I NEED HELP WITH ALCATEL - GSM-Forum

themobileking · 10-02-2001, 16:11

Dear Friends,

I have 4 alcatel be-1 handsets for repair.All 4 are dead.I've tried to flash and repair all of them but with no result.Andro 5.9 is able to connect and flash them but they refuse to switch on??<br />Somewhere in the forum I once read that there is also a hardware solution for this problem ,by bridging three legs of an ic.which one I've forgotten.<br />I need help.Any suggestions??

regards,

themobileking <img src="biggrin.gif" border="0">

ARC · 10-03-2001, 21:11

Oaoaaaa!

Don't try hardware repair, if your units answered on adnromeda5.9

u have to flash them: (you have software problem)<br />find same FLASH (AMD->AMD) (FUJITSU->FUJITSU)<br />and 1MB->1MB and 2MB->2MB

reflash it, your phone should be swich on after write flash....

if u have backup rewrite it on it's unit and this time try SPLOCK first for all your dead BE1 , if it doesn't work so try full flashing......

Goodluck!

<img src="wink.gif" border="0">

themobileking · 10-06-2001, 13:44

Thanx for the reply but i have already tried that any other suggestions???

MikeDawg · 10-14-2001, 18:24

Use mihnea soft! And if that doesn't work short solder first 3 pins on the ptwl chip, and try with mihnea again.

10-02-2001, 16:11	#1
themobileking No Life Poster Join Date: Jun 2001 Location: Uranus Age: 38 Posts: 724 Member: 5072 Status: Offline Thanks: 0 Thanked 64 Times in 9 Posts	I NEED HELP WITH ALCATEL Dear Friends, I have 4 alcatel be-1 handsets for repair.All 4 are dead.I've tried to flash and repair all of them but with no result.Andro 5.9 is able to connect and flash them but they refuse to switch on??<br />Somewhere in the forum I once read that there is also a hardware solution for this problem ,by bridging three legs of an ic.which one I've forgotten.<br />I need help.Any suggestions?? regards, themobileking <img src="biggrin.gif" border="0">

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-03-2001, 21:11	#2
ARC No Life Poster Join Date: Jun 2001 Location: Pattaya Age: 29 Posts: 1,295 Member: 5019 Status: Offline Sonork: 100.110196 Thanks: 26 Thanked 24 Times in 18 Posts	Oaoaaaa! Don't try hardware repair, if your units answered on adnromeda5.9 u have to flash them: (you have software problem)<br />find same FLASH (AMD->AMD) (FUJITSU->FUJITSU)<br />and 1MB->1MB and 2MB->2MB reflash it, your phone should be swich on after write flash.... if u have backup rewrite it on it's unit and this time try SPLOCK first for all your dead BE1 , if it doesn't work so try full flashing...... Goodluck! <img src="wink.gif" border="0">

10-06-2001, 13:44	#3
themobileking No Life Poster Join Date: Jun 2001 Location: Uranus Age: 38 Posts: 724 Member: 5072 Status: Offline Thanks: 0 Thanked 64 Times in 9 Posts	Thanx for the reply but i have already tried that any other suggestions???

10-14-2001, 18:24	#4
MikeDawg Junior Member Join Date: Mar 2001 Location: Yugoslavia Posts: 12 Member: 3807 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	Use mihnea soft! And if that doesn't work short solder first 3 pins on the ptwl chip, and try with mihnea again.