View Single Post
Old 08-28-2013, 14:20   #1 (permalink)
Waseem-y
Freak Poster
 
Join Date: Feb 2009
Location: Sabia >Gizan>KSA
Posts: 138
Member: 978854
Status: Offline
Sonork: 1582322
Thanks Meter: 29
need s3 i9300 dead boot steps

Hi easy jtag team

i have tried several times ..sevral s3 i9300 connect ok

here is log when i click on "Detect eMMC Card"

Successefuly connected to box on COM21
Box S/N: -------------, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1650 mV
CMD Active Level:2351 mV
EMMC CID 1501003030303030300020110726589D
EMMC CSD 902701320F5903FFF6DBFFEF8A404023
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 05/2005 FW rev.0x0 HW rev.0x0
EMMC Serial #: 537986854
EMMC NAME: 000000
EMMC Capacity: 16384 MB (High Density Card)
=============================================
Extended CSD rev 1.5 (MMC 4.41)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x03]:
implementation based on CMD12
Background operations support [BKOPS_SUPPORT: 0x01]
Background operations status [BKOPS_STATUS: 0x00]
TRIM Multiplier [TRIM_MULT: 0x01]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x15]
Secure Erase Multiplier [SEC_ERASE_MULT: 0x04]
Secure TRIM Multiplier [SEC_TRIM_MULT: 0x07]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x04]
Access size [ACC_SIZE: 0x08]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x90]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x13]
Sector Count [SEC_COUNT: 0x02000000]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x01]
Card Type [CARD_TYPE: 0x07]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x00]
Not boot enable
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x00]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
=============================================
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
=============================================
User area write protection register [USER_WP]: 0x00
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x01
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x05
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0xd38000
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00




and when i want to write boot file "EMMC_ROM2_00000000_00200000"
with selection
"Partition to access:>Boot<"
"Preset:>2mb<"

Start hex 0x000000
Lenth Hex 0x200000

Click on "Write eMMC Card"

selected this file downloaded from support "EMMC_ROM2_00000000_00200000"

here is log

Z3X Card Version : 22
Z3X Card Activation [JTAG] : 1
Resources ver. : MainRC ver.OCD040Z001 (C)2012 z3x-team.com
Writing file...H:\box seuup\z3x\EMMC_ROM2_2Mb_BOOT\EMMC_ROM2_00000000_00 200000.bin
Successefuly connected to box on COM21
Box S/N: 1616060D1E65C74C, ,FW Ver.: 01.47
Loading eMMC Addon Firmware...
CMD Pullup Level:1660 mV
CMD Active Level:2361 mV
EMMC CID 1501003030303030300020110726589D
EMMC CSD 902701320F5903FFF6DBFFEF8A404023
EMMC Manufactorer ID: 15
EMMC OEM ID: 0100
EMMC Date: 05/2005 FW rev.0x0 HW rev.0x0
EMMC Serial #: 537986854
EMMC NAME: 000000
EMMC Capacity: 16384 MB (High Density Card)
Writing 00200000 bytes to 00000000 ...ROM1
Write Speed: 364 kB/s
Done !!!

------------------------


still mobile is dead

what is solution

pls define steps


waiting or ur responce
  Reply With Quote
 
Page generated in 0.07557 seconds with 7 queries