ZTE Z999 FRP QCFIRE Loader Error

[schizoidcock]

Device : ZTE Axon M (Z999)
Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM3)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000400
OPK_DATA : A8BE927D416A34256605C84FEF2329DF897B51685755AFDE35 3FC8F1EFD5B1C4
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Firehose Loader...Done
Sending Loader [8996_017.ufl]...Error
Please use correct loader and check USB port / cable.
Operation Failed.
Module Ver. 2.4

Any thoughs on this?

[Fast Unlocking]

Please use correct loader and check USB port / cable.

[Elgendi]

Originally Posted by schizoidcock

Device : ZTE Axon M (Z999)
Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM3)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000400
OPK_DATA : A8BE927D416A34256605C84FEF2329DF897B51685755AFDE35 3FC8F1EFD5B1C4
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Firehose Loader...Done
Sending Loader [8996_017.ufl]...Error
Please use correct loader and check USB port / cable.
Operation Failed.
Module Ver. 2.4

Any thoughs on this?

If U Have A firmware Try To Load Loader from Firmware And Must work 1000%

[ocarela]

Originally Posted by Elgendi

If U Have A firmware Try To Load Loader from Firmware And Must work 1000%

i have the firmware how to extract loader?

[PhoneWIZZ]

Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM24)
Driver Info : HS Corporation, ghsser.sys, 10.2104.1.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000400
OPK_DATA : A8BE927D416A34256605C84FEF2329DF897B51685755AFDE35 3FC8F1EFD5B1C4
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8996_017]...Error
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 5.7

[Franky_36]

Originally Posted by PhoneWIZZ

Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM24)
Driver Info : HS Corporation, ghsser.sys, 10.2104.1.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000400
OPK_DATA : A8BE927D416A34256605C84FEF2329DF897B51685755AFDE35 3FC8F1EFD5B1C4
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8996_017]...Error
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 5.7

Hi, the umt qcfire module is on update 6.4, have you tried it? Post the result and log in, thank you very much.

[Franky_36]

Originally Posted by PhoneWIZZ

Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM24)
Driver Info : HS Corporation, ghsser.sys, 10.2104.1.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000400
OPK_DATA : A8BE927D416A34256605C84FEF2329DF897B51685755AFDE35 3FC8F1EFD5B1C4
Initializing Protocol...OK
Using Auto Loader Selection [3]
Device may possibly not boot with this loader.
Preparing Loader...Done
Sending Loader [8996_017]...Error
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 5.7

Hello again, if you tested with the new update of umt qcfire, select ufs, put the phone in edl mode and test, if it gives an error look for the model, anyway I put the link of the loader.

Loader: https://drive.google.com/file/d/1LF2...ew?usp=sharing

[PhoneWIZZ]

same problem on the new verson

[Franky_36]

Originally Posted by PhoneWIZZ

same problem on the new verson

Hi, you know how a forum works and the minimum rules to post in the forum or section, as if we apply them, the exact model, the android system it has, security patch, etc., post operations log and screenshots, you can also use the search option and see if other users have had the same problem or have done the same operation and the result is satisfactory and you only have to apply, it may also happen that the security is very high and the loader does not accept it, then you will have to degrade and do the operation again or do it manually, it depends on the state of the mobile, if it is bricked, it is for frp, etc.

BR

[PhoneWIZZ]

the phone is ok,it is version 7.1.2, u can install apex on it but cant remove the frp,i see many people having a problem with this model,i dont know why is it on the supported list if nobody has managed to do one before

[PhoneWIZZ]

Model: Z999
Serial: 320376660378
Build: N2G47H 7.1.2
Firmware: P996A25V1.0.0B30
CPU: msm8996
Carrier: ATT

[Bscaine]

Still can't do anything to this set;

Device : ZTE Axon M (Z999)
Operation : Read Information
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM155)
Driver Info : HS Corporation, ghsser.sys, 10.2104.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1F00500 [8996] 00000400
OPK_DATA : A8BE927D416A34256605C84FEF2329DF897B51685755AFDE35 3FC8F1EFD5B1C4
Initializing Protocol...OK
Sending Loader [prog_ufs_firehose_8996_ddr.elf]...Error
Please use correct loader and check USB port / cable.
Operation Finished.
QcFire Ver. 6.5

I'm trying to reset unlock counter.
BR

[PhoneWIZZ]

Use octopus frp tool will work