Enable Diag Port...Failed - GSM-Forum

mijanur_017 · 08-22-2019, 14:26

Operation : Enable Diag
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM23)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1600500 [8917] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8917]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8917, eMMC, 16 GB
LU Count : 1 [0x01D5A000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Redmi Note 5A [msm8937] [ugglite]
Software : N2G47H, V9.5.4.0.NDFMIFA [Tue Apr 10 22:23:49 WIB 2018]
Android Ver. : 7.1.2
Patch Level : 2018-03-01
Enable Diag Port...Failed
Operation Failed.
QcFire Ver. 4.6

**U.M.T** · 08-22-2019, 15:30

Use Enable Diag from Xiaomi Special Tab.

Br,
UMT

nctesting2018 · 08-23-2019, 06:57

*#*#717717*#*# if this cant then use this

adb shell
setprop sys.usb.config diag,adb

08-22-2019, 14:26	#1 (permalink)
mijanur_017 Freak Poster Join Date: Aug 2009 Location: Bangladesh Posts: 392 Member: 1087456 Status: Offline Thanks Meter: 39	Enable Diag Port...Failed Operation : Enable Diag Checking for existing devices...Found Port : Qualcomm HS-USB QDLoader 9008 (COM23) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.7 Opening Port...OK Init Handshake Sequence...OK Hardware ID : E1600500 [8917] 00000000 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8917]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8917, eMMC, 16 GB LU Count : 1 [0x01D5A000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Redmi Note 5A [msm8937] [ugglite] Software : N2G47H, V9.5.4.0.NDFMIFA [Tue Apr 10 22:23:49 WIB 2018] Android Ver. : 7.1.2 Patch Level : 2018-03-01 Enable Diag Port...Failed Operation Failed. QcFire Ver. 4.6

08-22-2019, 15:30	#2 (permalink)
U.M.T Product Manager Join Date: Sep 2015 Location: Inside UMT Posts: 9,405 Member: 2465108 Status: Offline Sonork: No More Used Thanks Meter: 13,432	Use Enable Diag from Xiaomi Special Tab. Br, UMT

08-23-2019, 06:57	#3 (permalink)
nctesting2018 Insane Poster Join Date: Oct 2018 Location: SINGAPORE Posts: 71 Member: 2870718 Status: Offline Thanks Meter: 34	##717717## if this cant then use this adb shell setprop sys.usb.config diag,adb