GSM-Forum - View Single Post - j100h too many error writing has been stop

engcobocell · 06-19-2018, 07:12

and now these showing am sorry am new with JTAG
Loading eMMC GEN2 Firmware... IO: 2800 mV
Box S/N: 16F03C9E6AE1BE10, ,FW Ver.: 02.23
CMD Pullup Level:2186 mV
CMD Active Level:2551 mV
Box IO Level:2800 mV
CLK Rate:24000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

EMMC CID : 90014A4834473262110190A76A6082A5
EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 08/2015 Rev.0x1
EMMC NAME: H4G2b , S/N: 2426890848
EMMC NAME (HEX): 48344732622000
EMMC ROM1 (Main User Data) Capacity: 3728 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: H4G2b _2426890848_20180618_2255.extcsd
Done.

Checking NAND Image : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Autodetected RAW data
Warning! Disk size is smaller than the main header indicates! Loading
Caution: invalid backup GPT header, but valid main header!
EFI Table CRC Check FAIL.
Warning! One or more CRCs don't match. You should repair the disk!
Partition table scan:
GPT: damaged
Caution: Found protective or hybrid MBR and corrupt GPT.
Partition info successfully found
Linux partitions is not found in image...
File successefuly loaded!

Real (Hardware) Disk/Image size: 200000 sectors 1024.0 MiB
Soft (Partitioned) Disk/Image size: 743FBC sectors 3.6 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
First usable sector: 34
Last usable sector: 7618526
Processing file...D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Writing as RAW data
Checking security ...
Z3X EasyJtag Software ver. 2.9.0.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2191 mV
CMD Active Level:2789 mV
Input file : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Writing 0040000000 bytes to 0000000000... ROM1 (USER ROM)
Error writing address 0x38220000 Error Code:-4 Reason

ATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...
Retry failed at address 0x38220000 Error Code:-4 Reason

ATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...

06-19-2018, 07:12	#4 (permalink)
engcobocell No Life Poster Join Date: Jun 2016 Location: every ware in your hart Posts: 798 Member: 2590583 Status: Offline Thanks Meter: 198	and now these showing am sorry am new with JTAG Loading eMMC GEN2 Firmware... IO: 2800 mV Box S/N: 16F03C9E6AE1BE10, ,FW Ver.: 02.23 CMD Pullup Level:2186 mV CMD Active Level:2551 mV Box IO Level:2800 mV CLK Rate:24000 kHz Bus Width:1bit,SDR HiPower mode is ON! ---------- eMMC Device Information ---------- EMMC CID : 90014A4834473262110190A76A6082A5 EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacturer ID: 0090 , OEM ID: 014A EMMC Date: 08/2015 Rev.0x1 EMMC NAME: H4G2b , S/N: 2426890848 EMMC NAME (HEX): 48344732622000 EMMC ROM1 (Main User Data) Capacity: 3728 MB EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: No Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08. H/W reset function [RST_N_FUNCTION]: 0x00 High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000] Partitioning Support [PARTITIONING_SUPPORT]: 0x07 Device support partitioning feature Device can have enhanced tech. Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00 --------------------------------------------- Backup saved: H4G2b _2426890848_20180618_2255.extcsd Done. Checking NAND Image : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin Autodetected RAW data Warning! Disk size is smaller than the main header indicates! Loading Caution: invalid backup GPT header, but valid main header! EFI Table CRC Check FAIL. Warning! One or more CRCs don't match. You should repair the disk! Partition table scan: GPT: damaged Caution: Found protective or hybrid MBR and corrupt GPT. Partition info successfully found Linux partitions is not found in image... File successefuly loaded! Real (Hardware) Disk/Image size: 200000 sectors 1024.0 MiB Soft (Partitioned) Disk/Image size: 743FBC sectors 3.6 GiB Logical sector size: 0x200 bytes Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B First usable sector: 34 Last usable sector: 7618526 Processing file...D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin Writing as RAW data Checking security ... Z3X EasyJtag Software ver. 2.9.0.3 Skip loading eMMC Addon Firmware CMD Pullup Level:2191 mV CMD Active Level:2789 mV Input file : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin Writing 0040000000 bytes to 0000000000... ROM1 (USER ROM) Error writing address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)... Retry failed at address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)... Retry failed at address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)... Retry failed at address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)...