GSM-Forum - View Single Post - Step by step manual how to repair KMVTU000LM-B503 in pictures.

kococos · 04-08-2015, 10:50

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3269 mV
CMD Active Level:3135 mV
Can't init device, Reason: OCR Ready Timeout Error [EMMC DEAD]
Done.

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3279 mV
CMD Active Level:3135 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150303_1640.extcsd
Done.

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM-B503
Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3279 mV
CMD Active Level:3124 mV
Setup firmware normal update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Can't init device, Reason: CMD Timeout Error
Done.

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM-B503
Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3279 mV
CMD Active Level:3135 mV
Setup firmware normal update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect eMMC power lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

Nice update...

04-08-2015, 10:50	#18 (permalink)
kococos Insane Poster Join Date: Nov 2007 Location: Bandung, west java Age: 44 Posts: 73 Member: 624775 Status: Offline Thanks Meter: 18	Z3X EasyJtag Software ver. 1.9.0.5 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52 CMD Pullup Level:3269 mV CMD Active Level:3135 mV Can't init device, Reason: OCR Ready Timeout Error [EMMC DEAD] Done. Z3X EasyJtag Software ver. 1.9.0.5 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52 CMD Pullup Level:3279 mV CMD Active Level:3135 mV eMMC Device Information EMMC CID : 1501003030303030305620110726589C EMMC CSD : 902701320F5903FFF6DBFFEF8A404022 EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 05/2005 Rev.0x56 EMMC NAME: 000000 , S/N: 537986854 EMMC NAME (HEX): 30303030303000 EMMC ROM1 (Main User Data) Capacity: 16384 MB EMMC ROM2 (Boot Partition 1) Capacity: 512 kB EMMC ROM3 (Boot Partition 2) Capacity: 512 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: 000000_ 537986854_20150303_1640.extcsd Done. Running:SAMSUNG: eMMC firmware update... Confirmed eMMC Part Number: KMVTU000LM-B503 Z3X EasyJtag Software ver. 1.9.0.5 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52 CMD Pullup Level:3279 mV CMD Active Level:3124 mV Setup firmware normal update mode, wait 2..30 sec... Success! Sending eMMC firmware... Success! Verifying eMMC firmware... Success! Flashing eMMC firmware... Success! Repairing eMMC CID... Can't init device, Reason: CMD Timeout Error Done. Running:SAMSUNG: eMMC firmware update... Confirmed eMMC Part Number: KMVTU000LM-B503 Z3X EasyJtag Software ver. 1.9.0.5 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52 CMD Pullup Level:3279 mV CMD Active Level:3135 mV Setup firmware normal update mode, wait 2..30 sec... Success! Sending eMMC firmware... Success! Verifying eMMC firmware... Success! Flashing eMMC firmware... Success! Repairing eMMC CID... Success! eMMC firmware is updated now! Please reconnect eMMC power lines before next operation! Please don't forget to repair extCSD from backup! Please don't forget to configure BOOT sizes! Done. Nice update...