INFOCUS M370i DEAD AFTER FS FORMAT - GSM-Forum

lalit bisht · 05-01-2018, 12:23

PHONE WAS RESTARTING..
I FORMAT WITH UMT QC FIRE V2.1..FORMAT SUCCESSFUL

BUT NOT POWERING ON??

BATTERY OK

STILL IN EDL MODE..NOT EXITING EDL MODE

HELP ME PLEASE..HERE IS LOG-

Operation : Format FS
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000000
OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E
Initializing Protocol...OK
Using Auto Loader Selection [2]
Preparing Firehose Loader...Done
Sending Loader [8909_012.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 8 GB
LU Count : 1 [0x00E90000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : FIH M370 [msm8909]
Software : 00WW_1_120, 00WW_1_120 [Mon Nov 30 17:40:02 CST 2015]
Android Ver. : 5.1.1
Patch Level : 2015-12-01
Preparing Data...Done
Formatting Userdata...Done
Finalizing...Done
Operation Finished.

Deni's · 05-01-2018, 13:17

Quote:

Originally Posted by lalit bisht

PHONE WAS RESTARTING..
I FORMAT WITH UMT QC FIRE V2.1..FORMAT SUCCESSFUL

BUT NOT POWERING ON??

BATTERY OK

STILL IN EDL MODE..NOT EXITING EDL MODE

HELP ME PLEASE..HERE IS LOG-

Operation : Format FS
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000000
OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E
Initializing Protocol...OK
Using Auto Loader Selection [2]
Preparing Firehose Loader...Done
Sending Loader [8909_012.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 8 GB
LU Count : 1 [0x00E90000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : FIH M370 [msm8909]
Software : 00WW_1_120, 00WW_1_120 [Mon Nov 30 17:40:02 CST 2015]
Android Ver. : 5.1.1
Patch Level : 2015-12-01
Preparing Data...Done
Formatting Userdata...Done
Finalizing...Done
Operation Finished.

press long time power on till device reboot if possible remove batre

lalit bisht · 05-01-2018, 14:34

Kept pressed for quite long time..did not get on bro???

**U.M.T** · 05-01-2018, 18:36

In such case, you need to flash factory firmware.

Br,
UMT

lalit bisht · 05-02-2018, 14:03

For factory flash write..phone should be power on?
It is still in edl mode..?

Help me if someone has this phone firmware read via umt.thanks

**U.M.T** · 05-02-2018, 16:14

Writing factory firmware will surely fix this phone.

Br,
UMT

h4in · 07-14-2018, 07:31

can u pl give me test point for hard brick handset???

05-01-2018, 12:23	#1 (permalink)
lalit bisht Freak Poster Join Date: Nov 2012 Age: 51 Posts: 483 Member: 1835756 Status: Offline Thanks Meter: 719	INFOCUS M370i DEAD AFTER FS FORMAT PHONE WAS RESTARTING.. I FORMAT WITH UMT QC FIRE V2.1..FORMAT SUCCESSFUL BUT NOT POWERING ON?? BATTERY OK STILL IN EDL MODE..NOT EXITING EDL MODE HELP ME PLEASE..HERE IS LOG- Operation : Format FS Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM4) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1009600 [8909] 00000000 OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E Initializing Protocol...OK Using Auto Loader Selection [2] Preparing Firehose Loader...Done Sending Loader [8909_012.ufl]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8909, eMMC, 8 GB LU Count : 1 [0x00E90000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : FIH M370 [msm8909] Software : 00WW_1_120, 00WW_1_120 [Mon Nov 30 17:40:02 CST 2015] Android Ver. : 5.1.1 Patch Level : 2015-12-01 Preparing Data...Done Formatting Userdata...Done Finalizing...Done Operation Finished.

05-01-2018, 14:34	#3 (permalink)
lalit bisht Freak Poster Join Date: Nov 2012 Age: 51 Posts: 483 Member: 1835756 Status: Offline Thanks Meter: 719	Kept pressed for quite long time..did not get on bro???

05-01-2018, 18:36	#4 (permalink)
U.M.T Product Manager Join Date: Sep 2015 Location: Inside UMT Posts: 9,405 Member: 2465108 Status: Offline Sonork: No More Used Thanks Meter: 13,432	In such case, you need to flash factory firmware. Br, UMT

05-02-2018, 14:03	#5 (permalink)
lalit bisht Freak Poster Join Date: Nov 2012 Age: 51 Posts: 483 Member: 1835756 Status: Offline Thanks Meter: 719	For factory flash write..phone should be power on? It is still in edl mode..? Help me if someone has this phone firmware read via umt.thanks

05-02-2018, 16:14	#6 (permalink)
U.M.T Product Manager Join Date: Sep 2015 Location: Inside UMT Posts: 9,405 Member: 2465108 Status: Offline Sonork: No More Used Thanks Meter: 13,432	Writing factory firmware will surely fix this phone. Br, UMT

07-14-2018, 07:31	#7 (permalink)
h4in Freak Poster Join Date: Mar 2008 Location: MX-KEY is the BEST NOKIA TOOL Posts: 154 Member: 716661 Status: Offline Thanks Meter: 19	can u pl give me test point for hard brick handset???