★★★ Post Here All Successfully Repaired Phones by Ultimate Multi Tool ★★★ - Page 451 - GSM-Forum

mickeybrown026 · 04-26-2019, 17:17

Operation : Read Firmware
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM612)
Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000400
OPK_DATA : BA512444EBFE66557163424226D37E971BFEF7EEE7AE4D70F7 07FA432EF0B039
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8909_038]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 8 GB
LU Count : 1 [0x00E90000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
USERDATA : Encrypted
Reading USERDATA will cause large firmware size and slow read speed.
Reading Device Information...OK
Device : Vodafone VFD 511 [msm8909]
Software : VFD-51x_ATPB03, 20170620.061727 [2017年 06月 20日星期二 06:17:28 CST]
Android Ver. : 7.1.1
Patch Level : 2017-03-05
Reading [sbl1]...Done
Reading [sbl1bak]...Done
Reading [rpm]...Done
Reading [rpmbak]...Done
Reading [tz]...Done
Reading [tzbak]...Done
Reading [persist]...Done
Reading [misc]...Done
Reading [aboot]...Done
Reading [abootbak]...Done
Reading [sec]...Done
Reading [modem]...Done
Reading [boot]...Done
Reading [cache]...Done
Reading [recovery]...Done
Reading [splash]...Done
Reading [system]...Done
Reading [gpt_main0]...Done
Reading [gpt_back0]...Done
Saved to : C:\UMTool\QcFire\Read\Vodafone_VFD 511_VFD-51x_ATPB03_2017-03-05\
Operation Finished.
QcFire Ver. 4.1

.::Gsm-Play::. · 04-26-2019, 18:21

Operation : Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM3)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.0.3
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1600500 [8917] 00000000
OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8917_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8917, eMMC, 16 GB
LU Count : 1 [0x01D1F000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : ITEL MOBILE LIMITED itel S42
Software : S42-QL1667-8.0-IN-V027-20180425, IN-V027-20180425 [Wed Apr 25 17:41:49 CST 2018]
Android Ver. : 8.0.0
Patch Level : 2018-05-05
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 4.1

Br,

Yahia_Sb · 04-27-2019, 05:28

mi a2 lite frp done

Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM161)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1600400 [8953] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8953, eMMC, 32 GB
LU Count : 1 [0x03A3E000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Mi A2 Lite
Software : PKQ1.180917.001.V10.0.7.0.PDLMIXM, V10.0.7.0.PDLMIXM [Mon Mar 18 16:20:48 WIB 2019]
Android Ver. : 9
Patch Level : 2019-03-05
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 4.0

sk solution · 04-27-2019, 11:38

Operation : Reset Locks (Vivo)
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.0.3
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1600500 [8917] 00000000
OPK_DATA : 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4F FF8F02A0E7FAD2
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8917_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8917, eMMC, 16 GB
LU Count : 1 [0x01D1F000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : vivo vivo 1724
Software : OPM1.171019.011 release-keys, eng.compil.20181113.225214 [Tue Nov 13 22:52:14 CST 2018]
Android Ver. : 8.1.0
Patch Level : 2018-11-01
USERDATA : Encrypted
Reading Extended Information...OK
Model : vivo 1724
Product : PD1731F_EX
Cust. Name : PD1731F_EX_IN_NULL_NULL
Version : PD1731F_EX_A_1.11.2
Resetting Locks (Vivo)...Done
Please wait for phone to reboot.
Operation Finished.
QcFire Ver. 4.1

sajid01913 · 04-27-2019, 16:44

Xiaomi Redmi 5 Dual MDG1 Mi Account Remove Done

sajid01913 · 04-27-2019, 16:45

Xiaomi Redmi 5 Dual MDG1 Mi Account Remove Done

sajid01913 · 04-27-2019, 16:46

Xiaomi Redmi 5 Dual MDG1 FRP Remove Done

sajid01913 · 04-27-2019, 16:46

Xiaomi Redmi 5 Dual MDG1 FRP Remove Done

VIJAY2U2 · 04-28-2019, 06:38

Code:

Operation	: Reset FRP
Checking for existing devices...Found
Port	: Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info	: Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID	: E1009600 [8909] 00000000
OPK_DATA	: 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A26AB1B4B3F1CF9E
Initializing Protocol...OK
Using Auto Loader Selection [2]
Preparing Loader...Done
Sending Loader [8909_012]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8909, eMMC, 16 GB
LU Count	: 1 [0x01D1F000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device	: itel itel A22 Pro
Software	: V015, A22-PRO-F0901-8.1.0-IN-V015-20180726 [Thu Jul 26 17:37:21 CST 2018]
Android Ver.	: 8.1.0
Patch Level	: 2018-07-05
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 4.1

VIJAY2U2 · 04-28-2019, 06:39

Code:

Device	: Vivo Y95
Operation	: Vivo Format FS / FRP Reset
Checking for existing devices...Found
Port	: Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info	: Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID	: E1F00B00 [8937] 00000000
OPK_DATA	: 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4FFF8F02A0E7FAD2
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_029]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8937, eMMC, 64 GB
LU Count	: 1 [0x0747C000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device	: vivo vivo 1807
Software	: OPM1.171019.026 release-keys, eng.compil.20190401.183815 [Mon Apr  1 18:38:15 CST 2019]
Android Ver.	: 8.1.0
Patch Level	: 2019-03-01
Formatting userdata...Done
Resetting FRP Lock...Done
Wipe cache / userdata from Recovery and reboot.
First startup may take 2-5 minutes.
Operation Finished.
QcFire Ver. 4.1

VIJAY2U2 · 04-28-2019, 07:08

Code:

Operation	: Format FS
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port	: Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info	: Qualcomm Incorporated, qcusbser.sys, 2.1.2.7
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID	: E1600500 [8917] 00000000
OPK_DATA	: 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4FFF8F02A0E7FAD2
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8917_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8917, eMMC, 16 GB
LU Count	: 1 [0x01D5A000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device	: vivo vivo PD1628F_EX [msm8937]
Software	: MMB29M release-keys, eng.compiler.20180810.200649 [Fri Aug 10 20:13:27 CST 2018]
Android Ver.	: 6.0.1
Patch Level	: 2018-08-01
Preparing Data...Done
Formatting Userdata...Done
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 4.1

mabo13 · 04-28-2019, 16:29

Code:

Operation : Reset FRP
CPU : MT6580
Storage : EMMC
DA : MTK_AllInOne_DA.bin [MTK_AllInOne_DA_v3.3001.2017-12-29.16:29]
Waiting for Phone in BROM Mode...
Connect Power Off phone within 30 secs...
Port : PreLoader USB VCOM Port (COM5)
Connected to BROM.
Sending Download Agent...
connect DA end stage: 2, enable DRAM in 1st DA: 0
Connected to Download Agent..
Driver: MediaTek Inc., usbser.sys, 2.0.0.0
Syncing with Target...
Reading Partition Table...
Reading Device Information...
Brand : WIKO
Manufacturer : WIKO
Model : LENNY2
Prod. Name : s5030
Device : s5030
Board : s5030
Platform : mt6580
Android Ver. : 5.1
Display ID : ALPS.L1.MP6.V2_TINNO6580.WE.L
Userdata is NOT ENCRYPTED
Resetting FRP...
FRP Reset Done.
Disconnect Battery/Cable and Power On Phone.
[Ver. 1.8]

sajid01913 · 04-28-2019, 16:43

Itel A32F FRP Remove Done

Operation : Reset FRP
CPU : MT6580
Storage : EMMC
DA : MTK_AllInOne_DA.bin [MTK_AllInOne_DA_v3.3001.2017-12-29.16:29]
Waiting for Phone in BROM Mode...
Connect Power Off phone within 30 secs...
Port : MediaTek PreLoader USB VCOM (Android) (COM4)
Connected to BROM.
Sending Download Agent...
connect DA end stage: 2, enable DRAM in 1st DA: 0
Connected to Download Agent..
Driver: MediaTek Inc., usb2ser.sys, 3.0.1504.0
Syncing with Target...
Reading Partition Table...
Reading Device Information...
Brand : Itel
Manufacturer : itel
Model : itel A32F
Prod. Name : F8007
Device : itel-A32F
Android Ver. : 8.1.0
Patch Level : 2018-06-05
Userdata is ENCRYPTED
Resetting FRP...
FRP Reset Done.
Disconnect Battery/Cable and Power On Phone.
[Ver. 1.9]

sajid01913 · 04-28-2019, 16:44

Itel A32F FRP Remove Done

Operation : Reset FRP
CPU : MT6580
Storage : EMMC
DA : MTK_AllInOne_DA.bin [MTK_AllInOne_DA_v3.3001.2017-12-29.16:29]
Waiting for Phone in BROM Mode...
Connect Power Off phone within 30 secs...
Port : MediaTek PreLoader USB VCOM (Android) (COM4)
Connected to BROM.
Sending Download Agent...
connect DA end stage: 2, enable DRAM in 1st DA: 0
Connected to Download Agent..
Driver: MediaTek Inc., usb2ser.sys, 3.0.1504.0
Syncing with Target...
Reading Partition Table...
Reading Device Information...
Brand : Itel
Manufacturer : itel
Model : itel A32F
Prod. Name : F8007
Device : itel-A32F
Android Ver. : 8.1.0
Patch Level : 2018-06-05
Userdata is ENCRYPTED
Resetting FRP...
FRP Reset Done.
Disconnect Battery/Cable and Power On Phone.
[Ver. 1.9]

neyaz007 · 04-28-2019, 21:34

Operation : Reset Locks (Vivo)
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM98)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1600500 [8917] 00000000
OPK_DATA : 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4F FF8F02A0E7FAD2
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8917_001]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8917, eMMC, 16 GB
LU Count : 1 [0x01D1F000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : vivo vivo 1724
Software : OPM1.171019.011 release-keys, eng.compil.20190325.173405 [Mon Mar 25 17:34:05 CST 2019]
Android Ver. : 8.1.0
Patch Level : 2019-03-01
USERDATA : Encrypted
Reading Extended Information...OK
Model : vivo 1724
Product : PD1731F_EX
Cust. Name : PD1731F_EX_IN_NULL_NULL
Version : PD1731F_EX_A_1.13.3
Resetting Locks (Vivo)...Done
Please wait for phone to reboot.
Operation Finished.

04-26-2019, 17:17	#6751 (permalink)
mickeybrown026 No Life Poster Join Date: Dec 2016 Location: . Posts: 869 Member: 2659717 Status: Offline Thanks Meter: 487	Vfd 513 read firmware done Operation : Read Firmware Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM612) Driver Info : Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1009600 [8909] 00000400 OPK_DATA : BA512444EBFE66557163424226D37E971BFEF7EEE7AE4D70F7 07FA432EF0B039 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8909_038]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8909, eMMC, 8 GB LU Count : 1 [0x00E90000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK USERDATA : Encrypted Reading USERDATA will cause large firmware size and slow read speed. Reading Device Information...OK Device : Vodafone VFD 511 [msm8909] Software : VFD-51x_ATPB03, 20170620.061727 [2017年 06月 20日星期二 06:17:28 CST] Android Ver. : 7.1.1 Patch Level : 2017-03-05 Reading [sbl1]...Done Reading [sbl1bak]...Done Reading [rpm]...Done Reading [rpmbak]...Done Reading [tz]...Done Reading [tzbak]...Done Reading [persist]...Done Reading [misc]...Done Reading [aboot]...Done Reading [abootbak]...Done Reading [sec]...Done Reading [modem]...Done Reading [boot]...Done Reading [cache]...Done Reading [recovery]...Done Reading [splash]...Done Reading [system]...Done Reading [gpt_main0]...Done Reading [gpt_back0]...Done Saved to : C:\UMTool\QcFire\Read\Vodafone_VFD 511_VFD-51x_ATPB03_2017-03-05\ Operation Finished. QcFire Ver. 4.1

04-26-2019, 18:21	#6752 (permalink)
.::Gsm-Play::. No Life Poster Join Date: Jul 2011 Location: Great India Posts: 1,646 Member: 1615596 Status: Offline Sonork: 100.160704? Thanks Meter: 759	Itel S42 Frp Successfully done. Operation : Reset FRP Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM3) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.0.3 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1600500 [8917] 00000000 OPK_DATA : 9CBA94693C2333A562BCF0E0E981C558748817D002F543B2A2 6AB1B4B3F1CF9E Initializing Protocol...OK Using Auto Loader Selection [3] Device may possibly not boot with this loader. Preparing Loader...Done Sending Loader [8917_001]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8917, eMMC, 16 GB LU Count : 1 [0x01D1F000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : ITEL MOBILE LIMITED itel S42 Software : S42-QL1667-8.0-IN-V027-20180425, IN-V027-20180425 [Wed Apr 25 17:41:49 CST 2018] Android Ver. : 8.0.0 Patch Level : 2018-05-05 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 4.1 Br,

04-27-2019, 11:38	#6754 (permalink)
sk solution Insane Poster Join Date: Feb 2019 Location: India Posts: 99 Member: 2892864 Status: Offline Thanks Meter: 74	Vivo Y71 (1724) Lock Reset Done by Umt Operation : Reset Locks (Vivo) Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM5) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.0.3 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1600500 [8917] 00000000 OPK_DATA : 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4F FF8F02A0E7FAD2 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8917_001]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8917, eMMC, 16 GB LU Count : 1 [0x01D1F000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : vivo vivo 1724 Software : OPM1.171019.011 release-keys, eng.compil.20181113.225214 [Tue Nov 13 22:52:14 CST 2018] Android Ver. : 8.1.0 Patch Level : 2018-11-01 USERDATA : Encrypted Reading Extended Information...OK Model : vivo 1724 Product : PD1731F_EX Cust. Name : PD1731F_EX_IN_NULL_NULL Version : PD1731F_EX_A_1.11.2 Resetting Locks (Vivo)...Done Please wait for phone to reboot. Operation Finished. QcFire Ver. 4.1

04-28-2019, 21:34	#6765 (permalink)
neyaz007 Freak Poster Join Date: Nov 2016 Location: India Posts: 150 Member: 2650288 Status: Offline Sonork: live:hackb151 Thanks Meter: 153	vivo y71 1724 Resetting locks succseful umt qcfire Operation : Reset Locks (Vivo) Checking for existing devices...Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Some phones may need Special Boot Cable or TestPoint for EDL mode. Found Port : Qualcomm HS-USB QDLoader 9008 (COM98) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone...OK Waiting for response...OK Init Handshake Sequence...OK Hardware ID : E1600500 [8917] 00000000 OPK_DATA : 30315EBED1DD09CEAAE927CAE0EE967076BC178CA33718DB4F FF8F02A0E7FAD2 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8917_001]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8917, eMMC, 16 GB LU Count : 1 [0x01D1F000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : vivo vivo 1724 Software : OPM1.171019.011 release-keys, eng.compil.20190325.173405 [Mon Mar 25 17:34:05 CST 2019] Android Ver. : 8.1.0 Patch Level : 2019-03-01 USERDATA : Encrypted Reading Extended Information...OK Model : vivo 1724 Product : PD1731F_EX Cust. Name : PD1731F_EX_IN_NULL_NULL Version : PD1731F_EX_A_1.13.3 Resetting Locks (Vivo)...Done Please wait for phone to reboot. Operation Finished.

04-27-2019, 05:28	#6753 (permalink)
Yahia_Sb No Life Poster Join Date: Aug 2014 Posts: 658 Member: 2233266 Status: Offline Thanks Meter: 252	mi a2 lite frp done Operation : Reset FRP Checking for existing devices...Found Port : Qualcomm HS-USB QDLoader 9008 (COM161) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Opening Port...OK Init Handshake Sequence...OK Hardware ID : E1600400 [8953] 00000000 OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Loader...Done Sending Loader [8953]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8953, eMMC, 32 GB LU Count : 1 [0x03A3E000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : Xiaomi Mi A2 Lite Software : PKQ1.180917.001.V10.0.7.0.PDLMIXM, V10.0.7.0.PDLMIXM [Mon Mar 18 16:20:48 WIB 2019] Android Ver. : 9 Patch Level : 2019-03-05 Resetting FRP Lock......Done Operation Finished. QcFire Ver. 4.0

04-27-2019, 16:44	#6755 (permalink)
sajid01913 No Life Poster Join Date: Jul 2008 Location: Bangladesh Posts: 1,255 Member: 821462 Status: Offline Thanks Meter: 833	Xiaomi Redmi 5 Dual MDG1 Mi Account Remove Done

04-27-2019, 16:45	#6756 (permalink)
sajid01913 No Life Poster Join Date: Jul 2008 Location: Bangladesh Posts: 1,255 Member: 821462 Status: Offline Thanks Meter: 833	Xiaomi Redmi 5 Dual MDG1 Mi Account Remove Done

04-27-2019, 16:46	#6757 (permalink)
sajid01913 No Life Poster Join Date: Jul 2008 Location: Bangladesh Posts: 1,255 Member: 821462 Status: Offline Thanks Meter: 833	Xiaomi Redmi 5 Dual MDG1 FRP Remove Done

04-27-2019, 16:46	#6758 (permalink)
sajid01913 No Life Poster Join Date: Jul 2008 Location: Bangladesh Posts: 1,255 Member: 821462 Status: Offline Thanks Meter: 833	Xiaomi Redmi 5 Dual MDG1 FRP Remove Done

04-28-2019, 16:43	#6763 (permalink)
sajid01913 No Life Poster Join Date: Jul 2008 Location: Bangladesh Posts: 1,255 Member: 821462 Status: Offline Thanks Meter: 833	Itel A32F FRP Remove Done Operation : Reset FRP CPU : MT6580 Storage : EMMC DA : MTK_AllInOne_DA.bin [MTK_AllInOne_DA_v3.3001.2017-12-29.16:29] Waiting for Phone in BROM Mode... Connect Power Off phone within 30 secs... Port : MediaTek PreLoader USB VCOM (Android) (COM4) Connected to BROM. Sending Download Agent... connect DA end stage: 2, enable DRAM in 1st DA: 0 Connected to Download Agent.. Driver: MediaTek Inc., usb2ser.sys, 3.0.1504.0 Syncing with Target... Reading Partition Table... Reading Device Information... Brand : Itel Manufacturer : itel Model : itel A32F Prod. Name : F8007 Device : itel-A32F Android Ver. : 8.1.0 Patch Level : 2018-06-05 Userdata is ENCRYPTED Resetting FRP... FRP Reset Done. Disconnect Battery/Cable and Power On Phone. [Ver. 1.9]

04-28-2019, 16:44	#6764 (permalink)
sajid01913 No Life Poster Join Date: Jul 2008 Location: Bangladesh Posts: 1,255 Member: 821462 Status: Offline Thanks Meter: 833	Itel A32F FRP Remove Done Operation : Reset FRP CPU : MT6580 Storage : EMMC DA : MTK_AllInOne_DA.bin [MTK_AllInOne_DA_v3.3001.2017-12-29.16:29] Waiting for Phone in BROM Mode... Connect Power Off phone within 30 secs... Port : MediaTek PreLoader USB VCOM (Android) (COM4) Connected to BROM. Sending Download Agent... connect DA end stage: 2, enable DRAM in 1st DA: 0 Connected to Download Agent.. Driver: MediaTek Inc., usb2ser.sys, 3.0.1504.0 Syncing with Target... Reading Partition Table... Reading Device Information... Brand : Itel Manufacturer : itel Model : itel A32F Prod. Name : F8007 Device : itel-A32F Android Ver. : 8.1.0 Patch Level : 2018-06-05 Userdata is ENCRYPTED Resetting FRP... FRP Reset Done. Disconnect Battery/Cable and Power On Phone. [Ver. 1.9]