| UFS FAILED TO WRITE ANY PARTITION VIA EMMC MODULE
Operation: Connect to Z3X EasyJtagPlus
Setting Interface to EasyJtag2/UFS-Socket
Setting IO Levels to High
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-254 by EasyJTAG 28.01.21
Socket Serial: 0123B2BACF15DFB8EE
Socket Type: UFS_SOCKET_BGA_254
UFS Power Information :
Mode: High, VCC: 3320 mV, VCCQ2: 1921 mV
UFS Device Information :
UFS Manufacturer: SAMSUNG, UFS ProductName: KLUDG4UHDB-B2D1
UFS OemID: SAMSUNG_OEM_ID, UFS SerialNumber: 0x42711DDD3B197EBD8EE222C4E68153414B503230304B
Maximum Number of LUs: 8, Number of LUs found: 5, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 13683
UFS LUN 0 Capacity: 122008 MB (001DC9800000)
UFS LUN 1 (Boot A) Capacity: 4 MB (000000400000)
UFS LUN 2 (Boot B) Capacity: 4 MB (000000400000)
UFS LUN 3 Capacity: 8 MB (000000800000)
UFS LUN 4 Capacity: 16 MB (000001000000)
UFS W-LUN 0xC4 (RPMB) Capacity: 16 MB (000001000000)
Device Life Time Estimation B: 0x02 10% - 20% device life time used
Device Life Time Estimation A: 0x02 10% - 20% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Reading by Vendor (Binary Read/Write)
Output Directory: C:\Users\DROID\Desktop\G980F\DUMP\
Reading: LUN 1 (Boot A), Offset: 0x000000000000, Size: 0x000000400000 (4.00 MB)
Output file: LUN 1 (Boot A)_000000000000_000000400000.bin
Reading partition...
Error: Previous operation is not finished yet
Error: Previous operation is not finished yet
Error reading at address: 000000000000 , error: -205, Unknown error: -205 ... Retry #1
Error reading at address: 000000000000 , error: -205, Unknown error: -205 ... Retry #2
Error reading at address: 000000000000 , error: -205, Unknown error: -205 ... Retry #3
Too many errors. Reading has been stopped
Disconnected
Operation: Connect to Z3X EasyJtagPlus
Setting Interface to EasyJtag2/UFS-Socket
Setting IO Levels to High
Setting Frequence to 66 Mhz
Socket Information :
Socket Mark: EasyJTAG UFS Socket BGA-254 by EasyJTAG 28.01.21
Socket Serial: 0123B2BACF15DFB8EE
Socket Type: UFS_SOCKET_BGA_254
UFS Power Information :
Mode: High, VCC: 3321 mV, VCCQ2: 1922 mV
UFS Device Information :
UFS Manufacturer: SAMSUNG, UFS ProductName: KLUDG4UHDB-B2D1
UFS OemID: SAMSUNG_OEM_ID, UFS SerialNumber: 0x42711DDD3B197EBD8EE222C4E68153414B503230304B
Maximum Number of LUs: 8, Number of LUs found: 5, Number of WLUs found: 1, LUs Re-configure: Enabled
RPMB Counter: 13683
UFS LUN 0 Capacity: 122008 MB (001DC9800000)
UFS LUN 1 (Boot A) Capacity: 4 MB (000000400000)
UFS LUN 2 (Boot B) Capacity: 4 MB (000000400000)
UFS LUN 3 Capacity: 8 MB (000000800000)
UFS LUN 4 Capacity: 16 MB (000001000000)
UFS W-LUN 0xC4 (RPMB) Capacity: 16 MB (000001000000)
Device Life Time Estimation B: 0x02 10% - 20% device life time used
Device Life Time Estimation A: 0x02 10% - 20% device life time used
Pre EOL information: 0x01 Normal (Consumed less then 80% of reserved block)
Do not turn the socket before you press "Close Session" button
Connected successfully
Operation: Scan PartitionTable from Source (Vendor: Samsung)
Scanning soft partitions from LUN 0
GPT header is found
Stopped by User request...
Operation: Opening Firmware (Samsung)
Firmware: PICASSO3_EUR_OPEN.pit
LUN 0: The size of the "USERDATA" partition has been increased
LUN 3: The size of the "CPEFS" partition has been increased
Opening firmware completed
Operation: Adding firmware files (Samsung)
BL_G980FXXSCEUL7_G980FXXSCEUL7_SCL23182177_VCL2318 0807_MCL23346697_SQB47543609_VQB47543610_MQB475435 95_REV01_user_low_ship_MULTI_CERT.tar.md5
List of files in the firmware:
sboot.bin.lz4
up_param.bin.lz4
ldfw.img.lz4
tzsw.img.lz4
tzar.img.lz4
keystorage.bin.lz4
ssp.img.lz4
uh.bin.lz4
vbmeta.img.lz4
harx.bin.lz4
Operation: Writing by Vendor (Samsung)
Write/Erase check: Disabled
Unpacking files into: C:\Program Files\Z3X\EASYJTAGPLUS\Temp\
Unpacking : up_param.bin.lz4
Unpacking : up_param.bin
Unpacking : keystorage.bin.lz4
Unpacking : keystorage.bin
Unpacking : harx.bin.lz4
Unpacking : harx.bin
Unpacking : uh.bin.lz4
Unpacking : uh.bin
Unpacking : vbmeta.img.lz4
Unpacking : vbmeta.img
Unpacking : sboot.bin.lz4
Unpacking : sboot.bin
Unpacking : ldfw.img.lz4
Unpacking : ldfw.img
Unpacking : tzsw.img.lz4
Unpacking : tzsw.img
Unpacking : tzar.img.lz4
Unpacking : tzar.img
Unpacking : ssp.img.lz4
Unpacking : ssp.img
Unpacking done
Repartitioning ...
Rom: LUN 0, Part: PrimaryGPT, Address: 000000000000, Filename: From Memory
Rom: LUN 0, Part: BackupGPT, Address: 001DC97FB000, Filename: From Memory
Rom: LUN 3, Part: PrimaryGPT, Address: 000000000000, Filename: From Memory
Rom: LUN 3, Part: BackupGPT, Address: 0000007FB000, Filename: From Memory
Rom: LUN 0, Part: Pit, Address: 000000006000 |