🐙 Post here success Reset FRP story with Octoplus FRP Tool - Page 39 - GSM-Forum

windowshu · 04-27-2018, 13:58

Platform: MOTOROLA
Selected model: XT1767
Put the phone into Factory Mode:
1. Power phone OFF;
2. Press and hold "Vol-" + "Power" buttons;
3. Select Factory Mode, then confirm your selection;
4. Wait until the phone Power ON;
5. Connect USB cable.
Searching for a phone. Please wait...
Phone found.
Reading info...
Phone model: 8937.gen:
Firmware released date: Jun 10 2017
Firmware released time: 22:44:46
Firmware compiled date: Jun 08 2017
Firmware compiled time: 23:00:00
SW version: MPSS.JO.3.0-00269-8937_GENNS_PACK-1.95745.3.102706.1
Enabling "USB Debugging" mode...
Put the phone in Factory Mode:
1. Disconnect USB cable;
2. Power OFF the phone;
3. Press "Vol-" and "Power" buttons;
4. Select Factory Mode then confirm your selection;
5. Wait until phone is power ON and connect USB Cable;
6. Install necesarry drivers then press "OK" button
Please, press "OK" button on the phone to allow USB debugging..
Searching for a phone (waiting for ADB device)...
Phone found.
Reading info...
Phone model: motorola Moto E (4)
SW version: NDQS26.69-23-2-3
Date: Fri Sep 22 00:54:33 CDT 2017
Android version: 7.1.1
Baseband M8917_16000.269.04.03.01R PERRY_NA_CUST
Detected phone model: XT1767
Resetting FRP lock..
FRP lock is successfully reseted!
Performed by 1.2.4.0 Software version.

maxpatri9 · 04-27-2018, 16:01

SEL

SELECT N920P USING UFS METHOT
Welcome to Octoplus FRP Tool v.1.2.4
Platform: SAMSUNG
Selected model: SM-N920P
To put SM-N920P into Download Mode, You have to perform the following steps:
1. Reconnect the battery.
2. Press and hold "Volume-" + "Home" + "Power ON" keys.
3. When phone turns on, press "Volume+" key.
Searching for a phone. Please wait...
Phone found.
Initializing..
PIT was read successfully.
Searching for UART interface.. COM48
Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds
Searching for device. Please wait...
Resetting FRP lock..
FRP lock is successfully reseted!
Wait 3-4 min then goto "Menu -> Settings -> Backup and reset" and make "Factory data reset"
Performed by 1.2.4.0 Software version.

Platform: SAMSUNG
Selected model: SM-N920P
ADB server killed.
Please, press "OK" button on the phone to allow USB debugging..
Warning: Selected model (SM-N920P) differs from the detected one (SM-N920R4)!
If you want select (SM-N920R4) as (SM-N920P) model, please check "manual select".
Operation was failed!
Performed by 1.2.4.0 Software version.

Platform: SAMSUNG
Selected model: SM-N920P
Selected port: COM1
Detected phone model: SM-N920R4
Firmware compiled date: Thu Jun 15 15:01:41 KST 2017
PDA version: N920R4TYU3CQF2
CSC version: N920R4USC3CQF2
SW version: N920R4TYU3CQF2
Phone SN: 00000000000
Android version: 7.0 (NRD90M)
Sales code: USC
Country: USA
HW platform: exynos5
HW Chip: exynos7420
HW Modem: MDM9635M
Security patch level: 2017-06-01
Codename: noblelteusc
Performed by 1.2.4.0 Software version.

SAHILAKRAM · 04-28-2018, 08:30

THANKS --OCTOPLUS TEAM
Welcome to Octoplus FRP Tool v.1.2.4
Platform: LG
Selected model: MS210
Put the phone into Download Mode:
1. Power phone OFF;
2. Press and hold "Vol+" button and connect USB cable.
Searching for a phone. Please wait...
Found phone on COM784
Reading info...
Detected phone model: LGMS210
Warning: Selected model (MS210) differs from the detected one (LGMS210)!
Mode: Emergency
Initializing..
SW version: LGMS210AT-00-V10t-MPCS-US-NOV-14-2017-ARB00+0
Android version: 7.0
Reset FRP operation for MS210 will delete all user data on the phone (contacts, pictures and others)!
Do You want to continue?
Reading partition...
Detecting writing method...
Trying to repeat..
Trying third method...
Resetting FRP lock..
Writing loader...
Writing userdata...
Formating encrypt section
Restoring loader...
Perform factory reset to complete operation!
FRP lock is successfully reseted!
Performed by 1.2.4.0 Software version.
Report Post

pintu_das · 04-28-2018, 08:54

Huawei Y9 2018 Dual SIM FLA-LX2 FRP lock is successfully reseted!

Quote:

Welcome to Octoplus FRP Tool v.1.2.4
Platform: HUAWEI
Selected model: FLA-LX2
Put the phone in FastBoot Mode:
1. Remove SD and SIM cards from the phone
2. Power phone OFF
3. Press and hold "Vol-" and insert USB cable
4. Wait until the phone enter in FastBoot Mode
Searching for a phone. Please wait...
Detected phone model: FLA-LX2
Phone SN: HXT7N18321007813
Phone IMEI: 867419032967618
Phone IMEI2: 867419032997623
SW version: FLA-LX2 8.0.0.120(C636)
Connecting to server..OK
Authorizing...OK
Resetting FRP lock..
If the device didn't reboot automatically, try to reconnect USB cable or re-boot it manually.
FRP lock is successfully reseted!
Performed by 1.2.4.0 Software version.

Thanks Octopus box

kaka16dz · 04-28-2018, 15:48

LG K7 X210DS Reset FRP successfully done:

Welcome to Octoplus FRP Tool v.1.2.3
Platform: LG
Selected model: X210DS
Please, power phone OFF and connect USB cable.
Searching for a phone. Please wait...
Found phone on COM238
Detecting Chip Version...
HW Chip: MT6580: 6580.0000
HW Version: 8A00.CA00.0000.0000
Connecting...
Brom Version: FF
BootLoader Version: 01
Searching Download Agent...
Selected DA: MTK_AllInOne_DA_Octoplus_v1.1, n.0
Sending Download Agent...
DA sent successfully
Initializing DA...
Synchronizing with DA...
NAND Flash: not installed
eMMC Flash: .15010051.3732534D.4200D0B7.D3544359
eMMC Flash: Samsung: Q72SMB
DA ver: 4.2.94
Initializing Memory Flash..
Initialization successfully completed
Sending loaders...
Loader send successfuly.
Reading Flash Info...
EMMC rpmb size: 0 Mb
EMMC boot1 size: 4 Mb
EMMC boot2 size: 4 Mb
EMMC gp1 size: 0 Mb
EMMC gp2 size: 0 Mb
EMMC gp3 size: 0 Mb
EMMC gp4 size: 0 Mb
EMMC user area size: 7456 Mb
Internal RAM size: 128 Kb
External RAM size: 1024 Mb
Reading partition...
Reading info...
Brand: lge
Model: LG-X210
Device: m13g
Platform: mt6580
Android version: 5.1
Searching for signatures...
Resetting FRP lock..
FRP lock is successfully reseted!
Backup saved as LG_X210DS_28-04-2018_16-43-32.dump file
Performed by 1.2.3.0 Software version.

pintu_das · 04-29-2018, 12:30

Huawei Y7 Prime Dual SIM 32GB TRT-L21A FRP lock is successfully reseted!

Put the phone in FastBoot Mode:
1. Remove SD and SIM cards from the phone
2. Power phone OFF
3. Press and hold "Vol-" and insert USB cable
4. Wait until the phone enter in FastBoot Mode

Welcome to Octoplus FRP Tool v.1.2.4
Platform: HUAWEI
Selected model: TRT-L21A
Put the phone in FastBoot Mode:
1. Remove SD and SIM cards from the phone
2. Power phone OFF
3. Press and hold "Vol-" and insert USB cable
4. Wait until the phone enter in FastBoot Mode
Searching for a phone. Please wait...
Detected phone model: TRT-L21A
Phone SN: VWD7N17818009441
Phone IMEI: 864753036740081
Connecting to server..OK
Authorizing...OK
Resetting FRP lock..
If the device didn't reboot automatically, try to reconnect USB cable or re-boot it manually.
FRP lock is successfully reseted!
Performed by 1.2.4.0 Software version.

THANKS OCTOPUS TEAM

patosky2012 · 04-29-2018, 18:09

zte ftm mode press vol- and conecct usb cable
Log file "C:\Program Files\Octoplus\Octoplus_FRP_Tool\LOG\29-04-2018_10-59-37.log" created (4/29/2018 10:59:39 AM).
INFO : 4/29/2018 11:00:12 AM > Welcome to Octoplus FRP Tool v.1.2.4
INFO : 4/29/2018 11:00:46 AM > Platform: ZTE
INFO : 4/29/2018 11:00:46 AM > Selected model: Z982
WARN : 4/29/2018 11:00:46 AM > Put the phone into Factory mode:
WARN : 4/29/2018 11:00:46 AM > 1. Power phone OFF;
WARN : 4/29/2018 11:00:46 AM > 2. Press and hold "Vol-" button and connect USB cable.
INFO : 4/29/2018 11:00:46 AM > Searching for a phone. Please wait...
INFO : 4/29/2018 11:00:49 AM > Found phone on COM10
INFO : 4/29/2018 11:00:49 AM > Mode: Diagnostic
INFO : 4/29/2018 11:00:49 AM > Firmware released date: Jul 19 2017
INFO : 4/29/2018 11:00:49 AM > Firmware released time: 12:14:58
INFO : 4/29/2018 11:00:49 AM > Firmware compiled date: Jun 21 2017
INFO : 4/29/2018 11:00:49 AM > Firmware compiled time: 03:00:00
INFO : 4/29/2018 11:00:49 AM > SW version: MPSS.TA.2.3.c1-00361-8953_GEN_PACK-1.103191.1.104438.1
INFO : 4/29/2018 11:00:49 AM > Rebooting to Qualcomm 9008 mode...
INFO : 4/29/2018 11:00:52 AM > Found phone on COM11
INFO : 4/29/2018 11:00:52 AM > Mode: Qualcomm 9008
INFO : 4/29/2018 11:00:52 AM > Connecting...
INFO : 4/29/2018 11:00:52 AM > Sending loaders...
INFO : 4/29/2018 11:01:13 AM > Loader send successfuly.
INFO : 4/29/2018 11:01:13 AM > Reconnecting...
INFO : 4/29/2018 11:01:15 AM > Checking request..
INFO : 4/29/2018 11:01:16 AM > Reading partition...
INFO : 4/29/2018 11:01:17 AM > Reading info...
INFO : 4/29/2018 11:01:18 AM > Brand: ZTE
INFO : 4/29/2018 11:01:18 AM > Model: Z982
INFO : 4/29/2018 11:01:18 AM > Device: crocus
INFO : 4/29/2018 11:01:18 AM > Platform: msm8937
INFO : 4/29/2018 11:01:18 AM > Android version: 7.1.1
INFO : 4/29/2018 11:01:18 AM > Display ID: Z982_MPCSV1.0.0B14
INFO : 4/29/2018 11:01:18 AM > Searching for signatures...
INFO : 4/29/2018 11:01:18 AM > Resetting FRP lock..
WARN : 4/29/2018 11:01:19 AM > FRP lock is successfully reseted!
INFO : 4/29/2018 11:01:20 AM > Rebooting phone
INFO : 4/29/2018 11:01:22 AM > Backup saved as ZTE_Z982_29-04-2018_11-01-16.dump file
INFO : 4/29/2018 11:01:22 AM > Performed by 1.2.4.0 Software version.
INFO : 4/29/2018 11:01:22 AM >

jseyedanas · 04-30-2018, 00:07

Model: HISENCE C1
FRP REMOVE SUCESSFUL

Platform: _GENERAL RESET FRP METHODS
Selected model: ADB METHOD
Searching for a phone (waiting for ADB device)...
Please, press "OK" button on the phone to allow USB debugging..
Phone found.
Reading info...
Phone model: Hisense Hisense C1
SW version: LMY47V
Date: 2016年 12月 26日星期一 11:27:09 CST
Android version: 5.1.1
Baseband M8936FAAAANUZM-1.37561.1.38671.1
Resetting FRP lock..
FRP lock is successfully reseted!
Performed by 1.2.3.0 Software version.

jseyedanas · 04-30-2018, 00:08

Model: Wiko Jerry 2
FRP REMOVE SUCESSFUL

Platform: WIKO
Selected model: JERRY 2
Please, power phone OFF and connect USB cable.
Searching for a phone. Please wait...
Found phone on COM37
Detecting Chip Version...
HW Chip: MT6580: 6580.0000
HW Version: 8A00.CA00.0000.0000
Connecting...
Brom Version: FF
BootLoader Version: 01
Searching Download Agent...
Selected DA: MTK_AllInOne_DA_Octoplus_v1.0_PL, n.1
Sending Download Agent...
DA sent successfully
Initializing DA...
Synchronizing with DA...
NAND Flash: not installed
eMMC Flash: .15010046.4536324D.420329A8.F2EFA471
eMMC Flash: Samsung: FE62MB
DA ver: 4.2.9C
Initializing Memory Flash..
Initialization successfully completed
Sending loaders...
Loader send successfuly.
Reading Flash Info...
EMMC rpmb size: 4 Mb
EMMC boot1 size: 4 Mb
EMMC boot2 size: 4 Mb
EMMC gp1 size: 0 Mb
EMMC gp2 size: 0 Mb
EMMC gp3 size: 0 Mb
EMMC gp4 size: 0 Mb
EMMC user area size: 14910 Mb
Internal RAM size: 128 Kb
External RAM size: 1024 Mb
Reading partition...
Reading info...
Brand: WIKO
Model: JERRY2
Device: v2610
Platform: mt6580
Android version: 7.0
Display ID: alps-mp-n0.mp2-V1_tinno6580.we.n_P136
Searching for signatures...
Resetting FRP lock..
FRP lock is successfully reseted!
Backup saved as WIKO_JERRY 2_29-04-2018_23-56-53.dump file
Performed by 1.2.3.0 Software version

pintu_das · 04-30-2018, 05:57

Huawei P9 Lite VNS-L21 2GB RAM FRP lock is successfully reseted!

Put the phone in FastBoot Mode:
1. Remove SD and SIM cards from the phone
2. Power phone OFF
3. Press and hold "Vol-" and insert USB cable
4. Wait until the phone enter in FastBoot Mode

Welcome to Octoplus FRP Tool v.1.2.4
Platform: HUAWEI
Selected model: VNS-L21
Put the phone in FastBoot Mode:
1. Remove SD and SIM cards from the phone
2. Power phone OFF
3. Press and hold "Vol-" and insert USB cable
4. Wait until the phone enter in FastBoot Mode
Searching for a phone. Please wait...
Detected phone model: VNS-L21
Phone SN: BUC4C16826007091
Phone IMEI: 862264035999811
Phone IMEI: 862264036039823
SW version: VNS-L21C185B360
Connecting to server..OK
Authorizing...OK
Resetting FRP lock..
If the device didn't reboot automatically, try to reconnect USB cable or re-boot it manually.
FRP lock is successfully reseted!
Performed by 1.2.4.0 Software version.

onz · 04-30-2018, 10:42

Smart144 · 04-30-2018, 11:05

mmurugan1978 · 04-30-2018, 12:39

Platform: ASUS
Selected model: ZC521TL (X00GD)
Please, power phone OFF, press and hold "Vol-" button and connect USB cable.
Searching for a phone. Please wait...
Found phone on COM3
Detecting Chip Version...
HW Chip: MT6755: 0326.0000
HW Version: 8A00.CB00.0001.0000
HW Chip: MT6750: 00000442
Connecting...
Brom Version: 05
BootLoader Version: FE
Sending auth...
Searching Download Agent...
Selected DA: MTK_AllInOne_DA_Octoplus_v1.0_PL, n.0
Sending Download Agent...
DA sent successfully
Initializing DA...
Synchronizing with DA...
Mobile Status: SYNC
DA ver: 2099.3.3
Mobile Status: brom
Sending BootLoader Info...
Initializing Memory Flash..
Initialization successfully completed
Sending loaders...
Mobile Status: SYNC
Reading Flash Info...
EMMC rpmb size: 4 Mb
EMMC boot1 size: 4 Mb
EMMC boot2 size: 4 Mb
EMMC gp1 size: 0 Mb
EMMC gp2 size: 0 Mb
EMMC gp3 size: 0 Mb
EMMC gp4 size: 0 Mb
EMMC user area size: 29820 Mb
eMMC Flash: .13014E51.334A3937.56100317.8E60B3B1
eMMC Flash: Unknown: Q3J97V
Internal RAM size: 256 Kb
External RAM size: 3072 Mb
Reading partition...
Reading info...
Brand: asus
Model: ASUS_X00GD
Device: ASUS_X00G_1
Platform: mt6750
Android version: 7.0
Display ID: IN_Phone-14.02.1801.29-20180125
Searching for signatures...
Resetting FRP lock..
FRP lock is successfully reseted!

Dr_Wolodya · 04-30-2018, 13:18

Reset FRP on Samsung SM-G531H successfully done:

Code:

Welcome to Octoplus FRP Tool v.1.2.4
Platform: SAMSUNG
Selected model: SM-G531H
To put SM-G531H into Download Mode, You have to perform the following steps:
1. Reconnect the battery.
2. Press and hold "Volume-" + "Home" + "Power ON" keys.
3. When phone turns on, press "Volume+" key.
Searching for a phone. Please wait...
Phone found.
Initializing..
Resetting FRP lock..success
Resetting EE lock..success
Resetting Samsung Account lock..not supported
FRP lock is successfully reseted!
Performed by 1.2.4.0 Software version.

Surtax · 04-30-2018, 13:34

Welcome to Octoplus FRP Tool v.1.2.4
Platform: HUAWEI
Selected model: LUA-U22
Please, power phone OFF and connect USB cable.
Searching for a phone. Please wait...
Found phone on COM53
Detecting Chip Version...
HW Chip: MT6582: 6582.0000
HW Version: 8A00.CA01.0001.0000
Connecting...
Brom Version: FF
BootLoader Version: 01
Searching Download Agent...
Selected DA: MTK_AllInOne_DA_Octoplus_v1.1, n.2
Sending Download Agent...
DA sent successfully
Initializing DA...
Synchronizing with DA...
NAND Flash: not installed
eMMC Flash: .90014A48.38473165.05075417.14AC5345
eMMC Flash: Hynix: H8G1e
DA ver: 4.2.87
Initializing Memory Flash..
Initialization successfully completed
Sending loaders...
Loader send successfuly.
Reading Flash Info...
EMMC rpmb size: 4 Mb
EMMC boot1 size: 4 Mb
EMMC boot2 size: 4 Mb
EMMC gp1 size: 0 Mb
EMMC gp2 size: 0 Mb
EMMC gp3 size: 0 Mb
EMMC gp4 size: 0 Mb
EMMC user area size: 7456 Mb
Internal RAM size: 128 Kb
External RAM size: 1024 Mb
Reading partition...
Reading partition...
Reading info...
Brand: HUAWEI
Model: HUAWEI LUA-U22
Device: HWLUA-U6582
Platform: mt6582
Android version: 5.1
Display ID: LUA-U22C479B006
Searching for signatures...
Resetting FRP lock..
FRP lock is successfully reseted!
Backup saved as HUAWEI_LUA-U22_30-04-2018_15-09-10.dump file
Performed by 1.2.4.0 Software version.

Thanks Octopus Team!!!

04-27-2018, 13:58	#571 (permalink)
windowshu No Life Poster Join Date: Sep 2006 Location: Cuba Posts: 871 Member: 346150 Status: Offline Sonork: 100.1661091 Thanks Meter: 536	🐙 Report FRP Motorola XT1767 OK Platform: MOTOROLA Selected model: XT1767 Put the phone into Factory Mode: 1. Power phone OFF; 2. Press and hold "Vol-" + "Power" buttons; 3. Select Factory Mode, then confirm your selection; 4. Wait until the phone Power ON; 5. Connect USB cable. Searching for a phone. Please wait... Phone found. Reading info... Phone model: 8937.gen: Firmware released date: Jun 10 2017 Firmware released time: 22:44:46 Firmware compiled date: Jun 08 2017 Firmware compiled time: 23:00:00 SW version: MPSS.JO.3.0-00269-8937_GENNS_PACK-1.95745.3.102706.1 Enabling "USB Debugging" mode... Put the phone in Factory Mode: 1. Disconnect USB cable; 2. Power OFF the phone; 3. Press "Vol-" and "Power" buttons; 4. Select Factory Mode then confirm your selection; 5. Wait until phone is power ON and connect USB Cable; 6. Install necesarry drivers then press "OK" button Please, press "OK" button on the phone to allow USB debugging.. Searching for a phone (waiting for ADB device)... Phone found. Reading info... Phone model: motorola Moto E (4) SW version: NDQS26.69-23-2-3 Date: Fri Sep 22 00:54:33 CDT 2017 Android version: 7.1.1 Baseband M8917_16000.269.04.03.01R PERRY_NA_CUST Detected phone model: XT1767 Resetting FRP lock.. FRP lock is successfully reseted! Performed by 1.2.4.0 Software version. Last edited by Octopus box; 04-27-2018 at 14:35.

04-27-2018, 16:01	#572 (permalink)
maxpatri9 No Life Poster Join Date: Apr 2015 Location: Dominican Republic Posts: 2,564 Member: 2382052 Status: Offline Thanks Meter: 1,511	🐙 Samsung SM-N920R4 Reset FRP successfully done SEL SELECT N920P USING UFS METHOT Welcome to Octoplus FRP Tool v.1.2.4 Platform: SAMSUNG Selected model: SM-N920P To put SM-N920P into Download Mode, You have to perform the following steps: 1. Reconnect the battery. 2. Press and hold "Volume-" + "Home" + "Power ON" keys. 3. When phone turns on, press "Volume+" key. Searching for a phone. Please wait... Phone found. Initializing.. PIT was read successfully. Searching for UART interface.. COM48 Connect Samsung Micro UART cable(with 525K resistor), press and hold "Vol-" + "Power" buttons for 15-20 seconds Searching for device. Please wait... Resetting FRP lock.. FRP lock is successfully reseted! Wait 3-4 min then goto "Menu -> Settings -> Backup and reset" and make "Factory data reset" Performed by 1.2.4.0 Software version. Platform: SAMSUNG Selected model: SM-N920P ADB server killed. Please, press "OK" button on the phone to allow USB debugging.. Warning: Selected model (SM-N920P) differs from the detected one (SM-N920R4)! If you want select (SM-N920R4) as (SM-N920P) model, please check "manual select". Operation was failed! Performed by 1.2.4.0 Software version. Platform: SAMSUNG Selected model: SM-N920P Selected port: COM1 Detected phone model: SM-N920R4 Firmware compiled date: Thu Jun 15 15:01:41 KST 2017 PDA version: N920R4TYU3CQF2 CSC version: N920R4USC3CQF2 SW version: N920R4TYU3CQF2 Phone SN: 00000000000 Android version: 7.0 (NRD90M) Sales code: USC Country: USA HW platform: exynos5 HW Chip: exynos7420 HW Modem: MDM9635M Security patch level: 2017-06-01 Codename: noblelteusc Performed by 1.2.4.0 Software version.

04-28-2018, 08:30	#573 (permalink)
SAHILAKRAM Insane Poster Join Date: Apr 2016 Location: india Posts: 94 Member: 2562692 Status: Offline Sonork: 100.1679408 Thanks Meter: 51	LG MS210 latest firmware Reset FRP successfully done THANKS --OCTOPLUS TEAM Welcome to Octoplus FRP Tool v.1.2.4 Platform: LG Selected model: MS210 Put the phone into Download Mode: 1. Power phone OFF; 2. Press and hold "Vol+" button and connect USB cable. Searching for a phone. Please wait... Found phone on COM784 Reading info... Detected phone model: LGMS210 Warning: Selected model (MS210) differs from the detected one (LGMS210)! Mode: Emergency Initializing.. SW version: LGMS210AT-00-V10t-MPCS-US-NOV-14-2017-ARB00+0 Android version: 7.0 Reset FRP operation for MS210 will delete all user data on the phone (contacts, pictures and others)! Do You want to continue? Reading partition... Detecting writing method... Trying to repeat.. Trying third method... Resetting FRP lock.. Writing loader... Writing userdata... Formating encrypt section Restoring loader... Perform factory reset to complete operation! FRP lock is successfully reseted! Performed by 1.2.4.0 Software version. Report Post Last edited by Octopus box; 04-28-2018 at 08:35.

04-28-2018, 15:48	#575 (permalink)
kaka16dz Freak Poster Join Date: Dec 2011 Location: ALGERIA Posts: 195 Member: 1706377 Status: Offline Thanks Meter: 61	LG K7 X210DS Reset FRP successfully done LG K7 X210DS Reset FRP successfully done: Welcome to Octoplus FRP Tool v.1.2.3 Platform: LG Selected model: X210DS Please, power phone OFF and connect USB cable. Searching for a phone. Please wait... Found phone on COM238 Detecting Chip Version... HW Chip: MT6580: 6580.0000 HW Version: 8A00.CA00.0000.0000 Connecting... Brom Version: FF BootLoader Version: 01 Searching Download Agent... Selected DA: MTK_AllInOne_DA_Octoplus_v1.1, n.0 Sending Download Agent... DA sent successfully Initializing DA... Synchronizing with DA... NAND Flash: not installed eMMC Flash: .15010051.3732534D.4200D0B7.D3544359 eMMC Flash: Samsung: Q72SMB DA ver: 4.2.94 Initializing Memory Flash.. Initialization successfully completed Sending loaders... Loader send successfuly. Reading Flash Info... EMMC rpmb size: 0 Mb EMMC boot1 size: 4 Mb EMMC boot2 size: 4 Mb EMMC gp1 size: 0 Mb EMMC gp2 size: 0 Mb EMMC gp3 size: 0 Mb EMMC gp4 size: 0 Mb EMMC user area size: 7456 Mb Internal RAM size: 128 Kb External RAM size: 1024 Mb Reading partition... Reading info... Brand: lge Model: LG-X210 Device: m13g Platform: mt6580 Android version: 5.1 Searching for signatures... Resetting FRP lock.. FRP lock is successfully reseted! Backup saved as LG_X210DS_28-04-2018_16-43-32.dump file Performed by 1.2.3.0 Software version. Last edited by Octopus box; 04-28-2018 at 15:59.

04-29-2018, 12:30	#576 (permalink)
pintu_das No Life Poster Join Date: Jan 2015 Location: Narsingdi, Dhaka, Bangladesh Age: 28 Posts: 2,212 Member: 2325851 Status: Offline Sonork: 100.1680491 Thanks Meter: 2,386	Huawei Y7 Prime Dual SIM 32GB TRT-L21A FRP lock is successfully reseted! Huawei Y7 Prime Dual SIM 32GB TRT-L21A FRP lock is successfully reseted! Put the phone in FastBoot Mode: 1. Remove SD and SIM cards from the phone 2. Power phone OFF 3. Press and hold "Vol-" and insert USB cable 4. Wait until the phone enter in FastBoot Mode Welcome to Octoplus FRP Tool v.1.2.4 Platform: HUAWEI Selected model: TRT-L21A Put the phone in FastBoot Mode: 1. Remove SD and SIM cards from the phone 2. Power phone OFF 3. Press and hold "Vol-" and insert USB cable 4. Wait until the phone enter in FastBoot Mode Searching for a phone. Please wait... Detected phone model: TRT-L21A Phone SN: VWD7N17818009441 Phone IMEI: 864753036740081 Connecting to server..OK Authorizing...OK Resetting FRP lock.. If the device didn't reboot automatically, try to reconnect USB cable or re-boot it manually. FRP lock is successfully reseted! Performed by 1.2.4.0 Software version. THANKS OCTOPUS TEAM Last edited by Octopus box; 04-30-2018 at 09:31.

04-30-2018, 00:07	#578 (permalink)
jseyedanas No Life Poster Join Date: Jan 2006 Location: PORTUGAL Posts: 766 Member: 216446 Status: Offline Thanks Meter: 220	HISENCE C1 Reset FRP successfully done Model: HISENCE C1 FRP REMOVE SUCESSFUL Platform: _GENERAL RESET FRP METHODS Selected model: ADB METHOD Searching for a phone (waiting for ADB device)... Please, press "OK" button on the phone to allow USB debugging.. Phone found. Reading info... Phone model: Hisense Hisense C1 SW version: LMY47V Date: 2016年 12月 26日星期一 11:27:09 CST Android version: 5.1.1 Baseband M8936FAAAANUZM-1.37561.1.38671.1 Resetting FRP lock.. FRP lock is successfully reseted! Performed by 1.2.3.0 Software version. Last edited by Octopus box; 04-30-2018 at 09:35.

04-30-2018, 00:08	#579 (permalink)
jseyedanas No Life Poster Join Date: Jan 2006 Location: PORTUGAL Posts: 766 Member: 216446 Status: Offline Thanks Meter: 220	Wiko Jerry 2 FRP successfully removed Model: Wiko Jerry 2 FRP REMOVE SUCESSFUL Platform: WIKO Selected model: JERRY 2 Please, power phone OFF and connect USB cable. Searching for a phone. Please wait... Found phone on COM37 Detecting Chip Version... HW Chip: MT6580: 6580.0000 HW Version: 8A00.CA00.0000.0000 Connecting... Brom Version: FF BootLoader Version: 01 Searching Download Agent... Selected DA: MTK_AllInOne_DA_Octoplus_v1.0_PL, n.1 Sending Download Agent... DA sent successfully Initializing DA... Synchronizing with DA... NAND Flash: not installed eMMC Flash: .15010046.4536324D.420329A8.F2EFA471 eMMC Flash: Samsung: FE62MB DA ver: 4.2.9C Initializing Memory Flash.. Initialization successfully completed Sending loaders... Loader send successfuly. Reading Flash Info... EMMC rpmb size: 4 Mb EMMC boot1 size: 4 Mb EMMC boot2 size: 4 Mb EMMC gp1 size: 0 Mb EMMC gp2 size: 0 Mb EMMC gp3 size: 0 Mb EMMC gp4 size: 0 Mb EMMC user area size: 14910 Mb Internal RAM size: 128 Kb External RAM size: 1024 Mb Reading partition... Reading info... Brand: WIKO Model: JERRY2 Device: v2610 Platform: mt6580 Android version: 7.0 Display ID: alps-mp-n0.mp2-V1_tinno6580.we.n_P136 Searching for signatures... Resetting FRP lock.. FRP lock is successfully reseted! Backup saved as WIKO_JERRY 2_29-04-2018_23-56-53.dump file Performed by 1.2.3.0 Software version Last edited by Octopus box; 04-30-2018 at 09:37.

04-30-2018, 05:57	#580 (permalink)
pintu_das No Life Poster Join Date: Jan 2015 Location: Narsingdi, Dhaka, Bangladesh Age: 28 Posts: 2,212 Member: 2325851 Status: Offline Sonork: 100.1680491 Thanks Meter: 2,386	Huawei P9 Lite VNS-L21 2GB RAM FRP lock is successfully reseted! Huawei P9 Lite VNS-L21 2GB RAM FRP lock is successfully reseted! Put the phone in FastBoot Mode: 1. Remove SD and SIM cards from the phone 2. Power phone OFF 3. Press and hold "Vol-" and insert USB cable 4. Wait until the phone enter in FastBoot Mode Welcome to Octoplus FRP Tool v.1.2.4 Platform: HUAWEI Selected model: VNS-L21 Put the phone in FastBoot Mode: 1. Remove SD and SIM cards from the phone 2. Power phone OFF 3. Press and hold "Vol-" and insert USB cable 4. Wait until the phone enter in FastBoot Mode Searching for a phone. Please wait... Detected phone model: VNS-L21 Phone SN: BUC4C16826007091 Phone IMEI: 862264035999811 Phone IMEI: 862264036039823 SW version: VNS-L21C185B360 Connecting to server..OK Authorizing...OK Resetting FRP lock.. If the device didn't reboot automatically, try to reconnect USB cable or re-boot it manually. FRP lock is successfully reseted! Performed by 1.2.4.0 Software version. Last edited by Octopus box; 04-30-2018 at 09:38.

04-30-2018, 10:42	#581 (permalink)
onz No Life Poster Join Date: Aug 2013 Location: Bulawayo zimbabwe Posts: 1,676 Member: 2012334 Status: Offline Sonork: 100.1658100 Thanks Meter: 777	🐙 Huawei VNS-L31 Reset FRP Successfully Done Last edited by Octopus box; 04-30-2018 at 11:34.

04-30-2018, 11:05	#582 (permalink)
Smart144 Freak Poster Join Date: Oct 2014 Location: Ukraine, Poland Age: 36 Posts: 101 Member: 2273856 Status: Offline Thanks Meter: 61	Samsung A510F Android 7, FRP lock is successfully reseted!

04-30-2018, 12:39	#583 (permalink)
mmurugan1978 No Life Poster Join Date: Jul 2009 Location: CHENNAI Posts: 721 Member: 1079392 Status: Offline Thanks Meter: 444	Asus X00GD FRP unlock success Platform: ASUS Selected model: ZC521TL (X00GD) Please, power phone OFF, press and hold "Vol-" button and connect USB cable. Searching for a phone. Please wait... Found phone on COM3 Detecting Chip Version... HW Chip: MT6755: 0326.0000 HW Version: 8A00.CB00.0001.0000 HW Chip: MT6750: 00000442 Connecting... Brom Version: 05 BootLoader Version: FE Sending auth... Searching Download Agent... Selected DA: MTK_AllInOne_DA_Octoplus_v1.0_PL, n.0 Sending Download Agent... DA sent successfully Initializing DA... Synchronizing with DA... Mobile Status: SYNC DA ver: 2099.3.3 Mobile Status: brom Sending BootLoader Info... Initializing Memory Flash.. Initialization successfully completed Sending loaders... Mobile Status: SYNC Reading Flash Info... EMMC rpmb size: 4 Mb EMMC boot1 size: 4 Mb EMMC boot2 size: 4 Mb EMMC gp1 size: 0 Mb EMMC gp2 size: 0 Mb EMMC gp3 size: 0 Mb EMMC gp4 size: 0 Mb EMMC user area size: 29820 Mb eMMC Flash: .13014E51.334A3937.56100317.8E60B3B1 eMMC Flash: Unknown: Q3J97V Internal RAM size: 256 Kb External RAM size: 3072 Mb Reading partition... Reading info... Brand: asus Model: ASUS_X00GD Device: ASUS_X00G_1 Platform: mt6750 Android version: 7.0 Display ID: IN_Phone-14.02.1801.29-20180125 Searching for signatures... Resetting FRP lock.. FRP lock is successfully reseted! Last edited by Octopus box; 05-01-2018 at 09:32.

04-30-2018, 13:34	#585 (permalink)
Surtax No Life Poster Join Date: Aug 2013 Location: Russia, Ivanovo city Posts: 662 Member: 2006990 Status: Offline Thanks Meter: 540	🐙 Huawei LUA-U22 Reset FRP Successfully DONE Welcome to Octoplus FRP Tool v.1.2.4 Platform: HUAWEI Selected model: LUA-U22 Please, power phone OFF and connect USB cable. Searching for a phone. Please wait... Found phone on COM53 Detecting Chip Version... HW Chip: MT6582: 6582.0000 HW Version: 8A00.CA01.0001.0000 Connecting... Brom Version: FF BootLoader Version: 01 Searching Download Agent... Selected DA: MTK_AllInOne_DA_Octoplus_v1.1, n.2 Sending Download Agent... DA sent successfully Initializing DA... Synchronizing with DA... NAND Flash: not installed eMMC Flash: .90014A48.38473165.05075417.14AC5345 eMMC Flash: Hynix: H8G1e DA ver: 4.2.87 Initializing Memory Flash.. Initialization successfully completed Sending loaders... Loader send successfuly. Reading Flash Info... EMMC rpmb size: 4 Mb EMMC boot1 size: 4 Mb EMMC boot2 size: 4 Mb EMMC gp1 size: 0 Mb EMMC gp2 size: 0 Mb EMMC gp3 size: 0 Mb EMMC gp4 size: 0 Mb EMMC user area size: 7456 Mb Internal RAM size: 128 Kb External RAM size: 1024 Mb Reading partition... Reading partition... Reading info... Brand: HUAWEI Model: HUAWEI LUA-U22 Device: HWLUA-U6582 Platform: mt6582 Android version: 5.1 Display ID: LUA-U22C479B006 Searching for signatures... Resetting FRP lock.. FRP lock is successfully reseted! Backup saved as HUAWEI_LUA-U22_30-04-2018_15-09-10.dump file Performed by 1.2.4.0 Software version. Thanks Octopus Team!!! Last edited by Octopus box; 05-01-2018 at 09:46.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode