| Nokia 130 RM-1035 Restart and Blinking Keypad Done
Card found : A9EC786B , v0122
Infinity-Box BEST Nokia [HMD] Module [NK2] v1.20
Open VPLfile : RM1035_059W057_10.01.11.vpl
Description : RM-1035 NDT INDIA MH LATIN IN
DeviceType : RM-1035
ProductCode : 059W057
SoftwareVer : 10.01.11
PPM LangPack :
[1] : Gujarati (India)
[2] : Kannada (India)
[3] : Marathi (India)
[4] : Telugu (India)
[5] : Punjabi (India)
[6] : Tamil (India)
[7] : Hindi (India)
[8] : Urdu (Islamic Republic of Pakistan)
[9] : English (United Kingdom)
Load Ok!
Operation : Write FirmWare [ v1.20 ]
Setting : UserData erase : False
Setting : LangPack Only : False
1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : Nokia USB Serial Port (COM18)
MODE : NOKIA USB SERIAL
PORT : 18
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 6FEF32034B4E5D29AFD020BC8BFA3B0B
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : CRYSTAL.10.01.11.p2
BOOT : SWR : 10.01.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : CRYSTAL.10.01.11.p2
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B
NOR: 00EF : 0040 : 0016 : 0000
NOR: [WINBOND] W25Q32BV
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST
STATUS : OK
BSTYLE : SF_FLASH_BOOT
Boot done!
VPL SoftwareVersion : 10.01.11 [RM-1035]
DEV SoftwareVersion : 10.01.11
SWInfo compare result : SAME
Load FlashSet :
MROM : RM-1035_ROM_eMP_10.01.11
LANG : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
CUST : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
JUMP : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
VIVA : RM-1035_VIVA_eMP_10.01.11
Prepare FlashSet :
DCR : RM-1035_ROM_eMP_10.01.11
DCR : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
DCR : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
DCR : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
DCR : RM-1035_VIVA_eMP_10.01.11
Prepare Target
SDS : OK : 0x003F4000 : 0x0000C000
CBR : 0x0000001A:0x00000001:0x00000000:0x00000000:0x0000 0010:0x00000002:0x00000000
Erase Target Flash
Erase done!
Write Target Flash
Write : RM-1035_ROM_eMP_10.01.11
Write : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
Write : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
Write : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
Write : RM-1035_VIVA_eMP_10.01.11
Write done, waiting target response ...
Write flash done!
Verify Target FlashContent
Verify : RM-1035_ROM_eMP_10.01.11
Verify : RM-1035_LANG_PACK_ROM_MH_eMP_10.01.11_001
Verify : RM-1035_CUSTPACK_ROM_MH_INDIA_IN_eMP_10.01.11_001
Verify : RM-1035_JUMP_TABLE_MH_INDIA_IN_eMP_10.01.11_001
Verify : RM-1035_VIVA_eMP_10.01.11
Done!
Elapsed: 00:01:17
Reconnect Power/Cable! |