Redmi 6A water damage solution need - GSM-Forum

1plustelecom · 04-23-2019, 13:00

Redmi 6a set water damage . i wash full set fine .but now problem is when i try with new or old battery set not on . but when i put charger white light blinking in the top of the display light near camera right sight light blinking when i put the charger this time only . but set not on . i change display , i change also change another battery same problem set not . also computer not detected . but when i put the power supply then set try to on there voltage goes 0.04/0.05 but when i release the power switch then this volt also drop . please any one help me . sorry for my bad English.
thanks in advanced.

nanechaparmar · 07-23-2019, 13:06

1) check n clen thet section with mor efectet wotar clin it re sold with the help of iran .
2)aftar that remove powar ic & reboll n atech on same pless .
��

venuscell MTC · 09-12-2019, 05:50

when I put the power supply then set try to on there voltage goes 0.04/0.05

make sure about Voltages and current consumption first ...
when the power pushed on ... there's current consumption shown 0.04-0.05 mean 0.040mA or 0.050mA
that's mean the output power has not received to SoC/CPU yet ...
better check all PMU output ...

CMIIW

gsmkasba · 09-19-2019, 19:16

At first check vcc main voltage then vcc vccq vcore vddram voltage if any voltage fluctuating , then trace pmi pm ic wifi ic emmc cpu for shorting or half shorting .......contact me 8709474207 for hardware nd emmc solution......welcome

04-23-2019, 13:00	#1 (permalink)
1plustelecom Freak Poster Join Date: Mar 2018 Posts: 309 Member: 2823049 Status: Offline Thanks Meter: 14	Redmi 6A water damage solution need Redmi 6a set water damage . i wash full set fine .but now problem is when i try with new or old battery set not on . but when i put charger white light blinking in the top of the display light near camera right sight light blinking when i put the charger this time only . but set not on . i change display , i change also change another battery same problem set not . also computer not detected . but when i put the power supply then set try to on there voltage goes 0.04/0.05 but when i release the power switch then this volt also drop . please any one help me . sorry for my bad English. thanks in advanced.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-23-2019, 13:06	#2 (permalink)
nanechaparmar Junior Member Join Date: Nov 2009 Posts: 5 Member: 1167370 Status: Offline Thanks Meter: 0	1) check n clen thet section with mor efectet wotar clin it re sold with the help of iran . 2)aftar that remove powar ic & reboll n atech on same pless . ��

09-12-2019, 05:50	#3 (permalink)
venuscell MTC Crazy Poster Join Date: Jan 2009 Location: Indonesia Posts: 53 Member: 954742 Status: Offline Thanks Meter: 24	when I put the power supply then set try to on there voltage goes 0.04/0.05 make sure about Voltages and current consumption first ... when the power pushed on ... there's current consumption shown 0.04-0.05 mean 0.040mA or 0.050mA that's mean the output power has not received to SoC/CPU yet ... better check all PMU output ... CMIIW

09-19-2019, 19:16	#4 (permalink)
gsmkasba Insane Poster Join Date: Sep 2017 Location: INDIA Posts: 63 Member: 2759692 Status: Offline Sonork: 100.650600 Thanks Meter: 12	At first check vcc main voltage then vcc vccq vcore vddram voltage if any voltage fluctuating , then trace pmi pm ic wifi ic emmc cpu for shorting or half shorting .......contact me 8709474207 for hardware nd emmc solution......welcome