Post here success stories with Octoplus Huawei Tool - Page 14 - GSM-Forum

Dr_Wolodya · 05-22-2020, 14:14

G7-L01 Unbrick by using board firmware successfully done:

Code:

2020-05-22 11:37:36.822	Starting Write Firmware(Board mode)
2020-05-22 11:37:36.851	Connecting to phone..
2020-05-22 11:37:36.858	Please, reconnect battery, connect USB cable with attached Test Point on your phone!
2020-05-22 11:37:37.438	Phone connect successfully
2020-05-22 11:37:37.446	Sending loader MPRG8916.mbn...
2020-05-22 11:37:39.780	Loader send successfully
2020-05-22 11:37:39.788	Reconnecting, please wait..
2020-05-22 11:37:40.297	Loading fastboot partition. Please wait...
2020-05-22 11:37:40.305	This can take about few minutes!
2020-05-22 11:44:50.217	Searching Fastboot devices...
2020-05-22 11:44:54.399	Total interfaces: 1
2020-05-22 11:44:54.399	Interface 0 : flags: 1, name(78): \\?\usb#vid_18d1&pid_d00d#6&b79e976&0&4#{f72fe0d4-cbcb-407d-8814-9ed673d0dd6b}
2020-05-22 11:44:54.605	Writing partition partition...
2020-05-22 11:45:27.582	Writing hyp partition...
2020-05-22 11:45:28.994	Writing rpm partition...
2020-05-22 11:45:30.409	Writing tz partition...
2020-05-22 11:45:31.834	Writing aboot partition...
2020-05-22 11:45:33.300	Writing boot partition...
2020-05-22 11:45:35.547	Writing recovery partition...
2020-05-22 11:45:37.859	Writing modem partition...
2020-05-22 11:45:42.138	Writing system partition...
2020-05-22 11:45:58.337	Writing 1 chunk from 7...
2020-05-22 11:46:17.549	Writing 2 chunk from 7...
2020-05-22 11:46:36.206	Writing 3 chunk from 7...
2020-05-22 11:46:56.833	Writing 4 chunk from 7...
2020-05-22 11:47:16.547	Writing 5 chunk from 7...
2020-05-22 11:47:36.009	Writing 6 chunk from 7...
2020-05-22 11:47:54.835	Writing 7 chunk from 7...
2020-05-22 11:48:00.073	Writing userdata partition...
2020-05-22 11:48:04.954	Writing persist partition...
2020-05-22 11:48:06.563	Writing cache partition...
2020-05-22 11:48:08.277	Writing cust partition...
2020-05-22 11:48:15.729	Writing sbl1 partition...
2020-05-22 11:48:17.148	Writing log partition...
2020-05-22 11:48:22.760	Note: After successful reflash the phone in Board Firmware mode, for a correct work of the device, you need to reflash it in Upgrade mode!
2020-05-22 11:48:23.974	
2020-05-22 11:48:23.986	Write Firmware(Board mode) done.
2020-05-22 11:48:23.998	Performed by 1.1.8 Software version.

G7-L01 Repair vendor successfully done:

Code:

Starting Connect
Selected phone model: ‪G7-L01‬
Connecting to server...
Authorization is successful

Device Model: ‪G7-L01‬
Firmware: ‪HL1G760SM‬
Boot: ‪G7-L01V100R001C00B263_BOOT‬
System: ‪G7-L01V100R001C00B263_SYSTEM‬
Recovery: ‪G7-L01V100R001C00B263_RECOVERY‬
MEID: ‪00000000000000‬
PESN: ‪00000000‬
IMEI A: ‪149DA4E607AB9DE‬
Bluetooth MAC: ‪00:00:00:00:01:EE‬
WiFi MAC: ‪00:00:00:00:01:EE‬

Connect done.
Performed by ‪1.1.8‬ Software version.

2020-05-22 12:27:22 GMT -------------------------------------------------
Starting Repair Info
New Product Name: ‪G7-L01‬
New IMEI A: ‪864324028484011‬
New S/N: ‪Q9Z7N15822000510‬
New Board S/N: ‪Q9Z7N15822000510‬
New Vendor Code: ‪hw‬
New Country Code: ‪eu‬
New SIM Card Mode: ‪single‬
Repairing Product Name...
Error: Repair Product Name failed
Repairing BSN...
Repairing SN...
Repairing IMEI A...
Repairing Vendor/Country code...
Enabling software downgrade...
Repairing Sim Card Mode...
Resetting your device

Repair Info done.
Performed by ‪1.1.8‬ Software version.

galijus · 05-27-2020, 11:53

Code:

Welcome to Octoplus Huawei Software v.‪1.1.8‬

To enable 'Manufacture' mode dial
- for Qualcomm and Hisilicon based models: *#*#2846579#*#*
ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
- for MTK based models: *#*#14789632#*#*
ProjectMenu > Background Settings > USB Port Settings > Debug Mode

To enable 'Fastboot' mode
1. Power off the phone. Remove SD and SIM cards
2. Press 'Vol-' and insert USB cable
3. Wait until phone enters 'Fastboot' mode

To enable 'Upgrade' mode
1. Power off the phone. Remove SD and SIM cards
2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
3. Wait until phone enters 'Upgrade mode'

Found COM ports:
1: COM1 Communications Port
2: COM3 USB Serial Port

2020-05-27 10:35:35 GMT -------------------------------------------------
Starting Connect
Selected phone model: ‪MYA-L11‬
Searching devices in META mode
Please Power off the phone and insert USB cable
MTK Preloader COM port is not found

Connect failed.
Performed by ‪1.1.8‬ Software version.

2020-05-27 10:35:59 GMT -------------------------------------------------
Starting Connect
Selected phone model: ‪MYA-L11‬
Searching devices in META mode
Please Power off the phone and insert USB cable
Switching device to MTK META mode
Send para V1 OK!
Waiting for device loading
BaseBand chip: MT6737T,S01
S/W version: Maya-L11C432B181 
H/W board version: S01 
BaseBand chip: ‪MT6735, E00‬
S/W version: ‪MOLY.LR9.W1444.MD.LWTG.MP.V94.P66‬
H/W board version: ‪HQ6737T_66_1HA_M0_HW‬
IMEI A: ‪xxxxxxxxxxxxxxxx

Connect done.
Performed by ‪1.1.8‬ Software version.

2020-05-27 10:36:46 GMT -------------------------------------------------
Starting Repair Info
New IMEI A: ‪8675450371xxxxxx
Reading secure data...

Repair Info done.
Performed by ‪1.1.8‬ Software version.

sky73 · 06-11-2020, 13:15

bla-l29 imei repair done (mate 10 pro android 9}

write board sofware

repair imei

write stock firmware in upgrade mode

Code:

2020-06-11 11:12:41.195    Starting Write Firmware(Board mode)
2020-06-11 11:12:41.341    Phone connect successfully
2020-06-11 11:12:41.344    Updating bootloader...
2020-06-11 11:12:41.345    Writing xloader partition..
2020-06-11 11:12:42.927    Writing uce partition..
2020-06-11 11:12:44.222    Writing fastboot partition..
2020-06-11 11:13:03.925    Boot board firmware files has been written successfully
2020-06-11 11:13:03.925    Rebooting to fastboot mode..
2020-06-11 11:13:13.928    Searching Fastboot devices...
2020-06-11 11:13:13.943    Total interfaces: 1
2020-06-11 11:13:13.943    Interface 0 : flags: 1, name(81): \\?\usb#vid_18d1&pid_d00d#aqh7n18112004536#{f72fe0d4-cbcb-407d-8814-9ed673d0dd6b}
2020-06-11 11:13:15.768    Device Model: BLA-L29
2020-06-11 11:13:15.768    System: BLA-L29 9.1.0.341(C185E7R1P14)
2020-06-11 11:13:15.784    MEID: A00000845BB4AD
2020-06-11 11:13:15.784    IMEI A: 868389032363333
2020-06-11 11:13:15.800    IMEI B: 868389032372888
2020-06-11 11:13:15.800    S/N: AQH7N18112004536
2020-06-11 11:13:15.971    Erasing modemnvm_backup partition..
2020-06-11 11:13:16.174    Erasing modemnvm_factory partition..
2020-06-11 11:13:16.377    Erasing modemnvm_system partition..
2020-06-11 11:13:16.580    Erasing cust partition..
2020-06-11 11:13:17.516    Erasing misc partition..
2020-06-11 11:13:17.718    Erasing bootfail_info partition..
2020-06-11 11:13:17.921    Erasing dfx partition..
2020-06-11 11:13:18.124    Erasing rrecord partition..
2020-06-11 11:13:18.327    Erasing patch partition..
2020-06-11 11:13:18.732    Writing XLOADER partition...
2020-06-11 11:13:20.168    Writing PTABLE partition...
2020-06-11 11:13:21.634    Writing FASTBOOT partition...
2020-06-11 11:13:23.163    Writing VECTOR partition...
2020-06-11 11:13:24.614    Writing DTS partition...
2020-06-11 11:13:26.284    Writing DTO partition...
2020-06-11 11:13:27.766    Writing FW_LPM3 partition...
2020-06-11 11:13:29.201    Writing SENSORHUB partition...
2020-06-11 11:13:30.683    Writing FW_HIFI partition...
2020-06-11 11:13:32.259    Writing TEEOS partition...
2020-06-11 11:13:33.787    Writing RECOVERY_RAMDISK partition...
2020-06-11 11:13:35.847    Writing RECOVERY_VENDOR partition...
2020-06-11 11:13:37.578    Writing CACHE partition...
2020-06-11 11:13:39.247    Writing KERNEL partition...
2020-06-11 11:13:41.369    Writing RAMDISK partition...
2020-06-11 11:13:43.163    Writing HHEE partition...
2020-06-11 11:13:44.598    Writing HDCP partition...
2020-06-11 11:13:46.033    Writing VBMETA partition...
2020-06-11 11:13:47.469    Writing ODM partition...
2020-06-11 11:13:54.007    Writing TRUSTFIRMWARE partition...
2020-06-11 11:13:55.442    Writing MODEM_FW partition...
2020-06-11 11:13:58.687    Writing MODEMNVM_UPDATE partition...
2020-06-11 11:14:00.295    Writing MODEMNVM_CUST partition...
2020-06-11 11:14:01.746    Writing ISP_FIRMWARE partition...
2020-06-11 11:14:03.118    Erasing USERDATA partition..
2020-06-11 11:14:08.064    Writing USERDATA partition...
2020-06-11 11:14:20.079    Writing SYSTEM partition...
2020-06-11 11:14:34.868    Writing 1 chunk from 3...
2020-06-11 11:14:51.326    Writing 2 chunk from 3...
2020-06-11 11:15:07.847    Writing 3 chunk from 3...
2020-06-11 11:15:22.417    Writing VENDOR partition...
2020-06-11 11:15:32.152    Writing 1 chunk from 2...
2020-06-11 11:15:47.020    Writing 2 chunk from 2...
2020-06-11 11:15:55.100    Erasing PRODUCT partition..
2020-06-11 11:15:56.146    Writing PRODUCT partition...
2020-06-11 11:16:03.134    Erasing VERSION partition..
2020-06-11 11:16:03.540    Writing VERSION partition...
2020-06-11 11:16:05.162    Writing SPLASH2 partition...
2020-06-11 11:16:06.832    Writing HISEE_IMG partition...
2020-06-11 11:16:08.298    Writing HISEE_FS partition...
2020-06-11 11:16:09.874    Writing HIBENCH_DATA partition...
2020-06-11 11:16:19.639    Writing UFS_FW partition...
2020-06-11 11:16:23.118    Note: After successful reflash the phone in Board Firmware mode, for a correct work of the device, you need to reflash it in Upgrade mode!
2020-06-11 11:16:23.134    
2020-06-11 11:16:23.149    Write Firmware(Board mode) done.
2020-06-11 11:16:23.149    Performed by 1.1.9 Software version.
2020-06-11 11:19:06.810    2020-06-11 11:19:06 GMT -------------------------------------------------
2020-06-11 11:19:06.826    Starting Connect
2020-06-11 11:19:06.826    Selected phone model: BLA-L29
2020-06-11 11:19:09.544    Connecting to server...
2020-06-11 11:19:13.827    Check auth 1
2020-06-11 11:19:15.359    Authorization is successful
2020-06-11 11:19:15.363    Reading basic data...
2020-06-11 11:19:15.859    Reading secure data...
2020-06-11 11:19:22.466    Device Model: BLA-L29
2020-06-11 11:19:22.476    Firmware: System-FAC 6.0.0.030(0139)
2020-06-11 11:19:22.482    Boot: System-FAC 6.0.0.030(0139)_BOOT
2020-06-11 11:19:22.489    Fastboot: Chipset-boston8.0.0.1(0047)_FASTBOOT
2020-06-11 11:19:22.496    System: System-FAC 6.0.0.030(0139)
2020-06-11 11:19:22.502    Recovery: (unknow)
2020-06-11 11:19:22.509    MEID: yyyyyyyy
2020-06-11 11:19:22.513    PESN: yyyyyy
2020-06-11 11:19:22.518    IMEI A: yyyyyyyyy
2020-06-11 11:19:22.523    IMEI B: yyyyyyy
2020-06-11 11:19:22.529    Bluetooth MAC: 20:54:FA:B0:39:06
2020-06-11 11:19:22.534    WiFi MAC: 20:54:FA:B0:35:4B
2020-06-11 11:19:22.538    S/N: AQH7N18112004536
2020-06-11 11:19:22.544    Board S/N: 7N5AHP181B059628
2020-06-11 11:19:22.549    Vendor Code: hw
2020-06-11 11:19:22.554    Country Code: meafnaf
2020-06-11 11:19:22.560    
2020-06-11 11:19:22.565    Connect done.
2020-06-11 11:19:22.570    Performed by 1.1.9 Software version.
2020-06-11 11:19:33.989    2020-06-11 11:19:33 GMT -------------------------------------------------
2020-06-11 11:19:33.989    Starting Repair Info
2020-06-11 11:19:34.004    New IMEI A: yyyyyyyyyy
2020-06-11 11:19:34.004    New IMEI B: yyyyyyyyyyyyy
2020-06-11 11:19:34.020    Reading basic data...
2020-06-11 11:19:34.518    Reading secure data...
2020-06-11 11:19:41.128    Identifying security...
2020-06-11 11:19:41.319    Check auth 2
2020-06-11 11:19:42.500    Private enc 2
2020-06-11 11:19:43.180    Repairing IMEI A...
2020-06-11 11:19:43.195    Private enc 0
2020-06-11 11:19:51.493    Repairing IMEI B...
2020-06-11 11:19:51.501    Private enc 0
2020-06-11 11:19:59.284    Resetting your device
2020-06-11 11:19:59.338    
2020-06-11 11:19:59.349    Repair Info done.
2020-06-11 11:19:59.361    Performed by 1.1.9 Software version.
2020-06-11 11:28:02.820    Selected base file:
2020-06-11 11:28:16.325    Selected base file: F:/4c/tep/Huawei Mate 10 Pro BLA-L29C 8.0.0.140(C185) Firmware 8.0.0 r1 EMUI8.0 05014UYS androidhost.ru/Software/dload/update_sd/UPDATE.APP
2020-06-11 11:28:16.481    PACKAGE_TYPE: OFFLINE_UPDATE
2020-06-11 11:28:16.513    VERLIST : BLA_Global_C185_xloader
2020-06-11 11:28:24.276    Selected cust file: F:/4c/tep/Huawei Mate 10 Pro BLA-L29C 8.0.0.140(C185) Firmware 8.0.0 r1 EMUI8.0 05014UYS androidhost.ru/Software/dload/BLA-L29_hw_meafnaf/update_sd_BLA-L29_hw_meafnaf/update_BLA-L29_hw_meafnaf.app
2020-06-11 11:28:24.308    PACKAGE_TYPE: OFFLINE_UPDATE
2020-06-11 11:28:24.308    VERLIST : BLA_Global_C185_xloader
2020-06-11 11:28:29.288    Selected phone model: BLA-L29
2020-06-11 11:28:29.303    2020-06-11 11:28:29 GMT -------------------------------------------------
2020-06-11 11:28:29.319    Starting Write Firmware(Upgrade mode)
2020-06-11 11:28:29.334    Checking firmware package type
2020-06-11 11:28:29.350    Searching device in Upgrade mode...
2020-06-11 11:28:29.430    Connecting to phone..
2020-06-11 11:28:49.458    Phone connect successfully!
2020-06-11 11:28:49.479    Writing firmware partitions...
2020-06-11 11:28:49.499    Writing SHA256RSA partition...
2020-06-11 11:28:51.567    Writing CRC partition...
2020-06-11 11:28:53.696    Writing CURVER partition...
2020-06-11 11:28:55.711    Writing VERLIST partition...
2020-06-11 11:28:57.719    Writing PACKAGE_TYPE partition...
2020-06-11 11:28:59.723    Writing HISIUFS_GPT partition...
2020-06-11 11:29:01.961    Writing XLOADER partition...
2020-06-11 11:29:04.130    Writing FW_LPM3 partition...
2020-06-11 11:29:06.298    Writing HHEE partition...
2020-06-11 11:29:08.373    Writing FASTBOOT partition...
2020-06-11 11:29:11.181    Writing VECTOR partition...
2020-06-11 11:29:13.568    Writing VBMETA partition...
2020-06-11 11:29:15.611    Writing MODEMNVM_UPDATE partition...
2020-06-11 11:29:19.527    Writing MODEMNVM_CUST partition...
2020-06-11 11:29:21.929    Writing TEEOS partition...
2020-06-11 11:29:25.112    Writing TRUSTFIRMWARE partition...
2020-06-11 11:29:27.233    Writing SENSORHUB partition...
2020-06-11 11:29:29.776    Writing FW_HIFI partition...
2020-06-11 11:29:33.333    Writing KERNEL partition...
2020-06-11 11:29:41.320    Writing RAMDISK partition...
2020-06-11 11:29:47.326    Writing RECOVERY_RAMDISK partition...
2020-06-11 11:29:57.172    Writing RECOVERY_VENDOR partition...
2020-06-11 11:30:03.320    Writing RECOVERY_VBMETA partition...
2020-06-11 11:30:05.350    Writing ERECOVERY_KERNEL partition...
2020-06-11 11:30:13.420    Writing ERECOVERY_RAMDISK partition...
2020-06-11 11:30:23.716    Writing ERECOVERY_VENDOR partition...
2020-06-11 11:30:30.299    Writing ERECOVERY_VBMETA partition...
2020-06-11 11:30:32.329    Writing HDCP partition...
2020-06-11 11:30:34.458    Writing DTS partition...
2020-06-11 11:30:39.201    Writing DTO partition...
2020-06-11 11:30:41.884    Writing CACHE partition...
2020-06-11 11:30:46.190    Writing SYSTEM partition...
2020-06-11 11:44:33.336    Writing CUST partition...
2020-06-11 11:44:38.546    Writing ISP_FIRMWARE partition...
2020-06-11 11:44:42.259    Writing MODEM_FW partition...
2020-06-11 11:44:58.389    Writing HISEE_IMG partition...
2020-06-11 11:45:01.618    Writing HISEE_FS partition...
2020-06-11 11:45:04.832    Writing VENDOR partition...
2020-06-11 11:47:38.385    Writing VERSION partition...
2020-06-11 11:47:41.474    Writing ODM partition...
2020-06-11 11:48:14.203    Writing PRODUCT partition...
2020-06-11 11:48:58.455    Writing USERDATA partition...
2020-06-11 11:49:13.822    Writing UFSFW partition...
2020-06-11 11:49:17.503    
2020-06-11 11:49:17.550    Writing SHA256RSA partition...
2020-06-11 11:49:19.565    Writing CRC partition...
2020-06-11 11:49:21.600    Writing CURVER partition...
2020-06-11 11:49:23.631    Writing VERLIST partition...
2020-06-11 11:49:25.634    Writing PACKAGE_TYPE partition...
2020-06-11 11:49:27.639    Writing HISIUFS_GPT partition...
2020-06-11 11:49:29.767    Writing CUST partition...
2020-06-11 11:50:10.426    Writing VERSION partition...
2020-06-11 11:50:15.948    Writing USERDATA partition...
2020-06-11 11:56:14.461    
2020-06-11 11:56:18.205    Firmware writing successfully completed
2020-06-11 11:56:18.220    
2020-06-11 11:56:18.220    Write Firmware(Upgrade mode) done.
2020-06-11 11:56:18.236    Performed by 1.1.9 Software version.

niaz muhammad · 06-18-2020, 08:17

Welcome to Octoplus Huawei Software v.‪1.1.9‬

To enable 'Manufacture' mode dial
- for Qualcomm and Hisilicon based models: *#*#2846579#*#*
ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
- for MTK based models: *#*#14789632#*#*
ProjectMenu > Background Settings > USB Port Settings > Debug Mode

To enable 'Fastboot' mode
1. Power off the phone. Remove SD and SIM cards
2. Press 'Vol-' and insert USB cable
3. Wait until phone enters 'Fastboot' mode

To enable 'Upgrade' mode
1. Power off the phone. Remove SD and SIM cards
2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
3. Wait until phone enters 'Upgrade mode'

Found COM ports:
1: COM6 USB Serial Port
2: COM3 Intel(R) Active Management Technology - SOL
3: COM4 USB Serial Port
4: COM7 USB Serial Port
5: COM1 Communications Port

2020-06-18 06:38:29 GMT -------------------------------------------------
Starting Reset FRP (Fastboot Mode)
Searching Fastboot devices...

Device Model: ‪PRA-LX1‬
System: ‪PRA-LX1 8.0.0.360(IRLC432)‬
IMEI A: ‪862550032335706‬
IMEI B: ‪862550032365711‬
S/N: ‪HMKDU17126000399‬
Connecting to server...
Writing Reset FRP data...

Reset FRP (Fastboot Mode) done.
Performed by ‪1.1.9‬ Software version.

sky73 · 06-24-2020, 14:25

ane-lx1 dowgrade and imei repair

Code:

Device Model: ‪ANE-L21‬
Firmware: ‪System 8.0.0.046(0A5T)‬
Boot: ‪System 8.0.0.046(0A5T)_BOOT‬
Fastboot: ‪Chipset-dallas8.0.0.001(02D0)_FASTBOOT‬
System: ‪System 8.0.0.046(0A5T)‬
Recovery: ‪(unknow)‬
MEID: ‪00000000000000‬
PESN: ‪00000000‬
IMEI A:yyyyyyyyyyyyy
IMEI B: ‪yyyyyyyyyy
Bluetooth MAC: ‪90:94:97:48:10:4D‬
WiFi MAC: ‪90:94:97:48:00:AC‬
S/N: ‪9WV7N18313002675‬
Board S/N: ‪7N4VYH183D030874‬
Vendor Code: ‪hw‬
Country Code: ‪meafnaf‬

Connect done.
Performed by ‪1.1.9‬ Software version.

2020-06-24 13:18:16 GMT -------------------------------------------------
Starting Repair Info
New IMEI A: yyyyyyyyy
New IMEI B: ‪yyyyyy‬
Reading basic data...
Reading secure data...
Identifying security...
Repairing IMEI A...
Repairing IMEI B...
Resetting your device

Repair Info done.
Performed by ‪1.1.9‬ Software version.

hasitha123 · 06-25-2020, 22:25

Huawei Y6 Prime 2018 Dead repair done 100%

Starting Write Firmware(Board mode)
Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage
Connecting to phone..
Please, reconnect battery, connect USB cable with attached Test Point on your phone!
Phone connect successfully
Sending loader PROG_E~1.MBN...
Loader send successfully
Reconnecting, please wait..
Writing. Please wait...
Writing sbl1 partition...
Writing rpm partition...
Writing tz partition...
Writing devcfg partition...
Writing emmc_appsboot partition...
Writing cmnlib partition...
Writing cmnlib64 partition...
Writing keymaster partition...
Writing adspso partition...
Writing gpt_main0 partition...
Writing gpt_backup0 partition...
Patching. Please wait...
Patch done successfully
Searching Fastboot devices...
Error: Fastboot devices not found

Write Firmware(Board mode) canceled.
Performed by ‪1.1.9‬ Software version.

Sending an authorization request...
Analyzing Smart Card...
Authorized.

Selected phone model: ATU-L42
Partial flashing mode was selected!

2020-06-25 19:23:34 GMT -------------------------------------------------
Starting Write Firmware(Board mode)
Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage
Connecting to phone..
Please, reconnect battery, connect USB cable with attached Test Point on your phone!
Canceling... Please be patient!

Write Firmware(Board mode) failed.
Performed by ‪1.1.9‬ Software version.
Selected phone model: ATU-L42
Partial flashing mode was selected!

2020-06-25 19:29:38 GMT -------------------------------------------------
Starting Write Firmware(Board mode)
Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage
Connecting to phone..
Please, reconnect battery, connect USB cable with attached Test Point on your phone!
Phone connect successfully
Sending loader PROG_E~1.MBN...
Loader send successfully
Reconnecting, please wait..
Writing. Please wait...
Writing sbl1 partition...
Writing rpm partition...
Writing tz partition...
Writing devcfg partition...
Writing emmc_appsboot partition...
Writing cmnlib partition...
Writing cmnlib64 partition...
Writing keymaster partition...
Writing adspso partition...
Writing gpt_main0 partition...
Writing gpt_backup0 partition...
Patching. Please wait...
Patch done successfully
Searching Fastboot devices...
Error: Fastboot devices not found
Searching Fastboot devices...
Warning: Reading product model failed
Warning: oem get-build-number failed
Writing PARTITION partition...
Writing RPM partition...
Writing TZ partition...
Writing ABOOT partition...
Writing RAMDISK partition...
Writing KERNEL partition...
Writing RECOVERY_RAMDISK partition...
Writing RECOVERY_VENDOR partition...
Writing ERECOVERY_KERNEL partition...
Writing ERECOVERY_RAMDISK partition...
Writing ERECOVERY_VENDOR partition...
Writing MODEM partition...
Writing SYSTEM partition...
Writing 1 chunk from 3...
Writing 2 chunk from 3...
Writing 3 chunk from 3...
Writing USERDATA partition...
Writing PERSIST partition...
Writing CACHE partition...
Writing DSP partition...
Writing CMNLIB partition...
Writing CMNLIB64 partition...
Writing DEVCFG partition...
Writing KEYMASTER partition...
Writing LKSECAPP partition...
Writing APDP partition...
Writing MSADP partition...
Writing LOG partition...
Writing PRODUCT partition...
Writing VENDOR partition...
Writing 1 chunk from 2...
Writing 2 chunk from 2...
Writing VERSION partition...
Writing ODM partition...
Writing SBL1 partition...
Writing SEC partition...
Note: After successful reflash the phone in Board Firmware mode, for a correct work of the device, you need to reflash it in Upgrade mode!

Write Firmware(Board mode) done.
Performed by ‪1.1.9‬ Software version.

sky73 · 07-13-2020, 15:03

dra lx5 frp done

2020-07-13 13:53:39 GMT -------------------------------------------------
Starting Reset FRP (MTK Loader)
Please Power off the phone, Press 'Vol-' and insert USB cable

Detecting Chip Version...
HW Chip : MT6739
HW Version : 8A00.CB00.0002.0000
Brom Version: 5
Boot Loader Version: FE
Sending Authentication Data
Removing security protection...
Connecting to server...
Sending Download Agent...
DA successfully sent
Synchronizing with DA...
Mobile Status: SYNC
Mobile Status: brom
Sending BootLoader Info...
Initializing Memory Flash...
Initialization completed
Sending Loader...
Mobile Status: SYNC
Loader successfully sent
Reading Flash Info...
EMMC rpmb size : 4 Mb
EMMC boot1 size : 4 Mb
EMMC boot2 size : 4 Mb
EMMC gp1 size : 0 Mb
EMMC gp2 size : 0 Mb
EMMC gp3 size : 0 Mb
EMMC gp4 size : 0 Mb
EMMC user area size : 14910 Mb
Reading Partition Table
Reading FRP Partition
Writing FRP Partition data

Reset FRP (MTK Loader) done.
Performed by ‪1.2.0‬ Software version.

Dr_Wolodya · 07-14-2020, 19:57

Huawei ‪CHC-U01 Read Bootloader Code suuceesfully done:

Code:

Starting Connect
Selected phone model: ‪CHC-U01‬
Warning: Can't get device model.
Connecting to server...
Authorization is successful
Reading basic data...
Warning: Can't get device model.
Reading secure data...
Warning: Can't get phone MEID.
Error: Empty response packet.

Device Model: ‪Huawei HiSilicon Device‬
Firmware: ‪CHM-U01 V100R001C432B120CUSTC432D100‬
Boot: ‪DailyBuild_201507291026_BOOT‬
Fastboot: ‪DailyBuild_201507291026_FASTBOOT‬
System: ‪CHC-U01 V100R001C432B120_SYSTEM‬
Recovery: ‪(unknow)‬
IMEI A: ‪869537023114748‬
IMEI B: ‪869537023150759‬
Bluetooth MAC: ‪DC:EE:06:4E:23:C3‬
WiFi MAC: ‪DC:EE:06:4E:31:D4‬
S/N: ‪F4T4C16114000311‬
Board S/N: ‪4C3HMQ1615068825‬
Vendor Code: ‪hw‬
Country Code: ‪eu‬

Connect done.
Performed by ‪1.2.0‬ Software version.

2020-07-14 18:43:19 GMT -------------------------------------------------
Starting Read Bootloader Code
Reading basic data...
Warning: Can't read port lock.
Warning: Can't get device model.
Reading secure data...
Warning: Can't get phone MEID.
Error: Empty response packet.
Bootloader code: ‪1482211892724760‬

Read Bootloader Code done.
Performed by ‪1.2.0‬ Software version.

Dr_Wolodya · 07-15-2020, 11:58

Huawei ‪‪BG2-U01‬ Reset FRP suuceesfully done:

Code:

Starting Reset FRP (Fastboot Mode)
Searching Fastboot devices...

Device Model: ‪BG2-U01‬
System: ‪BG2-U01C170B182‬
IMEI A: ‪863129045765263‬
S/N: ‪BBKHGA196MC00027‬
Connecting to server...
Writing Reset FRP data...

Reset FRP (Fastboot Mode) done.
Performed by ‪1.2.0‬ Software version.

Dr_Wolodya · 07-22-2020, 16:13

Huawei VNS-L21 (7.0) Read Bootloader Code successfully done:

Code:

Starting Connect
Selected phone model: ‪VNS-L21‬
Warning: Can't get device model.
Warning: Can't get IMEI/MAC info.
Connecting to server...
Authorization is successful
Reading basic data...
Reading secure data...

Device Model: ‪VNS-L21‬
Firmware: ‪NRD90M test-keys‬
Boot: ‪Dallas-Trunk_BOOT‬
Fastboot: ‪Chipset-dallas 5.0.0.1(0EBX)_FASTBOOT‬
System: ‪System 5.0.0.57(1DFX)‬
Recovery: ‪(unknow)‬
MEID: ‪00000000000000‬
PESN: ‪00000000‬
IMEI A: ‪863692038811220‬
IMEI B: ‪863692038827622‬
Bluetooth MAC: ‪44:C3:46:DF:9E:35‬
WiFi MAC: ‪44:C3:46:DF:A4:9D‬
S/N: ‪BUC4C17210001866‬
Board S/N: ‪4C3SNC16BH053010‬
Vendor Code: ‪p4‬
Country Code: ‪pl‬

Connect done.
Performed by ‪1.2.0.1‬ Software version.

2020-07-22 15:02:55 GMT -------------------------------------------------
Starting Read Bootloader Code
Reading basic data...
Reading secure data...
Bootloader code: ‪6813211325676276‬

Read Bootloader Code done.
Performed by ‪1.2.0.1‬ Software version.

Change Vendor and Country + Enabling downgrade:

Code:

Starting Repair Info
New Vendor Code: ‪hw‬
New Country Code: ‪eu‬
Reading basic data...
Reading secure data...
Writing public keys...
Identifying security...
Repairing Vendor/Country code...
Enabling software downgrade...
Resetting your device

Repair Info done.
Performed by ‪1.2.0.1‬ Software version.

allumts · 07-24-2020, 15:59

Hello,

This Y7 Prime 2019 (DUB-LX1) had inside Unsupported Firmware version:

Quote:

DUB-LX1 8.2.0.156(C432CUSTC432D1)_Firmware_EMUI8.2_05015QG E File

Downgrated by Special Firmware and Patch for Qualcomm, then Imei Repair Done with Success!!!

LOG:

Quote:

2020-07-19 18:09:34.788 To enable 'Manufacture' mode dial
2020-07-19 18:09:34.788 - for Qualcomm and Hisilicon based models: *#*#2846579#*#*
2020-07-19 18:09:34.788 ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode
2020-07-19 18:09:34.788 - for MTK based models: *#*#14789632#*#*
2020-07-19 18:09:34.789 ProjectMenu > Background Settings > USB Port Settings > Debug Mode
2020-07-19 18:09:34.789
2020-07-19 18:09:34.789 To enable 'Fastboot' mode
2020-07-19 18:09:34.789 1. Power off the phone. Remove SD and SIM cards
2020-07-19 18:09:34.789 2. Press 'Vol-' and insert USB cable
2020-07-19 18:09:34.790 3. Wait until phone enters 'Fastboot' mode
2020-07-19 18:09:34.790
2020-07-19 18:09:34.790 To enable 'Upgrade' mode
2020-07-19 18:09:34.790 1. Power off the phone. Remove SD and SIM cards
2020-07-19 18:09:34.790 2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable
2020-07-19 18:09:34.791 3. Wait until phone enters 'Upgrade mode'
2020-07-19 18:09:34.847 Refreshing serial ports list
-------------------------------------------------
2020-07-19 18:09:40.011 Starting Connect
2020-07-19 18:09:40.013 Selected phone model: Qualcomm Android Device
2020-07-19 18:09:40.629 Connecting to server...
2020-07-19 18:09:41.755 Check auth 0
2020-07-19 18:09:42.805 Authorization is successful
2020-07-19 18:09:43.453 Device Model: DUB-LX1
2020-07-19 18:09:43.454 Boot: Chipset-sdm450 8.2.0.33(00O7)_SBL1
2020-07-19 18:09:43.456 System: System 8.2.0.036(03CV)
2020-07-19 18:09:43.458 MEID: 00000000000000
2020-07-19 18:09:43.459 PESN: 00000000
2020-07-19 18:09:43.461 IMEI A: 86575504XXXXXXX
2020-07-19 18:09:43.463 IMEI B: 86575504XXXXXXX
2020-07-19 18:09:43.465 Bluetooth MAC: 88:40:3B:53:45:10
2020-07-19 18:09:43.467 WiFi MAC: 88:40:3B:53:3A:1F
2020-07-19 18:09:43.468 S/N: 4FF6R194XXXXXX
2020-07-19 18:09:43.470 Board S/N: 6R5PGV1XXXXXXX
2020-07-19 18:09:43.472 Vendor Code: hw
2020-07-19 18:09:43.474 Country Code: eu
2020-07-19 18:09:43.477
2020-07-19 18:09:43.478 Connect done.
2020-07-19 18:09:43.480 Performed by 1.2.0.1 Software version.
2020-07-19 18:11:26.489 2020-07-19 18:11:26 GMT -------------------------------------------------
2020-07-19 18:11:26.491 Starting Repair Info
2020-07-19 18:11:26.494 New IMEI A: 865755045XXXXXX
2020-07-19 18:11:26.496 New IMEI B: 86575504XXXXXXX
2020-07-19 18:11:26.498 New Bluetooth MAC: 88403B534510
2020-07-19 18:11:26.501 New WI-Fi Mac: 88403B533A1F
2020-07-19 18:11:26.503 New S/N: 4FF6R1941XXXXXX
2020-07-19 18:11:26.506 New Board S/N: 6R5PGXXXXXX
2020-07-19 18:11:26.508 New Vendor Code: hw
2020-07-19 18:11:26.511 New Country Code: eu
2020-07-19 18:11:26.513 New SIM Card Mode: double
2020-07-19 18:11:27.205 Repairing BSN...
2020-07-19 18:11:27.316 Repairing SN...
2020-07-19 18:11:27.492 Repairing IMEI A...
2020-07-19 18:11:27.495 Private enc 0
2020-07-19 18:11:27.993 Repairing Bluetooth MAC...
2020-07-19 18:11:27.996 Private enc 0
2020-07-19 18:11:28.494 Repairing WiFi MAC...
2020-07-19 18:11:28.497 Private enc 0
2020-07-19 18:11:29.362 Repairing IMEI B...
2020-07-19 18:11:29.365 Private enc 0
2020-07-19 18:11:30.201 Repairing Vendor/Country...
2020-07-19 18:11:30.204 Private enc 0
2020-07-19 18:11:30.701 Private enc 0
2020-07-19 18:11:31.279 Repairing Sim Card Mode...
2020-07-19 18:11:31.282 Private enc 0
2020-07-19 18:11:31.860 Resetting your device
2020-07-19 18:11:31.922
2020-07-19 18:11:31.925 Repair Info done.
2020-07-19 18:11:31.928 Performed by 1.2.0.1 Software version.

BR
allumts

sky73 · 07-25-2020, 09:14

y625 u32 imei repair done

Code:

Starting Connect
Selected phone model: ‪Y625-U32‬
Authorization is successful
MEID: ‪00000000000000‬
PESN: ‪00000000‬
IMEI A: ‪869343020237297‬
Bluetooth MAC: ‪00:00:00:00:00:00‬
WiFi MAC: ‪00:00:00:00:00:00‬

Connect done.
Performed by ‪1.2.0.1‬ Software version.

2020-07-25 08:11:57 GMT -------------------------------------------------
Starting Repair Info
New IMEI A: ‪yyyyyyyyyyyy
New IMEI B: ‪yyyyyyyyyyyyy
Repairing IMEI A...
Repairing IMEI B...
Rebooting device...

Repair Info done.
Performed by ‪1.2.0.1‬ Software version.

Dr_Wolodya · 07-28-2020, 11:06

Huawei ‪‪MYA-L41‬ Reset FRP suuceesfully done:

Code:

2020-07-28 09:41:43 GMT -------------------------------------------------
Starting Reset FRP (MTK Loader)
Please Power off the phone and insert USB cable

Detecting Chip Version...
HW Chip : MT6737T
HW Version : 8A00.CA00.0000.0000
Brom Version: FF
Boot Loader Version: 01
Sending Download Agent...
DA successfully sent
Synchronizing with DA...
NAND Flash: not installed
eMMC Flash: 90014A48.41473461.32D42E23.6E5194A9
eMMC Flash: Hynix: HAG4a2
DA ver : 4.2.93
Initializing Memory Flash...
Initialization completed
Sending Loader...
Loader successfully sent
Reading Flash Info...
EMMC rpmb size : 4 Mb
EMMC boot1 size : 4 Mb
EMMC boot2 size : 4 Mb
EMMC gp1 size : 0 Mb
EMMC gp2 size : 0 Mb
EMMC gp3 size : 0 Mb
EMMC gp4 size : 0 Mb
EMMC user area size : 15028 Mb
Internal RAM size : 128 Kb
External RAM size : 2048 Mb
Reading Partition Table
Reading FRP Partition
Writing FRP Partition data

Reset FRP (MTK Loader) done.
Performed by ‪1.2.0‬ Software version.

MYA-L41 Read Bootloader Code in META mode successfully done:

Code:

2020-07-28 09:50:14 GMT -------------------------------------------------
Starting Connect
Selected phone model: ‪MYA-L41‬
Searching devices in META mode
Please Power off the phone and insert USB cable
Switching device to MTK META mode
Send para V1 OK!
Waiting for device loading
BaseBand chip: MT6737T,S01
S/W version: Maya-L41C432B146 
H/W board version: S01 
BaseBand chip: ‪MT6735, E00‬
S/W version: ‪MOLY.LR9.W1444.MD.LWTG.MP.V94.P66‬
H/W board version: ‪HQ6737T_66_1HA_M0_HW‬
IMEI A: ‪862664033165655‬
IMEI B: ‪862664035170869‬

Connect done.
Performed by ‪1.2.0‬ Software version.

2020-07-28 09:51:28 GMT -------------------------------------------------
Starting Read Bootloader Code
Reading secure data...
Bootloader code: ‪B475F051B1580681‬

Read Bootloader Code done.
Performed by ‪1.2.0‬ Software version.

mike090 · 08-01-2020, 04:42

2020-08-01 03:14:13.552 Starting ON/OFF Factory Mode
2020-08-01 03:14:13.615 Performing ON factory mode operation...
2020-08-01 03:14:13.615 Checking firmware package type
2020-08-01 03:14:13.615 Searching device in Upgrade mode...
2020-08-01 03:14:13.661 Connecting to phone..
2020-08-01 03:14:14.693 Phone connect successfully!
2020-08-01 03:14:14.693 Writing firmware partitions...
2020-08-01 03:14:14.709 Writing SHA256RSA partition...
2020-08-01 03:14:16.771 Writing CRC partition...
2020-08-01 03:14:18.884 Writing BASE_VERLIST partition...
2020-08-01 03:14:20.921 Writing BASE_VER partition...
2020-08-01 03:14:22.940 Writing PACKAGE_TYPE partition...
2020-08-01 03:14:24.962 Writing HISIUFS_GPT partition...
2020-08-01 03:14:27.029 Writing XLOADER partition...
2020-08-01 03:14:29.604
2020-08-01 03:14:29.619 ON/OFF Factory Mode done.
2020-08-01 03:14:29.635 Performed by 1.2.0.1 Software version.

2020-08-01 03:14:43.351 Starting Connect
2020-08-01 03:14:43.351 Selected phone model: EML-L09
2020-08-01 03:14:43.351 Searching HUAWEI USB COM 1.0 port...
2020-08-01 03:14:43.382 Updating bootloader KIRIN970_A8.1_V0..
2020-08-01 03:14:43.382 Initializing remote service connection
2020-08-01 03:14:50.956 Writing XLOADER partition...
2020-08-01 03:14:52.635 Writing UCE partition...
2020-08-01 03:14:53.917 Writing FASTBOOT partition...
2020-08-01 03:15:11.545 Bootloader Update successfully
2020-08-01 03:15:11.545 Rebooting to fastboot mode...
2020-08-01 03:15:11.561 Searching Fastboot devices...
2020-08-01 03:15:15.815 Total interfaces: 1
2020-08-01 03:15:15.816 Interface 0 : flags: 1, name(81): \\?\usb#vid_18d1&pid_d00d#bpn0218827000835#{f72fe0 d4-cbcb-407d-8814-9ed673d0dd6b}
2020-08-01 03:15:23.694 Device Model: EML-L09
2020-08-01 03:15:23.694 System: EML-L09 10.0.0.161(C605E3R1P3)
2020-08-01 03:15:23.710 MEID: A000009558836C
2020-08-01 03:15:23.710 IMEI A: 867129037677795
2020-08-01 03:15:23.725 IMEI B: 867129037677795
2020-08-01 03:15:23.725 S/N: BPN0218827000835
2020-08-01 03:15:23.725
2020-08-01 03:15:23.741 Connect done.
2020-08-01 03:15:23.741 Performed by 1.2.0.1 Software version.

2020-08-01 03:15:45.999 Starting Repair Info
2020-08-01 03:15:45.999 New IMEI A: 356629071073130
2020-08-01 03:15:46.015 Saving backup of MODEM_SECURE...
2020-08-01 03:15:46.477 Saving backup of OEMINFO...
2020-08-01 03:15:48.368 Saving backup of MODEMNVM_FACTORY...
2020-08-01 03:15:49.008 Saving backup of MODEMNVM_SYSTEM...
2020-08-01 03:15:49.633 Saving backup of MODEMNVM_IMG...
2020-08-01 03:15:52.275 Reading info from OEMINFO...
2020-08-01 03:15:52.322 OEMINFO Phone Model: EML-L09
2020-08-01 03:15:52.353 OEMINFO IMEI_A: 867129037677795
2020-08-01 03:15:52.400 OEMINFO IMEI_B: 867129037677795
2020-08-01 03:15:52.431 OEMINFO MEID: A000009558836C
2020-08-01 03:15:52.478 OEMINFO Build Number: EML-L09 8.1.0.156(C605)
2020-08-01 03:15:52.509 OEMINFO Vendor: hw
2020-08-01 03:15:52.540 OEMINFO Country: la
2020-08-01 03:15:52.900 Reading info from NV...
2020-08-01 03:15:52.962 NV IMEI_A: 867129037677795
2020-08-01 03:15:53.009 NV IMEI_B: 867129037677795
2020-08-01 03:15:53.322 Connecting to server...
2020-08-01 03:15:55.182 Private enc 2
2020-08-01 03:16:23.045 Repairing...
2020-08-01 03:16:23.498 Private enc 0
2020-08-01 03:16:46.418 Private enc 0
2020-08-01 03:17:09.172 Device with unsupported security patch
2020-08-01 03:17:09.375 Writing MODEM_SECURE partition...
2020-08-01 03:17:12.859 Device with unsupported security patch
2020-08-01 03:17:13.062 Writing OEMINFO partition...
2020-08-01 03:17:16.703 Device with unsupported security patch
2020-08-01 03:17:16.907 Writing MODEMNVM_FACTORY partition...
2020-08-01 03:17:19.376 Device with unsupported security patch
2020-08-01 03:17:19.579 Writing MODEMNVM_SYSTEM partition...
2020-08-01 03:17:22.173 Device with unsupported security patch
2020-08-01 03:17:22.376 Writing MODEMNVM_IMG partition...
2020-08-01 03:17:31.899 Rebooting device...
2020-08-01 03:17:32.914 Reboot failed
2020-08-01 03:17:34.915
2020-08-01 03:17:34.962 Repair Info done.
2020-08-01 03:17:35.009 Performed by 1.2.0.1 Software version.

2020-08-01 03:18:25.756 Starting ON/OFF Factory Mode
2020-08-01 03:18:25.788 Performing OFF factory mode operation...
2020-08-01 03:18:25.793 Searching HUAWEI USB COM 1.0 port...
2020-08-01 03:18:25.808 Updating bootloader KIRIN970_A8.1_V0..
2020-08-01 03:18:25.808 Initializing remote service connection
2020-08-01 03:18:43.140 Writing XLOADER partition...
2020-08-01 03:18:44.799 Writing UCE partition...
2020-08-01 03:18:46.080 Writing FASTBOOT partition...
2020-08-01 03:19:03.723 Bootloader Update successfully
2020-08-01 03:19:03.738 Rebooting to fastboot mode...
2020-08-01 03:19:03.754 Searching Fastboot devices...
2020-08-01 03:19:07.994 Total interfaces: 1
2020-08-01 03:19:07.994 Interface 0 : flags: 1, name(81): \\?\usb#vid_18d1&pid_d00d#bpn0218827000835#{f72fe0 d4-cbcb-407d-8814-9ed673d0dd6b}
2020-08-01 03:19:15.901 Device Model: EML-L09
2020-08-01 03:19:15.901 System: EML-L09 10.0.0.161(C605E3R1P3)
2020-08-01 03:19:15.917 MEID: A000009558836C
2020-08-01 03:19:15.932 IMEI A: 356629071073130
2020-08-01 03:19:15.948 IMEI B: 867129037677795
2020-08-01 03:19:15.964 S/N: BPN0218827000835
2020-08-01 03:19:15.964 Extracting firmware partitions...
2020-08-01 03:19:15.979 Partitions has been extracted successfully
2020-08-01 03:19:16.511 Device with unsupported security patch
2020-08-01 03:19:17.526 Writing XLOADER partition...
2020-08-01 03:19:20.975 Erasing MISC partition..
2020-08-01 03:19:21.385 Writing PATCH partition...
2020-08-01 03:19:22.791 Rebooting device...
2020-08-01 03:19:22.994
2020-08-01 03:19:23.025 ON/OFF Factory Mode done.
2020-08-01 03:19:23.056 Performed by 1.2.0.1 Software version.

faisal naeem · 08-12-2020, 08:36

Telenor Infinity I4 User Lock Remove Done with Octoplus FRP Tool

[IMG]file:///C:/Users/FAISAL%20NAEEM/Desktop/infinity%20i4.jpg[/IMG]

08-01-2020, 04:42	#209 (permalink)
mike090 Major Poster Join Date: Oct 2005 Location: Rancagua, Chile Age: 36 Posts: 46 Member: 195049 Status: Offline Thanks Meter: 15	Imei Repair P20 EML-L09 Android 10 without downgrade, without disassembly 2020-08-01 03:14:13.552 Starting ON/OFF Factory Mode 2020-08-01 03:14:13.615 Performing ON factory mode operation... 2020-08-01 03:14:13.615 Checking firmware package type 2020-08-01 03:14:13.615 Searching device in Upgrade mode... 2020-08-01 03:14:13.661 Connecting to phone.. 2020-08-01 03:14:14.693 Phone connect successfully! 2020-08-01 03:14:14.693 Writing firmware partitions... 2020-08-01 03:14:14.709 Writing SHA256RSA partition... 2020-08-01 03:14:16.771 Writing CRC partition... 2020-08-01 03:14:18.884 Writing BASE_VERLIST partition... 2020-08-01 03:14:20.921 Writing BASE_VER partition... 2020-08-01 03:14:22.940 Writing PACKAGE_TYPE partition... 2020-08-01 03:14:24.962 Writing HISIUFS_GPT partition... 2020-08-01 03:14:27.029 Writing XLOADER partition... 2020-08-01 03:14:29.604 2020-08-01 03:14:29.619 ON/OFF Factory Mode done. 2020-08-01 03:14:29.635 Performed by 1.2.0.1 Software version. 2020-08-01 03:14:43.351 Starting Connect 2020-08-01 03:14:43.351 Selected phone model: EML-L09 2020-08-01 03:14:43.351 Searching HUAWEI USB COM 1.0 port... 2020-08-01 03:14:43.382 Updating bootloader KIRIN970_A8.1_V0.. 2020-08-01 03:14:43.382 Initializing remote service connection 2020-08-01 03:14:50.956 Writing XLOADER partition... 2020-08-01 03:14:52.635 Writing UCE partition... 2020-08-01 03:14:53.917 Writing FASTBOOT partition... 2020-08-01 03:15:11.545 Bootloader Update successfully 2020-08-01 03:15:11.545 Rebooting to fastboot mode... 2020-08-01 03:15:11.561 Searching Fastboot devices... 2020-08-01 03:15:15.815 Total interfaces: 1 2020-08-01 03:15:15.816 Interface 0 : flags: 1, name(81): \\?\usb#vid_18d1&pid_d00d#bpn0218827000835#{f72fe0 d4-cbcb-407d-8814-9ed673d0dd6b} 2020-08-01 03:15:23.694 Device Model: EML-L09 2020-08-01 03:15:23.694 System: EML-L09 10.0.0.161(C605E3R1P3) 2020-08-01 03:15:23.710 MEID: A000009558836C 2020-08-01 03:15:23.710 IMEI A: 867129037677795 2020-08-01 03:15:23.725 IMEI B: 867129037677795 2020-08-01 03:15:23.725 S/N: BPN0218827000835 2020-08-01 03:15:23.725 2020-08-01 03:15:23.741 Connect done. 2020-08-01 03:15:23.741 Performed by 1.2.0.1 Software version. 2020-08-01 03:15:45.999 Starting Repair Info 2020-08-01 03:15:45.999 New IMEI A: 356629071073130 2020-08-01 03:15:46.015 Saving backup of MODEM_SECURE... 2020-08-01 03:15:46.477 Saving backup of OEMINFO... 2020-08-01 03:15:48.368 Saving backup of MODEMNVM_FACTORY... 2020-08-01 03:15:49.008 Saving backup of MODEMNVM_SYSTEM... 2020-08-01 03:15:49.633 Saving backup of MODEMNVM_IMG... 2020-08-01 03:15:52.275 Reading info from OEMINFO... 2020-08-01 03:15:52.322 OEMINFO Phone Model: EML-L09 2020-08-01 03:15:52.353 OEMINFO IMEI_A: 867129037677795 2020-08-01 03:15:52.400 OEMINFO IMEI_B: 867129037677795 2020-08-01 03:15:52.431 OEMINFO MEID: A000009558836C 2020-08-01 03:15:52.478 OEMINFO Build Number: EML-L09 8.1.0.156(C605) 2020-08-01 03:15:52.509 OEMINFO Vendor: hw 2020-08-01 03:15:52.540 OEMINFO Country: la 2020-08-01 03:15:52.900 Reading info from NV... 2020-08-01 03:15:52.962 NV IMEI_A: 867129037677795 2020-08-01 03:15:53.009 NV IMEI_B: 867129037677795 2020-08-01 03:15:53.322 Connecting to server... 2020-08-01 03:15:55.182 Private enc 2 2020-08-01 03:16:23.045 Repairing... 2020-08-01 03:16:23.498 Private enc 0 2020-08-01 03:16:46.418 Private enc 0 2020-08-01 03:17:09.172 Device with unsupported security patch 2020-08-01 03:17:09.375 Writing MODEM_SECURE partition... 2020-08-01 03:17:12.859 Device with unsupported security patch 2020-08-01 03:17:13.062 Writing OEMINFO partition... 2020-08-01 03:17:16.703 Device with unsupported security patch 2020-08-01 03:17:16.907 Writing MODEMNVM_FACTORY partition... 2020-08-01 03:17:19.376 Device with unsupported security patch 2020-08-01 03:17:19.579 Writing MODEMNVM_SYSTEM partition... 2020-08-01 03:17:22.173 Device with unsupported security patch 2020-08-01 03:17:22.376 Writing MODEMNVM_IMG partition... 2020-08-01 03:17:31.899 Rebooting device... 2020-08-01 03:17:32.914 Reboot failed 2020-08-01 03:17:34.915 2020-08-01 03:17:34.962 Repair Info done. 2020-08-01 03:17:35.009 Performed by 1.2.0.1 Software version. 2020-08-01 03:18:25.756 Starting ON/OFF Factory Mode 2020-08-01 03:18:25.788 Performing OFF factory mode operation... 2020-08-01 03:18:25.793 Searching HUAWEI USB COM 1.0 port... 2020-08-01 03:18:25.808 Updating bootloader KIRIN970_A8.1_V0.. 2020-08-01 03:18:25.808 Initializing remote service connection 2020-08-01 03:18:43.140 Writing XLOADER partition... 2020-08-01 03:18:44.799 Writing UCE partition... 2020-08-01 03:18:46.080 Writing FASTBOOT partition... 2020-08-01 03:19:03.723 Bootloader Update successfully 2020-08-01 03:19:03.738 Rebooting to fastboot mode... 2020-08-01 03:19:03.754 Searching Fastboot devices... 2020-08-01 03:19:07.994 Total interfaces: 1 2020-08-01 03:19:07.994 Interface 0 : flags: 1, name(81): \\?\usb#vid_18d1&pid_d00d#bpn0218827000835#{f72fe0 d4-cbcb-407d-8814-9ed673d0dd6b} 2020-08-01 03:19:15.901 Device Model: EML-L09 2020-08-01 03:19:15.901 System: EML-L09 10.0.0.161(C605E3R1P3) 2020-08-01 03:19:15.917 MEID: A000009558836C 2020-08-01 03:19:15.932 IMEI A: 356629071073130 2020-08-01 03:19:15.948 IMEI B: 867129037677795 2020-08-01 03:19:15.964 S/N: BPN0218827000835 2020-08-01 03:19:15.964 Extracting firmware partitions... 2020-08-01 03:19:15.979 Partitions has been extracted successfully 2020-08-01 03:19:16.511 Device with unsupported security patch 2020-08-01 03:19:17.526 Writing XLOADER partition... 2020-08-01 03:19:20.975 Erasing MISC partition.. 2020-08-01 03:19:21.385 Writing PATCH partition... 2020-08-01 03:19:22.791 Rebooting device... 2020-08-01 03:19:22.994 2020-08-01 03:19:23.025 ON/OFF Factory Mode done. 2020-08-01 03:19:23.056 Performed by 1.2.0.1 Software version.

06-18-2020, 08:17	#199 (permalink)
niaz muhammad No Life Poster Join Date: Feb 2011 Location: ( United States Of Islam ) Age: 35 Posts: 3,954 Member: 1519396 Status: Offline Sonork: 100.1612702 Thanks Meter: 1,951	Welcome to Octoplus Huawei Software v.‪1.1.9‬ To enable 'Manufacture' mode dial - for Qualcomm and Hisilicon based models: ##2846579## ProjectMenu > Background Settings > USB Port Settings > Manufacture Mode - for MTK based models: ##14789632## ProjectMenu > Background Settings > USB Port Settings > Debug Mode To enable 'Fastboot' mode 1. Power off the phone. Remove SD and SIM cards 2. Press 'Vol-' and insert USB cable 3. Wait until phone enters 'Fastboot' mode To enable 'Upgrade' mode 1. Power off the phone. Remove SD and SIM cards 2. Press and hold 'Vol-' and 'Vol+' keys and insert USB cable 3. Wait until phone enters 'Upgrade mode' Found COM ports: 1: COM6 USB Serial Port 2: COM3 Intel(R) Active Management Technology - SOL 3: COM4 USB Serial Port 4: COM7 USB Serial Port 5: COM1 Communications Port 2020-06-18 06:38:29 GMT ------------------------------------------------- Starting Reset FRP (Fastboot Mode) Searching Fastboot devices... Device Model: ‪PRA-LX1‬ System: ‪PRA-LX1 8.0.0.360(IRLC432)‬ IMEI A: ‪862550032335706‬ IMEI B: ‪862550032365711‬ S/N: ‪HMKDU17126000399‬ Connecting to server... Writing Reset FRP data... Reset FRP (Fastboot Mode) done. Performed by ‪1.1.9‬ Software version.

06-25-2020, 22:25	#201 (permalink)
hasitha123 Insane Poster Join Date: Apr 2016 Location: IN MY SWEET HOME Posts: 75 Member: 2565181 Status: Offline Thanks Meter: 11	Huawei Y6 Prime 2018 Dead repair done 100% Starting Write Firmware(Board mode) Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage Connecting to phone.. Please, reconnect battery, connect USB cable with attached Test Point on your phone! Phone connect successfully Sending loader PROG_E~1.MBN... Loader send successfully Reconnecting, please wait.. Writing. Please wait... Writing sbl1 partition... Writing rpm partition... Writing tz partition... Writing devcfg partition... Writing emmc_appsboot partition... Writing cmnlib partition... Writing cmnlib64 partition... Writing keymaster partition... Writing adspso partition... Writing gpt_main0 partition... Writing gpt_backup0 partition... Patching. Please wait... Patch done successfully Searching Fastboot devices... Error: Fastboot devices not found Write Firmware(Board mode) canceled. Performed by ‪1.1.9‬ Software version. Sending an authorization request... Analyzing Smart Card... Authorized. Selected phone model: ATU-L42 Partial flashing mode was selected! 2020-06-25 19:23:34 GMT ------------------------------------------------- Starting Write Firmware(Board mode) Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage Connecting to phone.. Please, reconnect battery, connect USB cable with attached Test Point on your phone! Canceling... Please be patient! Write Firmware(Board mode) failed. Performed by ‪1.1.9‬ Software version. Selected phone model: ATU-L42 Partial flashing mode was selected! 2020-06-25 19:29:38 GMT ------------------------------------------------- Starting Write Firmware(Board mode) Warning: Please, before firmware write, disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs. To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Android-based devices). Dont run any other programs or attach new devices to your computer during the flashing procedure! Don’t turn off phone and don’t disconnect cable during firmware write. Please, follow these simple instructions to avoid phone damage Connecting to phone.. Please, reconnect battery, connect USB cable with attached Test Point on your phone! Phone connect successfully Sending loader PROG_E~1.MBN... Loader send successfully Reconnecting, please wait.. Writing. Please wait... Writing sbl1 partition... Writing rpm partition... Writing tz partition... Writing devcfg partition... Writing emmc_appsboot partition... Writing cmnlib partition... Writing cmnlib64 partition... Writing keymaster partition... Writing adspso partition... Writing gpt_main0 partition... Writing gpt_backup0 partition... Patching. Please wait... Patch done successfully Searching Fastboot devices... Error: Fastboot devices not found Searching Fastboot devices... Warning: Reading product model failed Warning: oem get-build-number failed Writing PARTITION partition... Writing RPM partition... Writing TZ partition... Writing ABOOT partition... Writing RAMDISK partition... Writing KERNEL partition... Writing RECOVERY_RAMDISK partition... Writing RECOVERY_VENDOR partition... Writing ERECOVERY_KERNEL partition... Writing ERECOVERY_RAMDISK partition... Writing ERECOVERY_VENDOR partition... Writing MODEM partition... Writing SYSTEM partition... Writing 1 chunk from 3... Writing 2 chunk from 3... Writing 3 chunk from 3... Writing USERDATA partition... Writing PERSIST partition... Writing CACHE partition... Writing DSP partition... Writing CMNLIB partition... Writing CMNLIB64 partition... Writing DEVCFG partition... Writing KEYMASTER partition... Writing LKSECAPP partition... Writing APDP partition... Writing MSADP partition... Writing LOG partition... Writing PRODUCT partition... Writing VENDOR partition... Writing 1 chunk from 2... Writing 2 chunk from 2... Writing VERSION partition... Writing ODM partition... Writing SBL1 partition... Writing SEC partition... Note: After successful reflash the phone in Board Firmware mode, for a correct work of the device, you need to reflash it in Upgrade mode! Write Firmware(Board mode) done. Performed by ‪1.1.9‬ Software version.

07-13-2020, 15:03	#202 (permalink)
sky73 No Life Poster Join Date: Jan 2013 Location: gsmhosting Age: 29 Posts: 1,148 Member: 1876736 Status: Offline Thanks Meter: 735	dra lx5 frp done 2020-07-13 13:53:39 GMT ------------------------------------------------- Starting Reset FRP (MTK Loader) Please Power off the phone, Press 'Vol-' and insert USB cable Detecting Chip Version... HW Chip : MT6739 HW Version : 8A00.CB00.0002.0000 Brom Version: 5 Boot Loader Version: FE Sending Authentication Data Removing security protection... Connecting to server... Sending Download Agent... DA successfully sent Synchronizing with DA... Mobile Status: SYNC Mobile Status: brom Sending BootLoader Info... Initializing Memory Flash... Initialization completed Sending Loader... Mobile Status: SYNC Loader successfully sent Reading Flash Info... EMMC rpmb size : 4 Mb EMMC boot1 size : 4 Mb EMMC boot2 size : 4 Mb EMMC gp1 size : 0 Mb EMMC gp2 size : 0 Mb EMMC gp3 size : 0 Mb EMMC gp4 size : 0 Mb EMMC user area size : 14910 Mb Reading Partition Table Reading FRP Partition Writing FRP Partition data Reset FRP (MTK Loader) done. Performed by ‪1.2.0‬ Software version.

08-12-2020, 08:36	#210 (permalink)
faisal naeem Freak Poster Join Date: Jan 2018 Location: Gujranwala punjab pakistan Posts: 110 Member: 2803352 Status: Offline Thanks Meter: 77	Telenor Infinity I4 User Lock Remove Done with Octoplus FRP Tool [IMG]file:///C:/Users/FAISAL%20NAEEM/Desktop/infinity%20i4.jpg[/IMG]