With Default SW Settings Same Error With me.
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.34
Load IDBase v312457 Ok!
Update configuration ...
Load IDBase v312457 Ok!
Operation : Reset Settings/Format FS [ v2.34 ]
Mode : SMART RESET
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port_V1632 (COM18)
MODE : BOOTROM
PORT : 18
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Cervino
TYPE : MODERN [RAPHAEL]
BROM : MEID : B714D404077887326898E34C121ACF7B
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 28E9A10509ECE53181FED0DA074EA25265CF96EEF94C70B5F6 E05157AC73A85F
BROM : SLA : Local Auth
BROM : SLA : Starting Auth
BROM : SLA : Auth Passed!
BROM : SEC : 0x000000E0
AGENT : 0_base : BASE_v2112 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMMC: CID : 13014E53304A3339441022988395C75D
EMMC: VEN : MICRON : OEM : 78 : ID : 53304A333944 : PRV : 0x10
EMMC: VEN : MICRON : S0J39D
EMMC: SNN : 580420501 ( 0x22988395 ) , MF : 12/2020
EMI : DEV : FireFly
EMI : SRC : preloader_k65v1_64_bsp.bin
EMI : CNT : 0009
EMI : Init EMI from INTERNAL DB
DA : SETUP EMI PARAMS FAILED!
ERROR : ABORT
Error : Fail to init protocol!
>>> Internal EMI : Select other EMI number! External Preloader - make sure it correct for connected device!
Reconnect Power/Cable!
Its Done with infinity FireFly after 2,3 tries.
Code:
Operation : Reset Settings/Format FS [ v2.34 ]
Mode : SMART RESET
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port_V1632 (COM18)
MODE : BOOTROM
PORT : 18
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Cervino
TYPE : MODERN [RAPHAEL]
BROM : MEID : B714D404077887326898E34C121ACF7B
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
BROM : SOCID : 28E9A10509ECE53181FED0DA074EA25265CF96EEF94C70B5F6E05157AC73A85F
BROM : Sending FireFly
FireFly : Starting ...
FireFly : Init Core
FireFly : Core init done!
FireFly : Running : v05.05.05 on MT6765
FireFly : eMMC init passed!
EMMC: CSD : D05F01328F5913FFFFFFFFEF964000A9
EMMC: CSD : TEMP_WRITE_PROTECT: False
EMMC: CSD : PERM_WRITE_PROTECT: False
EMMC: CID : 13014E53304A3339441022988395C75D
EMMC: VEN : MICRON : OEM : 78 : ID : 53304A333944 : PRV : 0x10
EMMC: VEN : MICRON : S0J39D
EMMC: SNN : 580420501 ( 0x22988395 ) , MF : 12/2020
EMMC: EXTCSD : rev1.8 ( eMMC 5.1 )
EMMC: EXTCSD [CONFIG] : 0x48, 0x02, 0x01
EMMC: EXTCSD [PARTITION_CONFIG] : 0x48
EMMC: EXTCSD [BOOT_BUS_WIDTH] : 0x02
EMMC: EXTCSD [RST_N_FUNCTION] : 0x01
EMMC: EXTCSD [PART_S_COMPLETED] : False
EMMC: EXTCSD [SIZE] : Market : 128 GB
EMMC: EXTCSD [SIZE] : Actual : 0x1D1F000000 [ 116.48 GB ]
EMMC: EXTCSD [EOL] : EOL status : Normal ( Less than 80% reserved blocks used )
EMMC: EXTCSD [EOL_A] : SLC status : 0% - 10% used
EMMC: EXTCSD [EOL_B] : MLC status : 0% - 10% used
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
USER : 0x1D1F000000 [ 116.48 GB ]
DA : USB : HIGH-SPEED
Boot done!
SmartInfo : 0x825657
Format Ok : RESET PROTECTION
Format Ok : USERDATA
Format Ok : CACHE
Format Ok : USERDATA
Format Ok : USERDATA
Done!
Elapsed: 00:01:30
Reconnect Power/Cable!