Card found: S/N : 4DFB0B9F , v0122
Registered to: vishnu
Connect phone on selected interface...
Core : v2.23 , MTKx FlashEngine : v10.1
Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 121 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 1A1596A48AA57CED6E48B0028CFAAC85
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Connect phone on selected interface...
Switch to BL failed! (CMD not accepted, 0xAA)
Check Power / Cable!
BootLoader Init Failed (HW/Connection Error)
Connect phone on selected interface...
Boot Error
Flashing failed!
Connect phone on selected interface...
Core : v2.23 , MTKx FlashEngine : v10.1
Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
- > MODE : FullFlash
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 121 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 1A1596A48AA57CED6E48B0028CFAAC85
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Connect phone on selected interface...
Switch to BL failed! (CMD not accepted, 0xAA)
Check Power / Cable!
BootLoader Init Failed (HW/Connection Error)
Connect phone on selected interface...
Boot Error
Flashing failed!
Connect phone on selected interface...
Core : v2.23 , MTKx FlashEngine : v10.1
Verify files ...
MAUI : RM-1035_ROM_eMP_10.01.11
VIVA : RM-1035_VIVA_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
JMPT : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
- > MODE : FullFlash
Repair Mode is On
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 121 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : 1A1596A48AA57CED6E48B0028CFAAC85
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]........
nokia 130 flashing error any one has solution plz help |