Huawei ATU-L11 dead flashing error by EDL

[byteforce2016]

Have received this set that goes into fastboot only and I thought to write a full firmware and when I wrote it it just goes into EDL mode,

Now when I want to write EDL board firmware it always stops at writing SBL1 below.

Any advice?

Found COM ports:
1: COM22 HS-USB Diagnostics 9008
2: COM3 Intel(R) Active Management Technology - SOL

Job ID: 0000000001A06330
2023-01-14 14:29:50
Starting Write Firmware(Factory mode)
Selected phone model: ‪ATU-L11‬
Selected download file: C:/Users/user/Desktop/ATU-L11-BD 1.0.0.53_Board Software_general_8.0.0_r1_Google_05022JHT File By (Support.HalabTech.Com)/Software/ATU-LX3-BD_1.0.0.53_Download.xml
Selected rawprogram file: C:/Users/user/Desktop/ATU-L11-BD 1.0.0.53_Board Software_general_8.0.0_r1_Google_05022JHT File By (Support.HalabTech.Com)/Software/bootloaderimage/rawprogram0.xml
Selected patch file: C:/Users/user/Desktop/ATU-L11-BD 1.0.0.53_Board Software_general_8.0.0_r1_Google_05022JHT File By (Support.HalabTech.Com)/Software/bootloaderimage/patch0.xml
Selected firehose file: C:/Users/user/Desktop/Huawei Y6 2018 ATU-L11 Loader V10 File By (Support.HalabTech.Com)/Loader_V10.mbn
Selected Partial flashing mode!
Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage
Searching Qualcomm HS-USB QDLoader 9008 port...
Please, reconnect battery, connect USB cable with attached Test Point on your phone!
Detected ‪Qualcomm HS-USB QDLoader 9008‬ port
Connecting to device...
Hadshaking...
Write Firmware(Factory mode) failed.
Performed by ‪1.3.3‬ Software version.

Job ID: 0000000001A0638C
2023-01-14 14:31:57
Starting Write Firmware(Factory mode)
Selected phone model: ‪ATU-L11‬
Selected Partial flashing mode!
Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage
Searching Qualcomm HS-USB QDLoader 9008 port...
Please, reconnect battery, connect USB cable with attached Test Point on your phone!
Detected ‪Qualcomm HS-USB QDLoader 9008‬ port
Connecting to device...
Hadshaking...
Reading bootloader info...
OEM PK HASH: 6BC369511DA9CADB3A7AF61574F89DB385003D6241BDD1FF573DBA61BF6AE119
MSM HW ID: 000560E1
Serial Number: 588F899C
Sending loader Loader_V10.mbn...
Loader send successfully
Reconnecting, please wait...
Configuring device...
Reading partition table...
Writing. Please wait...
Writing SBL1 partition...
Write Firmware(Factory mode) failed.
Performed by ‪1.3.3‬ Software version.

[Ismail khan1978]

i think its emmc problem

use jtag to repartion emmc

or change emmc