View Single Post
Old 12-19-2021, 09:58   #1 (permalink)
alamgarh
No Life Poster
 
alamgarh's Avatar
 
Join Date: Sep 2006
Location: MX-KEY is the BEST NOKIA TOOL
Posts: 4,503
Member: 358694
Status: Offline
Sonork: 100.1597323
Thanks Meter: 939
Kmdx60018m firmware update failed

https://forum.gsmhosting.com/vbb/f67...0018m-2987401/

i got this firmware from easy jtag folder but cannot update to emmc.

but if i try to update firmware with ufi its updated but phone only detected as exynos


eMMC CID : 150100303030303030562016061354D1
eMMC CSD : 902701320F5903FFF6DB7FE08A40403B
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2017 Rev.0x56
eMMC NAME: 000000 , S/N: 538314259
eMMC NAME (HEX): 303030303030
EMMC ROM1 (Main User Data) Capacity: 2095982 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC RPMB is not yet programmed (clear) or RPMB Counter failure
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: 000000_ 538314259_20211219_1048.extcsd
Blocks Reading Error (0x0 , 1 , Reason: DATA RCV Timeout Error )
Blocks Reading Error (0x200 , 1 , Reason: DATA RCV Timeout Error )
Warning! Read error 0 strange behavior now likely!
Blocks Reading Error (0x1FFB6DFFE00 , 1 , Reason: DATA RCV Timeout Error )
Warning! Read error 0 strange behavior now likely!
Partition info not found
Done.


fw update failed



and


and


Running:SAMSUNG: eMMC firmware update...
Chip Init OK...
Downloading FFU:C:\Program Files\Z3X\EASYJTAG\eMMC Firmware\KMDX60018M-B425_DX68MB.bin
Checking security ...
Z3X EasyJtag Software ver. 3.7.0.24
Checking firmware type...
OK;
Skip loading eMMC Addon Firmware
Box S/N: 553E579F73FF53EF, ,FW Ver.: 02.53
CMD Pullup Level:2088 mV
CMD Active Level:2272 mV
Box IO Level:3000 mV
CLK Rate:14000 kHz
Using firmware file : C:\Program Files\Z3X\EASYJTAG\eMMC Firmware\KMDX60018M-B425_DX68MB.bin
Update Firmware ID Hash:
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Can't send eMMC firmware, Reason: DATA RCV CRC Error
Done.
Attached Images
File Type: jpg 1.jpg (250.9 KB, 56 views)
File Type: jpg 2.jpg (265.0 KB, 56 views)
File Type: jpg 3.jpg (263.3 KB, 56 views)
  Reply With Quote
 
Page generated in 0.08253 seconds with 8 queries