WORLD FIRST Mi a1 imei repair done by umt [SUCCESS REPORT]

[Sazidmobile]

1000000% tested by me solutione

[yahiya]

Originally Posted by owais a

in edl mode full efs reset, partition efs reset option which option

Sent from my Redmi Note 4 using Tapatalk

reset efs filed need root

[chandan_123]

my handset mi a1 Diagnostics port not enable.so what to do

[chandan_123]

Port : COM26 : Qualcomm HS-USB Diagnostics 9092 (COM26)
Baud Rate : 921600
Device : Qualcomm Android
Operation : Write IMEI [UMT Method [1]]
Opening Port... OK
Reading Phone Information... OK
Compile : May 4 2018 16:55:18
Release : Jan 02 2018 23:00:00
Hw Ver. : 8953.gen
Build : MPSS.TA.2.3.c1-00544-8953_GEN_PACK-1.130033.1.131132.1
IMEI [1] : 000000000000000
IMEI [2] : 000000000000000
Method : UMT Method [1]
Preparing Data... Done
Writing IMEI 1 [8664090xxxxxxxx]... Done
Writing IMEI 2 [8664090xxxxxxxx]... Done
Rebooting Phone... Done
Please reboot maunally if does not reboot automatically.
Operation Finished.
Elapsed Time: 00:05
[Module Ver. 5.2]
Log Saved to Logs\190324_192723.log

umt show imei write done but after restart set imei 00000000.

[chandan_123]

Operation : Repair IMEI
Searching for Device in FTM Mode...Not Found
Port : COM26 : Qualcomm HS-USB Diagnostics 9092 (COM26)
Compile : May 4 2018 16:55:18
Release : Jan 02 2018 23:00:00
Hw. Ver. : 8953.gen
Software : ----
IMEI : 000000000000000 / 000000000000000
Reading QCN Data...Done
Saved As : C:\UMTool\QcFire\QCN_Backup\8953.gen_----_000000000000000_190324_195657.qcn
Switching to EDL Mode...Failed
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM36)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1600400 [8953] 00000000
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8953, eMMC, 64 GB
LU Count : 1 [0x0747C000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi Mi A1 [msm8953]
Software : OPR1.170623.026.V9.5.11.0.ODHMIFA, V9.5.11.0.ODHMIFA [Fri May 4 18:00:46 WIB 2018]
Android Ver. : 8.0.0
Patch Level : 2018-05-05
Saving EFS Backup.......OK
EFS Backup : EFS_Xiaomi_Mi A1_OPR1.170623.026.V9.5.11.0.ODHMIFA_2018-05-05_190324_200046.ueb
Reset EFS (Full)......Done
Port : COM26 : Qualcomm HS-USB Diagnostics 9092 (COM26)
Processing background tasks...Done
Restoring QCN Data...Done
Finalizing process...Done
Operation Finished.
QcFire Ver. 3.8

not SUCCESS......

[SA1994]

After Reset Efs Phone is dead. I try verious Firmware but phone always only vibrate. Then i change mini Power IC PMI840 my is Ok then i flash firmware 8.1. again my phone is Dead. Again i change PMI8940. I observed that if i short TP with tueser & plug the batery during flashing this model dead dead & dead. Now my phone is OK & working fine

[sohel12]

Port : COM71 : Qualcomm HS-USB Diagnostics 9091 (COM71)
Baud Rate : 921600
Device : Qualcomm Android
Operation : Write IMEI [UMT Method [1]]
Opening Port... OK
Reading Phone Information... OK
Compile : Aug 23 2017 01:50:38
Release : Aug 09 2017 23:00:00
Hw Ver. : 8953.gen
Build : MPSS.TA.2.3.c1-00361-8953_GEN_PACK-1.109159.1.111174.1
IMEI [1] : 350172089765345
IMEI [2] : 350172089765346
Method : UMT Method [1]
Preparing Data... Done
Writing IMEI 1 [350172089765344]... Done
Writing IMEI 2 [350172089765369]... Done
Rebooting Phone... Done
Please reboot maunally if does not reboot automatically.
Operation Finished.
Elapsed Time: 00:07
[Module Ver. 5.2]
Log Saved to Logs\190513_220442.log

dial *#*#717717#*#* or *#*#13491#*#* enable diag port