HELLO
PHONE WAS OKI ONLY LOCK CODE
AFTER FLASH ONLY VIBRATE
TRIED 2 FIRMWARE SAME ISSUE
Connect phone on selected interface...
Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Read Uniq key data started...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
-> Phone not found..
Fetching failed!
Connect phone on selected interface...
Read fail...!
Connect phone on selected interface...
Reading Phone Info....
Connected phone - Error
Software ver : Error
IMEI : Error
XappVer : 000008F2
Ape Ver : Error
APE Var : Error
APE ADSP: Error
DSP Ver : Error
APE Test: Error
PPM : Error
CNT : Error
Product SN : Error
Product code : Error
Base Prd.code: Error
Module code : Error
Long Prod.SN : Error
Hardware info=======
HWID : Error
Retu : Error
Tahvo : Error
Battery: 0 mV
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: Error
Lock info ===========
IMEI : Error
IMEI spNet :
IMEI svNet :
Unable to read Lock table...
Error collect lock info, try again
Error, when try do backup CRT308
SDD key status : Error Read Info
CMLA Key status : Not Present
SimLock status : Damaged!!!!!
Security status : Damaged!!!!!
Reading Phone Info....
Connected phone - Error
Software ver : Error
IMEI : Error
XappVer : 000008F2
Ape Ver : Error
APE Var : Error
APE ADSP: Error
DSP Ver : Error
APE Test: Error
PPM : Error
CNT : Error
Product SN : Error
Product code : Error
Base Prd.code: Error
Module code : Error
Long Prod.SN : Error
Hardware info=======
HWID : Error
Retu : Error
Tahvo : Error
Battery: 0 mV
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: Error
Lock info ===========
IMEI : Error
IMEI spNet :
IMEI svNet :
Unable to read Lock table...
Error collect lock info, try again
Error, when try do backup CRT308
SDD key status : Error Read Info
CMLA Key status : Not Present
SimLock status : Damaged!!!!!
Security status : Damaged!!!!!
Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
- > If phone can't switch to BL - use battery or flash from Local mode!
--- Insert USB cable now! ---
Wait for phone...
Device boot not done
Check Drivers
Try again
Phone found!
Series 60 Device detected!
read info... - Ok
Connect phone on selected interface...
Read Uniq key data started...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
-> Phone not found..
Fetching failed!
Connect phone on selected interface...
Read fail...!
Connect phone on selected interface...
Phone found!
Series 60 Device detected!
read info... - Ok
Phone disconected!
Connect phone on selected interface...
Backup Certificates now...
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
-> Phone not found..
Looks like ASIC not supported, or HW failure
Supported : RapuYamaVx, RAP3Gv4, BroadComm, RAPIDO, XG213, XG221, XG223, XG618
Phone found!
Series 60 Device detected!
read info... - Ok
Phone disconected!
Connect phone on selected interface...
-> Phone not found..
Looks like ASIC not supported, or HW failure
Supported : RapuYamaVx, RAP3Gv4, BroadComm, RAPIDO, XG213, XG221, XG223, XG618
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_m3
CNT : rm948__10.24.image_m3_059T320
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527994
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_m3_059T320
Region count : 1
00 : [ Cust ] : package_m3_059T320.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059T320.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02013400
Region Load done
Write done
package_m3_059T320.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
- > AfterFlash Failed!
Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:03:01
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_m3
CNT : rm948__10.24.image_m3_059T320
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527994
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_m3_059T320
Region count : 1
00 : [ Cust ] : package_m3_059T320.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059T320.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02013400
Region Load done
Write done
package_m3_059T320.image.fls image flash done
Flashing done!
Total flash time : 00:00:12
Reboot phone now...
- > AfterFlash Failed!
Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:03:15
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__10.24.mcusw
PPM : rm948__10.24.ppm_m3
CNT : rm948__10.24.image_m3_059T320
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1340.100_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__10.24.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__10.24.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__10.24.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F5AFCC
Region Load done
Write done
rm948__10.24.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C278E0
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x00149A78
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__10.24.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00527994
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__10.24.image_m3_059T320
Region count : 1
00 : [ Cust ] : package_m3_059T320.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059T320.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x02013400
Region Load done
Write done
package_m3_059T320.image.fls image flash done
Flashing done!
Total flash time : 00:00:14
Reboot phone now...
- > AfterFlash Failed!
Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy
Connect phone on selected interface...
Done!
Connect phone on selected interface...
Elapsed: 00:02:30
Connect phone on selected interface...
Core : v2.29 , BB5XG FlashEngine : v10.5
Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm948__04.06.mcusw
PPM : rm948__04.06.ppm_m3
CNT : rm948__04.06.image_m3_059S6T2
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---
Connection opened successfully
IF Boot Init : 0xF0
IF Resp Len : 0x16
IF xCPUID : XGOLD 618 [XMM6180 QUARK]
IF uCHIPID : 50A9070100030101E010040940049752480E19B6FFFF
IF Resp Data : 50A9070100030101
Wait for user action : Insert battery
Sending EBL Loader ...
EBL Loader Ok
EBL Loader ready
Sending EBL ...
EBL sent Ok
EBL : QUARK_1327.300_M1S1
QUARK EEP config Ok
FLASHID : 20004000 , [ MuxOneNAND ]
Boot conf set, Target Ready
Boot done!
Backup enabled, will read all certificates
RPL saved : D:\BST\BEST\Backup\Cert\_2nd_XG618_SIM.rpl
===Flashing [MCU]===
Processing file : rm948__04.06.mcusw
Region count : 8
00 : [ PSI ] : psi_flash_unsigned.fls
01 : [ BCore ] : slb_signed.fls
02 : [ Code ] : main_toc_signed.fls
03 : [ Code ] : rm948__04.06.mcusw_signed_mcusw.fls
04 : [ Code ] : swap_signed.fls
05 : [ Cust ] : dynsw.fls
06 : [ Code ] : aeneas_signed.fls
07 : [ Code ] : fota_signed.fls
Parse done , flashing now
Flash : 00 : psi_flash_unsigned.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x00090000 , Len : 0x00020000
Erase now...
Erase done
Region Start : 0x00090000 , Data Len : 0x00010FB0
Region Load done
Write done
psi_flash_unsigned.fls image flash done
Flash : 01 : slb_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0001 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60000000 , Len : 0x00040000
Erase now...
Erase done
Region Start : 0x60000000 , Data Len : 0x00040000
Region Load done
Write done
slb_signed.fls image flash done
Flash : 02 : main_toc_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0002 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x60040000 , Len : 0x00000400
Erase now...
Erase done
Region Start : 0x60040000 , Data Len : 0x00000400
Region Load done
Write done
main_toc_signed.fls image flash done
Flash : 03 : rm948__04.06.mcusw_signed_mcusw.fls
Sending Sec-Pack
SecInfo Area : 0x0003 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62E00000 , Len : 0x01100000
Erase now...
Erase done
Erase area 0x01 , Start 0xFFF00000 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x62E00000 , Data Len : 0x00F3A664
Region Load done
Write done
rm948__04.06.mcusw_signed_mcusw.fls image flash done
Flash : 04 : swap_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0004 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80000000 , Len : 0x00F00000
Erase now...
Erase done
Region Start : 0x80000000 , Data Len : 0x00C22738
Region Load done
Write done
swap_signed.fls image flash done
Flash : 05 : dynsw.fls
Sending Sec-Pack
SecInfo Area : 0x0005 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x62080000 , Len : 0x00100000
Erase now...
Erase done
Region Start : 0x62080000 , Data Len : 0x00044000
Region Load done
Write done
dynsw.fls image flash done
Flash : 06 : aeneas_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0006 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x63F79C00 , Len : 0x00080000
Erase now...
Erase done
Region Start : 0x63F79C00 , Data Len : 0x00046870
Region Load done
Write done
aeneas_signed.fls image flash done
Flash : 07 : fota_signed.fls
Sending Sec-Pack
SecInfo Area : 0x0007 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x61F00004 , Len : 0x0017FFFC
Erase now...
Erase done
Region Start : 0x61F00004 , Data Len : 0x001464A4
Region Load done
Write done
fota_signed.fls image flash done
===Flashing [PPM]===
Processing file : rm948__04.06.ppm_m3
Region count : 1
00 : [ Cust ] : package_m3.ppm_ebl_psi.fls
Parse done , flashing now
Flash : 00 : package_m3.ppm_ebl_psi.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0x80F00000 , Len : 0x00B00000
Erase now...
Erase done
Region Start : 0x80F00000 , Data Len : 0x00526DF4
Region Load done
Write done
package_m3.ppm_ebl_psi.fls image flash done
===Flashing [CNT]===
Processing file : rm948__04.06.image_m3_059S6T2
Region count : 1
00 : [ Cust ] : package_m3_059S6T2.image.fls
Parse done , flashing now
Flash : 00 : package_m3_059S6T2.image.fls
Sending Sec-Pack
SecInfo Area : 0x0000 , SecInfo Len : 0x0800
Erase area 0x00 , Start 0xA1000000 , Len : 0x0C580000
Erase now...
Erase done
Erase area 0x01 , Start 0xAE000000 , Len : 0x00300000
Erase now...
Erase done
Region Start : 0xA1000000 , Data Len : 0x01D92400
Region Load done
Write done
package_m3_059S6T2.image.fls image flash done
Flashing done!
Total flash time : 00:00:11
Reboot phone now...