View Single Post
Old 08-22-2009, 21:02   #2 (permalink)
moulnisky
No Life Poster
 
moulnisky's Avatar
 
Join Date: Jan 2009
Location: England
Age: 59
Posts: 17,681
Member: 947561
Status: Offline
Thanks Meter: 14,053
First thing go in the post http://forum.gsmhosting.com/vbb/showthread.php?t=705358
and check if you have the last version of the software and of the firmware: if not just reinstall the suite and/or update the box.
How to move with cyclone working on BB5 mobiles
Connect the TX2 adapter to the box and the fbus cable to the TX2 adapter (The TX2 adapter is the yellow cable in bundle with the box)
Start always, once connected the mobile and started the module DCT4/WD2/BB5 reading the infos
If you can get the infos, OK; If you can't go in the tab BB5/Flash and click on check flashing bus (This will take the mobile in needed mode)
In the tab Common/Info click on read PM (This will give you a back-up of your full PM and will test if the connection of the Fbus cable is OK)
Go now in the tab BB5/security and Click on "create RPL from PHONE" (This will give you a plain RPL of the phone)
Now you have a complete back-up of your mobile
If you are going to do any job as downgrading or erase, better you click on "read certs". this will give you a complete back-up of all the mobile certificates.
Now have a check at your tools:
If you use the TMA cable standard (the one with the USB cable) go in the tab BB5/Flash and Thick where says "SKIP repower on BOOT"
If you are using TMA Evolution or you are working without any TMA "SKIP repower on BOOT" must be not thicked.
Go back in the BB5/security Tab.
SX4 bypass must be not thicked
Select which unlocking system you want use
a) PM308 recalculation or classic system
b) NCK calculation New method
c) NCK calculation Old methos
d) RPL system

Method A : PM308 recalculation
Use this system only for the mobile which can't be unlocked with any other system .
If the mobile is an old SL1 Thick where says "skip read SP Info", for the SL2 leave it not thicked
This system is able to rebuild the simlock table (using skip sp read thicked) in the rap3gv3 phones
Click on unlock
Job Done
Method B and C - NCK calculation
Just be sure you have a good local mode and press on unlock. If the procedure hangs after the codes are calculated just input them manually via keyboard.
Job Done

Method D - RPL system
Using this system we can unlock the mobiles which can't be unlocked via NCK and rebuild the simlock in the mobiles with SP data error. This system won't repair the superdongle
Just click on unlock and the job is done. The RPL is saved in the storedfiles folder anc can be used again if needed on the same mobile

Note: On the rapido SL2 with HASH 9A28 use only the the RPL system as the hash is a quite doggy

This is all

BR

Alex

FAQ about unlocking using the last update

Q:2nd. i have seen this 4 ways to unlock from now
- PM308 Recalculation (Standalone, Free)
- NCK Calculation (Standalone, Free, New Method)
- NCK Calculation (Standalone, Free, Old Method) Remark: Works only on SL2 Rapido Phones, SW < v30
- RPL Calculation (Server Based, Need Credits)the question is what option should we choose for what models
A: I would use as much I can the NCK calculation new metod; if it fails cause the hash (Sample 9A28) or other reason I would use the PM308 method or the RPL method

Q:3rd. for hash 9dd0 like 5220 what option of the four we have should choose
A:NCK calculation new method or RPL calculation method

Q:4rt for old sl1 phones like 5200, 6300, etc (rap3gv3) what option should we use
A:NCK calculation new method or RPL method

Q:5th for sl2 like 5310, 6120c, 6555, what option should we use
A:You can use almost all but the preferred ones are NCK new method and RPL method

Q:7th for rapido phones like n95 8gb what option
A:same of N. 5

Q:8th, for 5800 that version is lower than 30.00 that i just to direct unlock this phone without downgrade what option should i choose
A:NCK new method or RPL calculation

Q:9th for 5800 with version 30.xx 31xx what option and it cost some credits or not
A:RPL calculation - It is free and stand alone

Last edited by moulnisky; 10-03-2010 at 07:50.
 
The Following 83 Users Say Thank You to moulnisky For This Useful Post:
Show/Hide list of the thanked
 
Page generated in 0.09215 seconds with 7 queries