Pandora cant flash properly this model OFP[Team Need to fix this issue]
i restore org nv first then i use sptool firmware read by other tool.
Phone running without any issue.
then repaired again but this time no issue , phone running well.
Quote:
Selected model: OPPO CPH2269 (Oppo A16)
Operation: Repair
Software version: 3.1
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x6CFC44F8, 0x5E397E77, 0x13E80B86, 0x16FE69A8
Get Chip ID... [MT6765]
Get SOC ID... [267032B773DC53FF57227DD6F6015256DE3E39B9930F487718 8DEC15BC31E9DC]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68423861503E0300422B5B68AF
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68423861503E0300422B5B68AF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6765
Board Platform : MT6765
Build ID : RP1A.200720.011
Build Date : Thu Aug 26 18:28:39 CST 2021
Display ID : RP1A.200720.011 release-keys
Security Patch : 2021-08-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1629972958632
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 8670
IMEI 2: 8670
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Save patched partiton... OK
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.
|
Quote:
Selected model: OPPO CPH2269 (Oppo A16)
Operation: Reboot to Recovery
Software version: 3.1
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Connect phone to BOX in BROM mode
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM20 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0766
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6765]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x6CFC44F8, 0x5E397E77, 0x13E80B86, 0x16FE69A8
Get Chip ID... [MT6765]
Get SOC ID... [267032B773DC53FF57227DD6F6015256DE3E39B9930F487718 8DEC15BC31E9DC]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [7]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
EMMC_ID: 0x90014A68423861503E0300422B5B68AF
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
EMMC INFO:
EMMC_ID : 0x90014A68423861503E0300422B5B68AF
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0001000000 (16.00Mb)
EMMC_USER : 0x0747C00000 (29.12Gb)
RAM INFO:
INT_SRAM: 0x000003A000 (232.00Kb)
EXT_RAM : 0x00C0000000 (3.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6765
Board Platform : MT6765
Build ID : RP1A.200720.011
Build Date : Thu Aug 26 18:28:39 CST 2021
Display ID : RP1A.200720.011 release-keys
Security Patch : 2021-08-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1629972958632
Prepare recovery boot done!
Power on device
|
