| WORKING !!!!!!!!!!
Establishing Connection with Box in Main Mode...
Handling device: [Cyclone Team], [Cyclone Box], [Platform: Classic]
Initializing box...
Box Firmware: Cyclone Main Application v02.20, (Aug 6 2013 20:34:19, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2012
Hardware Platform: Cyclone Key Flasher Interface (c) 2012 KarwosLabs
Box Serial Number: A000013A
HW Revision: E, Suitable for: Production, Case: Orange Key Casing, MCU Manufacture Time: Green PCB Rev. 4 2012 wk33, MCU 2011 wk09
Box is activated
Started box selftests procedure
All box selftests passed!
Super DCT4 Activation: TRUE
XGold/Blackberry Service Running, Counter: 100
Lumia No TP is ACTIVATED!
Avaiable Physical Memory: 3.1023GB
Avaiable Virtual Memory: 1.795GB
Avaiable Pagefile: 3.1023GB
Initializing FBUS...
All initialized - Ready to work
Lumia No TP Root Procedure Started...
If phone is alive, It will be automatically swithced to OSBL mode.
If software can't switch to OSBL mode, or phone is generally DEAD do folllowing:
1. Turn OFF device, wait 15 seconds afterwards
2. Eject USB cable, wait 10 seconds
3. Press and hold Volume-UP button
4. Insert USB Cable. OSBL should be booted.
Booting CMT...
[USB Composite Device]: WinUSB Port opened OK!
[USB Composite Device]: WinUSB Port opened OK!
[Nokia USB Connectivity]: WinUSB Port opened OK!
Switching to RAW Mode...
[Nokia USB Connectivity]: WinUSB Port opened OK!
[USB Composite Device]: WinUSB Port opened OK!
[Nokia USB Connectivity]: WinUSB Port opened OK!
Switching to RAW Mode...
[Nokia USB Connectivity]: WinUSB Port opened OK!
[Nokia USB Connectivity]: WinUSB Port opened OK!
OSBL Details
Protocol: v1.0
Version: v256.4
Build: 10
Timestamp: 9/29/2011 4:38:56 PM
OSBL Bootloader Ready
USB&UART Tracing set
RSA Signature Calculated for QCB Boot, Writing...
OSBL Certificate Details
Magic: WP70
Version: 0
Signer Server ID: 0x98031573
Signer Timestamp: 9/28/2011 4:52:12 PM
Signer S/N: 23
Signer User ID: 10046114
Auth Level: Care
Data Encryption: 0
Image Index: 0
Asic Index: 0
Type: Image Write
Hashtable Parsed OK
Certificate Accepted
[ASIC 0, Storage 4,1] Writing 850.552kB @ 0x000000000007D200
Write taken 0.437s (Average speed: 15944.20kBits/s)
Restoring Modem from BACKUP_RAMFS_IMAGE...
Restore OK
Restarting MCU...
Rooting Finished!
Looking for NAND disk...Done.
Trying to parse partition tables...Done.
----------------------------------------------------
FAT16 absolute address: 0x001F4200
FAT16 partition size: 0x0927C000
----------------------------------------------------
Reading FAT16 raw...Done.
Searching locations...Done.
Found 2 locations to modify, processing:
Reading sector 0...Done.
Modify sector...Done.
Updating sector...Done.
Reading sector 1...Done.
Modify sector...Done.
Updating sector...Done.
Modification written. Please follow those steps:
1. Disconnect USB cable and remove the battery
2. Insert not supported simcard and power on the phone
3. If asked for PIN code, enter 00000000
4. If asked for PUK code, enter 0000000000
5. After unlock success, connect to USB, enter OSBL mode
6. Press Unlock again to restore the phone to original
PHONE UNLOCKED !!!!!!!!!!!!! |