 08:36

flash it with R1L013 MCU+MODEM.
Phone will be ok

Regards,
NeXuSGTS

Aeron2 · 11-25-2004, 15:33

Yes that is right u must flash the two files with the icoresponding files.

yousha · 11-26-2004, 08:15

hey guys of course i have flashed it with all versions and with the corect paires

magnet · 03-11-2005, 14:12

did u solve your problem

magnet · 03-11-2005, 14:31

i too have same problem.

not solved by R1L013 MCU+MODEM.

what to do?

thanks in adv

magnet · 03-12-2005, 09:41

no solution for this??????

need a helping hand

phonebooth304 · 03-12-2005, 10:37

Quote:

Originally Posted by magnet

no solution for this??????

need a helping hand

A new set off buttons or check they are properly in place

jepor · 03-19-2005, 16:51

Quote:

Originally Posted by magnet

no solution for this??????

need a helping hand

i have same problem with this, but i tried use SE Fighter. The 1st: u must backup GDFS from phone with READ GDFS. 2nd: u must make SECURITY ZONE I. 3rd: upload file t610_secondary_GDFS.mdc with use WRITE GDFS. 4th: upload t610_primary_GDFS_no_change_to_calibration.mdc to GDFS. 5th: upload file that u made at number 2 (2nd) to GDFS and Finalize. 6th: flash t610 firmware (the good idea with v.R1A081) step by step (1st. AVR; 2nd.AMR). 7th: take out the battery and start u'r phone will be OK!!!!

if not ok...

u just flash with another version (i think the high version).

11-24-2004, 16:04	#1 (permalink)
yousha No Life Poster Join Date: Nov 2002 Age: 43 Posts: 1,502 Member: 17689 Status: Offline Sonork: 100.72392 Thanks Meter: 737	T610 Keypad Not Working After Flash With R6c I have t610 which was restarting itself before i flashed it with R6C VERSION NOW the problem is when i m making a outgoing call it connects properly but i m unable to use keypad after it than i have to take the battery out n when i flash it with the version like R1A081 OR R1L it again restart itseft

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
V3 Keypad not working after Flash ......... Plz help Mr.TinkerTrain .....	kashi4gul	Smart-Clip	6	02-13-2008 07:45
bluetooth not working after flashing t610	krishn	Sony Ericsson	3	07-09-2004 06:32
t610 keypad not working - help	jasko	Sony Ericsson Hardware Repair	1	03-18-2004 21:02
Nokia 3310 Key 1 not work after flashing with rolis	david69	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	04-27-2003 07:49
C25 does not work after flash with 5108	c25_f51	x1x to x45/x50	0	05-16-2000 16:05

11-25-2004, 07:57	#2 (permalink)
Crumarix1 No Life Poster Join Date: Sep 2004 Location: in AXE control room Age: 54 Posts: 954 Member: 84300 Status: Offline Thanks Meter: 74	did you flash bot file : arm and avr , becouse MUST be same RXXX

11-25-2004, 08:36	#3 (permalink)
NeXuSGTS Freak Poster Join Date: Nov 2003 Location: The upper limit Age: 40 Posts: 352 Member: 44552 Status: Offline Thanks Meter: 3	flash it with R1L013 MCU+MODEM. Phone will be ok Regards, NeXuSGTS

11-25-2004, 15:33	#4 (permalink)
Aeron2 Junior Member Join Date: Nov 2004 Age: 53 Posts: 2 Member: 93571 Status: Offline Thanks Meter: 0	Yes that is right u must flash the two files with the icoresponding files.

11-26-2004, 08:15	#5 (permalink)
yousha No Life Poster Join Date: Nov 2002 Age: 43 Posts: 1,502 Member: 17689 Status: Offline Sonork: 100.72392 Thanks Meter: 737	hey guys of course i have flashed it with all versions and with the corect paires

03-11-2005, 14:12	#6 (permalink)
magnet No Life Poster Join Date: Nov 2002 Location: cellworld Age: 47 Posts: 731 Member: 17907 Status: Offline Thanks Meter: 42	did u solve your problem

03-11-2005, 14:31	#7 (permalink)
magnet No Life Poster Join Date: Nov 2002 Location: cellworld Age: 47 Posts: 731 Member: 17907 Status: Offline Thanks Meter: 42	i too have same problem. not solved by R1L013 MCU+MODEM. what to do? thanks in adv

03-12-2005, 09:41	#8 (permalink)
magnet No Life Poster Join Date: Nov 2002 Location: cellworld Age: 47 Posts: 731 Member: 17907 Status: Offline Thanks Meter: 42	no solution for this?????? need a helping hand