GSM-Forum - View Single Post - 🐙 Post here success Reset FRP story with Octoplus FRP Tool

maxpatri9 · 04-27-2018, 16:01

SEL

SELECT N920P USING UFS METHOT
Welcome to Octoplus FRP Tool v.1.2.4
Platform: SAMSUNG
Selected model: SM-N920P
To put SM-N920P into Download Mode, You have to perform the following steps:
1. Reconnect the battery.
2. Press and hold "Volume-" + "Home" + "Power ON" keys.
3. When phone turns on, press "Volume+" key.
Searching for a phone. Please wait...
Phone found.
Initializing..
PIT was read successfully.
Searching for UART interface.. COM48
Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Resetting FRP lock..
FRP lock is successfully reseted!
Wait 3-4 min then goto "Menu -> Settings -> Backup and reset" and make "Factory data reset"
Performed by 1.2.4.0 Software version.

Platform: SAMSUNG
Selected model: SM-N920P
ADB server killed.
Please, press "OK" button on the phone to allow USB debugging..
Warning: Selected model (SM-N920P) differs from the detected one (SM-N920R4)!
If you want select (SM-N920R4) as (SM-N920P) model, please check "manual select".
Operation was failed!
Performed by 1.2.4.0 Software version.

Platform: SAMSUNG
Selected model: SM-N920P
Selected port: COM1
Detected phone model: SM-N920R4
Firmware compiled date: Thu Jun 15 15:01:41 KST 2017
PDA version: N920R4TYU3CQF2
CSC version: N920R4USC3CQF2
SW version: N920R4TYU3CQF2
Phone SN: 00000000000
Android version: 7.0 (NRD90M)
Sales code: USC
Country: USA
HW platform: exynos5
HW Chip: exynos7420
HW Modem: MDM9635M
Security patch level: 2017-06-01
Codename: noblelteusc
Performed by 1.2.4.0 Software version.

04-27-2018, 16:01	#572 (permalink)
maxpatri9 No Life Poster Join Date: Apr 2015 Location: Dominican Republic Posts: 2,564 Member: 2382052 Status: Offline Thanks Meter: 1,511	🐙 Samsung SM-N920R4 Reset FRP successfully done SEL SELECT N920P USING UFS METHOT Welcome to Octoplus FRP Tool v.1.2.4 Platform: SAMSUNG Selected model: SM-N920P To put SM-N920P into Download Mode, You have to perform the following steps: 1. Reconnect the battery. 2. Press and hold "Volume-" + "Home" + "Power ON" keys. 3. When phone turns on, press "Volume+" key. Searching for a phone. Please wait... Phone found. Initializing.. PIT was read successfully. Searching for UART interface.. COM48 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Resetting FRP lock.. FRP lock is successfully reseted! Wait 3-4 min then goto "Menu -> Settings -> Backup and reset" and make "Factory data reset" Performed by 1.2.4.0 Software version. Platform: SAMSUNG Selected model: SM-N920P ADB server killed. Please, press "OK" button on the phone to allow USB debugging.. Warning: Selected model (SM-N920P) differs from the detected one (SM-N920R4)! If you want select (SM-N920R4) as (SM-N920P) model, please check "manual select". Operation was failed! Performed by 1.2.4.0 Software version. Platform: SAMSUNG Selected model: SM-N920P Selected port: COM1 Detected phone model: SM-N920R4 Firmware compiled date: Thu Jun 15 15:01:41 KST 2017 PDA version: N920R4TYU3CQF2 CSC version: N920R4USC3CQF2 SW version: N920R4TYU3CQF2 Phone SN: 00000000000 Android version: 7.0 (NRD90M) Sales code: USC Country: USA HW platform: exynos5 HW Chip: exynos7420 HW Modem: MDM9635M Security patch level: 2017-06-01 Codename: noblelteusc Performed by 1.2.4.0 Software version.