View Single Post
Old 09-29-2019, 06:46   #7714 (permalink)
VIJAY2U2
No Life Poster
 
VIJAY2U2's Avatar
 
Join Date: Apr 2008
Location: India
Posts: 3,538
Member: 1039903
Status: Offline
Thanks Meter: 2,040
Redmi 5 MI ACC+FRP

Code:
Operation	: Reset Mi Account
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port	: Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info	: Qualcomm Incorporated, qcusbser.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID	: E1A00900 [8953] 00000000
OPK_DATA	: 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953_009]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8953, eMMC, 16 GB
LU Count	: 1 [0x01D5A000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device	: Xiaomi Redmi 5 [msm8953] [rosy]
Software	: N2G47H, V9.2.3.0.NDAMIEK [Mon Jan 15 23:24:28 WIB 2018]
Android Ver.	: 7.1.2
Patch Level	: 2018-01-01
Resetting Mi Account Data...Done
When phone is completely ON, connect to Internet and add Mi Account.
-------------- INFORMATION --------------
New Firmware may cause hang on logo.
In such case, you need to flash phone to recover.
Or downgrade firmware and try Reset Mi Account again.
Operation Finished.
QcFire Ver. 4.7

Code:
Operation	: Reset FRP
Checking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port	: Qualcomm HS-USB QDLoader 9008 (COM5)
Driver Info	: Qualcomm Incorporated, qcusbser.sys, 2.1.2.0
Connecting to phone...OK
Waiting for response...Ignored
Init Handshake Sequence...OK
Hardware ID	: E1A00900 [8953] 00000000
OPK_DATA	: 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8953_009]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8953, eMMC, 16 GB
LU Count	: 1 [0x01D5A000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device	: Xiaomi Redmi 5 [msm8953] [rosy]
Software	: N2G47H, V9.2.3.0.NDAMIEK [Mon Jan 15 23:24:28 WIB 2018]
Android Ver.	: 7.1.2
Patch Level	: 2018-01-01
Resetting FRP Lock......Done
Operation Finished.
QcFire Ver. 4.7
  Reply With Quote
The Following 2 Users Say Thank You to VIJAY2U2 For This Useful Post:
 
Page generated in 0.07820 seconds with 7 queries