View Single Post
Old 09-17-2020, 16:40   #4 (permalink)
Chijohn
Freak Poster
 
Join Date: May 2020
Location: Globe
Posts: 249
Member: 2955840
Status: Offline
Thanks Meter: 79
Quote:
Originally Posted by Manikanika81 View Post
I understand now, emmc read-only.

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 119 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384545380119FEDC44A537
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EE8H
[eMMC] : FLASH_CID : 7001004548384545380119FEDC44A537
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2800000
[eMMC] : FLASH_UCP : 7464 MiB [eMMC 8 GiB]
DEV RID : 0x81F00D0F78DDB544370E3CE88CFB04E9
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand : Itel
ProdName : F8019
ProdModel : itel W5003
Device : itel-W5003
AndroidVer: 8.1.0

Done!
Elapsed: 00:00:06
Reconnect Power/Ca

Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 119 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004548384545380119FEDC44A537
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 8EE8H
[eMMC] : FLASH_CID : 7001004548384545380119FEDC44A537
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2800000
[eMMC] : FLASH_UCP : 7464 MiB [eMMC 8 GiB]
DEV RID : 0x81F00D0F78DDB544370E3CE88CFB04E9
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!


[Processing] FlashMemory Read-Write test
[eMMC] : [KINGSTON] , 8EE8H , 0x1D2800000 , 7464 MiB
[eMMC] : CID : 7001004548384545380119FEDC44A537

[eMMC] : MODE : SQ-WR
[FAILED : READONLY] : eMMC state seems as READ-ONLY !!!!

Operation Failed
Elapsed: 00:00:38
Reconnect Power/Cable!
Readonly means EMMC is bad. You can't write anything than to change EMMC.
  Reply With Quote
 
Page generated in 0.07760 seconds with 7 queries