LG H870 G6 FRP reset, Brick ? [Solved] Hi, I try to reset FRP via Octoplus Here is log Welcome to Octoplus FRP Tool v.1.5.9.0 Platform: LG Selected model: H870 Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Found phone on COM34 Reading info... Detected phone model: LG-H870 Mode: Emergency Initializing.. SW version: LGH870AT-00-V20h-260-06-NOV-26-2018+0 Android version: 8.0.0 Platform: msm8996 Reading partition... Reading BOOT... ID: 0005F0E100310000 Operation is not safe and exist risk to damage the device! Do You want to continue? Backup saved as LG_H870_22-01-2019_19-05-34.dump file Rebooting to Qualcomm 9008 mode... Searching for a phone. Please wait... "Qualcomm HS-USB QDLoader 9008" device not found. Please, don't disconnect cable, this can damage your device! Install "Qualcomm USB Driver" then press "Ok" button. After that phone goes to QUSB_BULK mode in Windows 10 Device Mannager and I tick CANCEL operation Operation was canceled Performed by 1.5.9.0 Software version. How to repair this piece of LG ? |
Hello. What is exact state of your phone, what device appear in Windows Device Manager, when You connect the phone to PC? |
Quote:
Device manager shows QUSB_BULK driver. that all |
same problem with my phone us997 detact as qualqum 9008 can i flash with h870 as this is only found |
@at-kom Please install Qualcomm USB Driver, then repeat the Reset FRP operation again, post here results. Quote:
|
@Xpress_banha Hello. Please post here full Software log of Reset FRP operation, we will check it. |
Quote:
I connect LG H870 to PC and automatic install drivers, Then Phone is installed: Qualcomm HS-USB QDLoader 9008 (COM37) on Windows Mannager. When I try to RESET FRP (Qualcomm 9008) with Octoplus FRP Tool I have : Platform: LG Selected model: H870 Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Connecting... Backup saved as LG_H870_24-01-2019_13-23-06.dump file Operation was failed! Performed by 1.5.9.0 Software version. |
Please, try to reboot your device via buttons, after repeat operation once again. |
Quote:
|
@at-kom Please contact us to Skype, we will check where can be the problem. Our contacts You can find in our profile. |
Please, try to do the next: 1. To reboot the phone, press and hold Vol- , Vol + and Power butto for about 10 sec. 2. Connect phone to PC, after repeat Reset FRP via 9008 mode again. 3. Then restore your device from the backup "LG_H870_22-01-2019_19-05-34.dump" 4. Post here full Software log. |
So It was my mistake, why ? To repair your phone U need backup (first time readed from phone in Octoplus FRP program) and. 1. In phone do the reset procedure : (Vol - ,Vol+ , Power Button , together, tick 15sec) then put USB TYPE C , cable to phone and connect it to Windows. Windows recognized : Qualcomm HS-USB QDloader 9008 (if not , you must uninstall driver from Windows, and install correct drivers QualcommUSBDriver.zip) 2.In FRP Octoplus Program , tick for backup file and use the first (largest) file. 3.Chose correct COM PORT in Octoplus FRP program tab 4.USE RESET FRP (QUALCOMM 9008) and do the reset procedure. here is my log : Welcome to Octoplus FRP Tool v.1.6.1.0 Platform: LG Selected model: H870 Opening "LG_H870_22-01-2019_19-05-34.dump"... Restore device from backup file? Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Connecting... Reading info... QC HW ID: 0005F0E100310000 QC CPU: Snapdragon 821 MSM8996AC Pro Searching loader... Sending loaders... Loader send successfuly. Reconnecting... Checking request.. Checking request.. Reading partition... Reading info... Brand: lge Model: LG-H870 Device: lucye Platform: msm8996 Android version: 8.0.0 Display ID: OPR1.170623.032 Restoring BOOT... Rebooting phone Backup saved as LG_H870_01-02-2019_08-01-24.dump file FRP lock is successfully reseted! Performed by 1.6.1.0 Software version. And now phone reset and work fine without google account . Thank to the best Octoplus TEAM Best regards TelfonGSM |
where are you loading the dump file for restore? I selected my dump file in the select software, then i select dump file, then i hit write firmware and get error. Platform: LG Selected model: H871 Put the phone into Download Mode: 1. Power phone OFF; 2. Press and hold "Vol+" button and connect USB cable. Searching for a phone. Please wait... No diagnostic ports found! Performed by 1.6.9.0 Software version. |
Did You follow the procedure correctly? 1. To reboot the phone, press and hold Vol- , Vol + and Power butto for about 10 sec. 2. Connect phone to PC, after repeat Reset FRP via 9008 mode again. 3. Then restore your device from the backup "LG_H870_22-01-2019_19-05-34.dump" 4. Post here full Software log. |
please help ..after octopus remove frp . phone dead Work ID: 00000000004B9F11 Platform: LG Selected model: US997 Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Connecting... Reading info... QC HW ID: 0005F0E100310000 QC CPU: Snapdragon 821 MSM8996AC Pro QC SW VER: 00000000 Searching loader... Sending loaders... Loader send successfuly. Reconnecting... Chip SN: 476C5206 Checking request.. Checking request.. Reading partition... Reading info... Brand: lge Model: LGUS997 Device: lucye Platform: msm8996 Android version: 8.0.0 Display ID: OPR1.170623.032 Firmware version: 190420940e75c Resetting FRP lock.. Searching for signatures... Rebooting phone Backup saved as lge_LGUS997_21-12-2020_08-55-58.dump file FRP lock is successfully reseted! Performed by 1.9.8.0 Software version. |
us997 dead after frp by octopus please help ..after octopus remove frp . phone dead Work ID: 00000000004B9F11 Platform: LG Selected model: US997 Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Connecting... Reading info... QC HW ID: 0005F0E100310000 QC CPU: Snapdragon 821 MSM8996AC Pro QC SW VER: 00000000 Searching loader... Sending loaders... Loader send successfuly. Reconnecting... Chip SN: 476C5206 Checking request.. Checking request.. Reading partition... Reading info... Brand: lge Model: LGUS997 Device: lucye Platform: msm8996 Android version: 8.0.0 Display ID: OPR1.170623.032 Firmware version: 190420940e75c Resetting FRP lock.. Searching for signatures... Rebooting phone Backup saved as lge_LGUS997_21-12-2020_08-55-58.dump file FRP lock is successfully reseted! Performed by 1.9.8.0 Software version. |
i try again mmay be it will work ... still on qualmcomm mode .. not coming up Work ID: 00000000004BA178 Platform: LG Selected model: US997 Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Connecting... Reading info... QC HW ID: 0005F0E100310000 QC CPU: Snapdragon 821 MSM8996AC Pro QC SW VER: 00000000 Searching loader... Sending loaders... Loader send successfuly. Reconnecting... Chip SN: 00004000 Checking request.. Checking request.. Reading partition... Reading info... Brand: lge Model: LGUS997 Device: lucye Platform: msm8996 Android version: 8.0.0 Display ID: OPR1.170623.032 Firmware version: 190420940e75c Resetting FRP lock.. Searching for signatures... FRP signature not found! Rebooting phone Backup saved as lge_LGUS997_21-12-2020_09-01-51.dump file Performed by 1.9.8.0 Software version. |
Hello. How did You manage to pur your device into Qualcomm Mode? |
sorry that was letter used to see if it will on back Log file "C:\PROGRA~1\Octoplus\OCTOPL~1\LOG\21-12-2020_16-33-14.log" created. 12/21/2020 4:33:19 PM > Searching for server... 12/21/2020 4:33:22 PM > Trying to ping server...12/21/2020 4:33:22 PM > ok 12/21/2020 4:33:22 PM > Trying connect to server... 12/21/2020 4:33:30 PM > Searching installed cards... 12/21/2020 4:33:30 PM > Found card with s/n: 0000584C 12/21/2020 4:33:30 PM > Server check... 12/21/2020 4:33:33 PM > Server Check succesfull! 12/21/2020 4:33:33 PM > Server Check succesfull! 12/21/2020 4:33:34 PM > Welcome to Octoplus/Octopus Box LG Software version 3.0.7.06 12/21/2020 4:33:34 PM > Card S/N : 000000584C 12/21/2020 4:34:13 PM > INI FUpdateInfo Done! 12/21/2020 4:34:13 PM > INI FShowUpdateInfo start 12/21/2020 4:34:13 PM > INI FShowUpdateInfo 2 12/21/2020 4:38:39 PM > -------------------------------------------------------------------------------- 12/21/2020 4:38:39 PM > Selected USB connection type 12/21/2020 4:38:41 PM > Transport: Connected 12/21/2020 4:38:44 PM > Authorized. 12/21/2020 4:38:48 PM > Work ID: 00000000004B7C69 12/21/2020 4:38:49 PM > Checking data...12/21/2020 4:38:50 PM > OK 12/21/2020 4:38:50 PM > Platform: LG MTK 12/21/2020 4:38:50 PM > Selected port: COM657 12/21/2020 4:38:50 PM > Selected baudrate: 0 12/21/2020 4:38:50 PM > Selected model: X120EMW 12/21/2020 4:38:50 PM > Please, disconnect cable, power phone OFF, connect P999 cable (with 910k resistor) 12/21/2020 4:38:50 PM > or 12/21/2020 4:38:50 PM > Power OFF phone, press and hold "Vol+" for 10 seconds and connect USB cable. 12/21/2020 4:39:21 PM > Phone found at port COM657 12/21/2020 4:39:21 PM > Mode: Emergency 12/21/2020 4:39:21 PM > Initializing flash...12/21/2020 4:39:23 PM > OK 12/21/2020 4:39:24 PM > Model ID: LGUS997 12/21/2020 4:39:24 PM > Incompatible model ID! 12/21/2020 4:39:30 PM > Canceled! 12/21/2020 4:39:30 PM > Performed by 3.0.7.06 Software version. 12/21/2020 4:39:30 PM > Elapsed Time: 12:00:50 AM 12/21/2020 4:40:48 PM > -------------------------------------------------------------------------------- 12/21/2020 4:40:51 PM > Can not connect. 12/21/2020 4:40:51 PM > Error: €Ñüì$í 12/21/2020 4:40:51 PM > Please, select Reset FRP Method! 12/21/2020 4:40:59 PM > Checking data...12/21/2020 4:41:00 PM > OK 12/21/2020 4:41:00 PM > Platform: LG Qualcomm 12/21/2020 4:41:00 PM > Selected port: COM657 12/21/2020 4:41:00 PM > Selected model: US997 12/21/2020 4:41:00 PM > Please, put the phone into download mode manually (Power phone OFF, press and hold "Vol+" button and connect the cable). 12/21/2020 4:41:00 PM > Reading info...12/21/2020 4:41:00 PM > Failed! 12/21/2020 4:41:00 PM > Port busy 12/21/2020 4:41:00 PM > Performed by 3.0.7.06 Software version. 12/21/2020 4:41:00 PM > Elapsed Time: 12:00:12 AM 12/21/2020 4:41:12 PM > -------------------------------------------------------------------------------- 12/21/2020 4:41:15 PM > Can not connect. 12/21/2020 4:41:15 PM > Error: °Ñüì$í 12/21/2020 4:41:15 PM > Please, select Reset FRP Method! 12/21/2020 4:41:17 PM > Checking data...12/21/2020 4:41:18 PM > OK 12/21/2020 4:41:18 PM > Platform: LG Qualcomm 12/21/2020 4:41:18 PM > Selected port: COM657 12/21/2020 4:41:18 PM > Selected model: US997 12/21/2020 4:41:18 PM > Please, put the phone into download mode manually (Power phone OFF, press and hold "Vol+" button and connect the cable). 12/21/2020 4:41:18 PM > Reading info... 12/21/2020 4:41:20 PM > Model ID: LGUS997 12/21/2020 4:41:20 PM > IMEI: 355274-08-052429-3 12/21/2020 4:41:20 PM > Android version: 8.0.0 12/21/2020 4:41:20 PM > Battery level: 7% 12/21/2020 4:41:21 PM > Mode: Emergency 12/21/2020 4:41:21 PM > Initializing flash...12/21/2020 4:41:22 PM > OK 12/21/2020 4:41:23 PM > Platform: msm8996 12/21/2020 4:41:23 PM > SW version: 12/21/2020 4:41:23 PM > US99721e_01 12/21/2020 4:41:23 PM > Android version: 8.0.0 12/21/2020 4:41:23 PM > LAF Version: 1.1 12/21/2020 4:41:23 PM > Product ID: PT02S170624000930 12/21/2020 4:41:23 PM > IMEI: 355274-08-052429-3 12/21/2020 4:41:23 PM > Target operator: NAO 12/21/2020 4:41:23 PM > Hardware: rev_10 12/21/2020 4:41:23 PM > Reading partitions...12/21/2020 4:41:30 PM > OK 12/21/2020 4:41:30 PM > Reading BOOT... 12/21/2020 4:41:30 PM > ID: 0005F0E100310000 12/21/2020 4:41:30 PM > Operation is not safe and exist risk to damage the device! Do You want to continue?12/21/2020 4:41:36 PM > OK 12/21/2020 4:41:37 PM > Backup saved to "US997_355274080524293_21-12-2020_16-41-36.oct" 12/21/2020 4:41:37 PM > Switching to Qualcomm 9008 mode... 12/21/2020 4:41:42 PM > Found port COM43 12/21/2020 4:41:42 PM > Connecting...12/21/2020 4:41:43 PM > OK 12/21/2020 4:41:43 PM > Sending loader...12/21/2020 4:42:07 PM > OK 12/21/2020 4:42:07 PM > Reconnecting phone...12/21/2020 4:42:08 PM > OK 12/21/2020 4:42:10 PM > Checking request... 12/21/2020 4:42:10 PM > Request has been successfully sent! 12/21/2020 4:42:10 PM > Obtaining response...12/21/2020 4:42:10 PM > OK 12/21/2020 4:42:11 PM > Reading partitions... 12/21/2020 4:42:11 PM > Sent 0 / 163 12/21/2020 4:42:11 PM > Sent 0 / 163 12/21/2020 4:42:11 PM > Sent 0 / 163 12/21/2020 4:42:11 PM > Sent 0 / 163 12/21/2020 4:42:12 PM > Sent 0 / 16312/21/2020 4:42:12 PM > Failed! 12/21/2020 4:42:12 PM > Rebooting phone... 12/21/2020 4:42:12 PM > Sent 0 / 96 12/21/2020 4:42:12 PM > Sent 0 / 96 12/21/2020 4:42:12 PM > Sent 0 / 96 12/21/2020 4:42:12 PM > Sent 0 / 96 12/21/2020 4:42:12 PM > Sent 0 / 96 12/21/2020 4:42:12 PM > Performed by 3.0.7.06 Software version. 12/21/2020 4:42:12 PM > Elapsed Time: 12:01:00 AM 12/21/2020 4:43:19 PM > -------------------------------------------------------------------------------- 12/21/2020 4:43:22 PM > Can not connect. 12/21/2020 4:43:22 PM > Error: @‚Ñ<ídí 12/21/2020 4:43:22 PM > Please, select Reset FRP Method! 12/21/2020 4:43:23 PM > To perform Reset FRP operation do the next: 1. Attach testpoint as shown on Figure in manual, and connect phone with Micro USB cable. 2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008". 3. Release testpoint. 12/21/2020 4:43:23 PM > Found port COM43 12/21/2020 4:43:23 PM > Connecting...12/21/2020 4:43:24 PM > Failed! 12/21/2020 4:43:24 PM > Performed by 3.0.7.06 Software version. 12/21/2020 4:43:24 PM > Elapsed Time: 12:00:05 AM 12/21/2020 4:44:36 PM > -------------------------------------------------------------------------------- 12/21/2020 4:44:39 PM > Transport: Connected 12/21/2020 4:44:44 PM > Authorized. 12/21/2020 4:44:53 PM > Work ID: 00000000004B7F72 12/21/2020 4:44:54 PM > Please, select Reset FRP Method! 12/21/2020 4:44:56 PM > To perform Reset FRP operation do the next: 1. Attach testpoint as shown on Figure in manual, and connect phone with Micro USB cable. 2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008". 3. Release testpoint. 12/21/2020 4:45:36 PM > Performed by 3.0.7.06 Software version. 12/21/2020 4:45:36 PM > Elapsed Time: 12:01:00 AM |
thanks problem solve by restoring the backup file Welcome to Octoplus/Octopus Box LG Software version 3.0.7.06 Card S/N : 000000584C -------------------------------------------------------------------------------- Work ID: 00000000004CAEF1 Please, select Reset FRP Method! Opening "US997_355274080524293_21-12-2020_16-41- 36.oct"... Restore device from backup file? Please, connect the phone... Found port COM647 Connecting...Failed! Performed by 3.0.7.06 Software version. -------------------------------------------------------------------------------- Work ID: 00000000004CAF6A Please, select Reset FRP Method! Opening "US997_355274080524293_21-12-2020_16-41- 36.oct"... Restore device from backup file? Please, connect the phone... Found port COM43 Connecting...OK Sending loader...Failed! Resource not found : QCOM_9008 QMSM8996 Rebooting phone... Performed by 3.0.7.06 Software version. -------------------------------------------------------------------------------- Work ID: 00000000004CB018 Please, select Reset FRP Method! Opening "US997_355274080524293_21-12-2020_16-41- 36.oct"... Restore device from backup file? Please, connect the phone... Found port COM43 Connecting...OK Sending loader...Failed! Rebooting phone... Performed by 3.0.7.06 Software version. -------------------------------------------------------------------------------- Work ID: 00000000004CB06F Please, select Reset FRP Method! Opening "US997_355274080524293_21-12-2020_16-41- 36.oct"... Restore device from backup file? Please, connect the phone... Found port COM43 Connecting...OK Sending loader...Failed! Rebooting phone... Sent 0 / 96 Sent 0 / 96 Sent 0 / 96 Sent 0 / 96 Sent 0 / 96 Performed by 3.0.7.06 Software version. -------------------------------------------------------------------------------- Work ID: 00000000004CB0BC Please, select Reset FRP Method! Opening "US997_355274080524293_21-12-2020_16-41- 36.oct"... Restore device from backup file? Please, connect the phone... Found port COM43 Connecting...OK Sending loader...OK Reconnecting phone...OK Checking request... Request has been successfully sent! Obtaining response...OK Reading partitions...OK Restoring BOOT...OK Rebooting phone... Performed by 3.0.7.06 Software version. |
Hi. I have same problem. Drivers seem ok and reset FRP is working fine in Qualcomm mode just i can't get out phone from qualcomm mode to write backup. Please if have any idea to get it back to live. Thank you. Work ID: 0000000000A7E24D Platform: LG Selected model: H870 Put the phone into EDL mode: 1. Attach testpoint as shown in Help manual; 2. Connect USB cable; 3. Release testpoint after 3-5 seconds. Searching for a phone. Please wait... Connecting... Reading info... QC HW ID: 0005F0E100310000 QC CPU: Snapdragon 821 MSM8996AC Pro QC SW VER: 00000000 Searching loader... Sending loaders... Loader send successfuly. Reconnecting... Chip SN: BC2E0000 Checking request.. Checking request.. Reading partition... Reading info... Brand: lge Model: LG-H870 Device: lucye Platform: msm8996 Android version: 8.0.0 Display ID: OPR1.170623.032 Firmware version: 190992024f88a Resetting FRP lock.. Searching for signatures... FRP signature not found! Rebooting phone Backup saved as lge_LG-H870_28-02-2021_20-10-10.dump file Performed by 1.9.9.2 Software version. |
Finally solved thank you. Seem oldest backup wasn't good for boot restore so software didn't ask at reset frp by qualcomm operation if i want to restore boot. After choose second oldest backup software asked about boot restore option and did it fine after i selected yes. Thank you again. |
Welcome to Octoplus/Octopus Box LG Software version 3.1.3 Card S/N : 0001039664 -------------------------------------------------------------------------------- Work ID: 000000000121D679 Please, select Reset FRP Method! Opening "H870DS_356145083071954_15-06-2021_14-35- 06.oct"... Restore device from backup file? Please, connect the phone... Found port COM10 Connecting...OK Sending loader...OK Reconnecting phone...OK Checking request... Request has been successfully sent! Obtaining response...OK Reading partitions...OK Restoring BOOT...OK Rebooting phone... Performed by 3.1.3 Software version. -------------------------------------------------------------------------------- Work ID: 000000000121D77F Please, select Reset FRP Method! Opening "H870DS_356145083071954_15-06-2021_14-35- 06.oct"... Restore device from backup file? To perform Reset FRP operation do the next: 1. Attach testpoint as shown on Figure in manual, and connect phone with Micro USB cable. 2. Check PC Device Manager, a new device should appear "Qualcomm HS-USB QDLoader 9008". 3. Release testpoint. Found port COM10 Connecting...OK Sending loader...OK Reconnecting phone...OK Checking request... Request has been successfully sent! Obtaining response...OK Reading partitions...OK Searching signatures... Step 1... Step 2... Step 3... Resetting FRP Lock...OK Resetting FRP lock successfully completed! Rebooting phone... Performed by 3.1.3 Software version. thansk done. |
All times are GMT +1. The time now is 23:39. |
vBulletin Optimisation provided by
vB Optimise (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -